520094
83
Verklein
Vergroot
Pagina terug
1/105
Pagina verder
Model menu
Snap roll
Multi-motor
FX-40
The servo transit speed of all three control surfaces can be
entered individually for each direction, separately for the
there’ and ‘back’ directions. A separate programming mask is
provided in the second display level, as shown below.
Mark the appropriate field, and enter the desired value using
the arrow buttons. The adjustment range is 0 to 27 increments.
The highest number equates to a servo travel time of up to
nine seconds.
The screen shot below shows a typical servo run time set-up:
When you have completed the programming of a snap roll
manoeuvre, it is fundamentally essential to check everything
very carefully on the model itself.
18.20 MULTI-MOTOR
SETTINGS FOR MULTI-MOTOR MODELS
This function enables you to define the most important set-
tings for contr
olling the motors in a model air
craft with up to
four power plants. These settings are as follows:
Motor cut-off functions (Motor off)
Idle settings (Idle 2)
Idle-up (Auto-rotation)
Full-throttle trims (Trim max.)
Idle trims (Trim idle)
To enter values for these settings you must first activate each
of the throttle servos (THR, THR2), and then enter the servo
position as a percentage.
With the ‘Power model’ type already set, mark the ‘Multi-
motor’ option in the Model menu. The screen display now
looks like this:
This menu will differ according to the particular model type
you have selected. The number of throttle channels displayed
on the screen is dictated by the number defined in the model
configuration. Our example shows two (maximum: four).
The first step is to activate the whole function for each throttle
channel (THR, THR2 etc.) in the Status line: mark the field, and
the display changes from ‘INH’ (inactive) to ‘ON’.
After this you can enter the settings for ‘Motor off’ and ‘Idle 2’
for each motor: the first step is to activate the function in the
Status line, and then enter the servo position (Posi.). Mark the
appropriate field to activate the function, then enter the posi-
tion in the form of a percentage value. After marking the field
you can a new value using the arrow buttons. The adjustment
range is 0% to 50%; the default setting is 17%. Pressing
‘Reset’ restores the default setting.
In the bottom line you will see the Auto-rotation (Motor Hold)
option, which can be activated individually for each motor.
Mark the appropriate field: the screen displays ‘ON’, and the
throttle servos run to the values set in the ‘Motor pos’ window.
This option sets one motor to a particular value, so that you
can adjust a second motor independently of it.
In the second level of the display you can set the values for the
trims - for full-throttle and idle - separately for each motor. The
required value is entered as a percentage figure in the ‘Rate’
line, using the arrow buttons. A separate field contains the pre-
fix, so you can reverse the direction of the servos if necessary
to suit your installation. The adjustment range is 0% to 30% in
each case. The default setting is 0%; pressing ‘Reset’ restores
that setting.
82
83

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robbe Futaba FX-40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robbe Futaba FX-40 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Robbe Futaba FX-40

Robbe Futaba FX-40 Gebruiksaanwijzing - Deutsch - 105 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info