520094
42
Verklein
Vergroot
Pagina terug
1/105
Pagina verder
Linkage Menu
FX-40
16.6 FREQUENCY
SELECTING THE FREQUENCY CHANNEL AND
MODULATION
This menu has already been described in detail on page 20 in
the Section entitled ‘Using the transmitter for the first time’, so
it will only be r
epeated her
e briefly in order to maintain the cor-
rect sequence.
42
The receiver number (printed on the back panel of the recei-
ver) has been entered; a frequency channel can only be trans-
mitted to the receiver if the correct receiver number is trans-
mitted at the same time.
Input field for second receiver number (for large-scale model
aircraft).
Press the Frequency channel button, and a three-page selec-
tion of spot frequencies appears, showing all those which are
approved for use in Europe. Select a channel which is appro-
ved in the country where you wish to operate the model.
Press the ‘Enter’ button to confirm the new spot frequency
you have selected (or press the ‘Back’ button to interrupt
the function without changing frequencies).
Once you have selected a spot frequency, a confirmation dis-
play appears so that you can check the new channel. The
screen also asks whether you now wish this information to be
transmitted to the receiver.
Confirm this by pressing the “Yes” button.
The screen switches to the transmission display where the
transmission is displayed in graphic form; an audible signal
sounds, and the monitor LED flashes blue.
While this is happening (within two or three seconds) you
must switch the receiver on (or off, then on again). If this
does not work, switch the receiver off and on again.
When the receiver has picked up the signal and changed
frequencies, the monitor LED on the receiver flashes once,
and a servo connected to channel 1 moves three times
briefly around its centre position.
NOTE!
The frequency information is transmitted at very low power,
with an effective range of ar
ound two or three metres. For the
system to work correctly it is absolutely essential to unwind
the receiver aerial and screw the transmitter aerial into its
socket (if not already in place).
In the immediate vicinity of PCs, transformers, fluorescent
lights, Bluetooth equipment, mobile telephones etc., the trans-
mission may be affected by interference since these devices
are much more powerful. If this should occur, seek out a loca-
tion where the level of ‘electro-smog’ is much lower.
If the monitor LED on the receiver starts flashing after you have
initiated the frequency channel transmission process, or if the
receiver fails to confirm reception using the indicators mentio-
ned earlier, then the frequency switch has not taken place.
Position the receiver closer to the transmitter, then repeat the
procedure by pressing the “Repeat” button.
The frequency information is transmitted on channel 80 of the
35 MHz band, and if this channel is already in use by another
transmitter, the power of the FX-40 transmitter may not be suf-
ficient for changing the spot frequency. In this case place both
aerials very close together, or carry out the channel switch
using the DSC lead.
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robbe Futaba FX-40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robbe Futaba FX-40 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Robbe Futaba FX-40

Robbe Futaba FX-40 Gebruiksaanwijzing - Deutsch - 105 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info