520094
76
Verklein
Vergroot
Pagina terug
1/105
Pagina verder
Model menu
Trim Mix 1 and 2
FX-40
increments) corresponds to a duration of nine seconds. The
default setting is always ‘0’. When you mark one of the
fields ‘there’ or ‘back’, the button fields for the arrows
appear at the right margin.
The servo speed mode can also be defined in the centre
field: the two options are linear and symmetrical modes.
Linear mode is used for controlling the throttle servo and for
switches; this mode is not self-neutralising. The alternative
(symmetrical) mode is self-neutralising, and is therefore the
default setting for all control surfaces.
This screen shot shows the results of programming an
exponential mixer curve for the ‘Butterfly’ option.
Assigning a trim compensation mixer
Deploying a Butterfly braking system generally causes a
nose-up or nose-down pitch trim change, i.e. a lateral axis
trim corr
ection is r
equired. In the final sub-menu you can
select a suitable elevator travel to compensate for the
unwanted pitch change. The mixer rates and the curve can
be set up and adjusted using the method which should be
familiar by now.
The same technique is also employed for adjusting the tran-
sit speed of the elevator servos.
Finally, please note that the programming options and the
actual appearance of the screen display may vary slightly
according to the model type and wing type you have selected.
18.12 TRIM MIX 1 AND 2
This menu is
used to set up
mixers which
apply to all the
wing contr
ol
s
urfaces and
the elevators,
separately for
particular flight
phases. The
software of the
FX-40 provides
two flight phase
mixers (Trim Mix
1 and 2), but
both mixers are
programmed in
exactly the same way, so this Section only describes the set-
up procedure for the first mixer.
A typical application would be for a model glider, with Trim Mix
1 set up to provide the optimum control surface settings for
the winch launch phase of the flight. These settings would
lower the ailerons and the flaps in order to give the model
maximum possible lift on the winch line. To ensure a stable
pitch attitude on tow, the mixer includes an option for entering
an elevator Offset to provide pitch trim compensation (i.e.
around the lateral axis).
In our example the second mixer (Trim Mix 2) might be used to
set up the optimum control surface settings for the speed
phase of the flight, with ailerons and flaps raised slightly in
order to minimise the aircraft’s drag.
These options are designed to ensure that reliable, reproduci-
ble control surface travels can be recalled again and again
when you select these flight phases. The settings can be cal-
led up using any switch you like.
An Offset can be entered for each of the wing control surfaces
- up to four ailerons and four flaps - in order to fine-tune the
individual wing flap neutral positions. You can also assign one
of the auxiliary transmitter controls for fine-tuning the system.
This allows you to set up a pre-set position for all the control
surfaces prior to fine-tuning in flight. As with all mixers, you
can select ‘Glob’ or ‘Sepa’ mode as desired.
You can also define a trigger switch which activates the set-
tings for the flight phase. At the same time you can determine
whether the function is triggered by a switch (manual mode) or
by a transmitter stick (automatic mode). Naturally, your prefer-
red stick can be selected individually.
It is possible to set the required transit speed individually for
the aileron servos, flap servos and elevator servos, with sepa-
rate settings for the ‘there’ and ‘back’ directions. If you wish,
you can program a delay time for this mixer function, so that
the transition is smooth rather than abrupt.
Start by marking the desired option ‘Trim Mix 1’ or ‘Trim Mix 2’
in the Model menu. The screen display for the ‘Trim Mix 1’
option now looks like this:
75
Tip aileron
(AIL3)
Main
aileron
(AIL)
Spoiler
(FLAP)
Spoiler
(FLAP2)
Brake flaps
(BRFL & BRFL2)
Main
aileron
(AIL2)
Tip
aileron
(AIL3)
V-tail Ailvator
ELE
ELE
ELE2
ELE2
76

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robbe Futaba FX-40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robbe Futaba FX-40 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Robbe Futaba FX-40

Robbe Futaba FX-40 Gebruiksaanwijzing - Deutsch - 105 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info