644646
50
Verklein
Vergroot
Pagina terug
1/62
Pagina verder
39
Robomow S models
Message
Displayed
Probable Cause/Event Corrective/User Action
Recharge battery
- The maximum operating time has been
reached (displayed in non-Base Station zone).
- Mower is searching for the Base Station but
the battery voltage is too low to continue the
searching process.
- Connect the charger to the mower or place it in the Base
Station for charging.
- Drive the mower manually using the remote control or
carry it by hand for charging in the Base Station.
Start elsewhere
- Drive wheel motors have been working under
a severe load during automatic or manual
operation.
- Check to insure the mower is not stuck, allowing the
drive wheels to slip.
- Check the ground around the mower for holes or
indentations. Fill with dirt and level off.
- Check if the drive wheels are free to rotate and nothing
blocks them.
- Remove the mower away from this particular location
and restart operation.
Start inside
- Automatic operation is initiated while the robot
is placed out of the Perimeter Wire loop.
- Place the mower inside the lawn and press the
button.
- Swap wires in the plot connector.
Stuck in place
- Robomow got stuck in place. It cannot continue
driving.
- Check the ground for holes or indentations, where the
mower has stopped and fill it with dirt and level off –
especially in the area close to the perimeter, where the
Robomow turns in place.
- Robomow has difficulty to turn in place
because the front wheel is blocked by a hole
or indentation. It caused the mower to turn in
place without detecting wire or bumper.
- Verify that the area is not too steep.
- Work mainly in dry conditions.
- Check if the Perimeter Wire is not too close to the edge
– move if required.
- Verify that the mowing deck is not set too low.
Sub-Zone X
Problem
- Sub-Zone 1/2/3/4 entry problem.
- The mower either fails to leave / bypass the
Base Station on its way to the Sub-Zone, or
fails to enter the Sub-Zone.
- The mower will try to reach the Sub-Zone every
two hours. If the mower fails to reach the Sub-
Zone within three attempts, it will stay in the
Base Station until the end of current mowing
cycle. It will not skip to the next Sub-Zone (if
there are any), if it fails to reach the current one.
- Try to start manual mowing (refer to section 4.5 –
Manual Operation). Check if something disturbs
mower’s driving backwards and/or bypassing the Base
Station. Confirm the mower drives along the perimeter
wire and doesn’t fall off the lawn’s edge, when it departs
from the Base Station.
- Confirm that the mower is able to follow the perimeter
wire along the narrow pass until it reaches the Sub-
Zone. Refer to section 2.2.2 for instructions on how to
set a narrow pass properly.
Switch off
before lifting
- The user carries Robomow manually while the
Safety Switch is On.
- Switch Off the Safety Switch before carrying Robomow.
Waiting for
Signal…
- Robomow has stopped the operation: it does
not detect a signal.
- Check the power to the Power Box.
- It may be an electrical power interruption. There is no
need to do anything. Robomow will renew operation as
soon as power is back.
- תועמשמשיםא,ךרוצןיאםא
EN
50

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robomow MS2500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robomow MS2500 in de taal/talen: Engels als bijlage per email.

De handleiding is 16,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Robomow MS2500

Robomow MS2500 Gebruiksaanwijzing - Nederlands - 64 pagina's

Robomow MS2500 Gebruiksaanwijzing - Deutsch - 62 pagina's

Robomow MS2500 Gebruiksaanwijzing - Français - 62 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info