520094
7
Verklein
Vergroot
Pagina terug
1/105
Pagina verder
Transmitter controls
FX-40
7
In the Linkage menu “Dial Monitor” the current and stored
positions of the rotary knobs are displayed in bar graph form.
The centre rotary knob CD is a digital control with no end-
stops, and it also features an integral push-button function
(CD-SW). This control can also be assigned freely to any func-
tion. The transmitter emits an audible signal when the knob is
moved to the centre position. The position of this control is
also displayed on the Start screen.
LINEAR SLIDERS
The centre of the transmitter houses three linear sliders with a
centr
e detent. These analogue contr
ols can also be assigned
freely to any function you wish. The transmitter emits an audi-
ble signal when the slider is moved to the centre position.
In the Linkage menu “Dial Monitor” the current and stored
positions of the linear sliders are displayed in bar graph form.
DIGITAL TRIMMERS
The transmitter features two digital trimmer buttons (T5 + T6).
Every time a button is moved, the trimmer value alters by the
selected incr
ement. If a trimmer button is held at one end-
point in or
der to adjust the trimmer value by a larger amount,
the rate of change automatically accelerates (auto-repeat
function).
If the trimmer position reaches the neutral point (centre posi-
tion), or passes the neutral point, the transmitter emits an
audible signal. The current trim position is displayed as a bar
graph in the Start display and also in the “Dial Monitor” menu.
The trimmer buttons can be assigned freely to any functions,
and can also be used as transmitter controls for mixer func-
tions.
The trimmer rate and increment can be selected individually
for each trim button in the “Function” menu.
• You can fit the switches in any position you like.
The default position of the switches is as follows:
In each case the centre wir
e of the cable is colour-coded, and
is assigned permanently to the following switches:
Please ensure that the wire
colours are correctly connec-
ted after you have r
e-positio-
ned the switches, otherwise
the graphical on-scr
een
assignment will be displayed
incorrectly.
After re-positioning the switches, fit the crown nuts again
and tighten them using the special spanner supplied.
Fit the back panel and tighten the retaining screws.
After the re-positioning exercise you should now call up the
System menu “Switch” (page 35) and alter the switch types
and position numbers, so that the graphical switch position di
play reflects the new configuration and is displayed correctly on
the screen.
CENTRAL ROTARY KNOBS
The rotary knobs LD and RD are analogue contr
ols which can
be assigned freely to any function. They feature a fine centre
detent, and the transmitter emits an audible signal when they
are moved to the centre position. If you wish, they can be
retracted by pushing the knob in using light pressure.
Switch Position Typ Lever
SA 3-position Change-over Short
SB 3-position Change-over Short
SC 3-position Change-over Long
SD 3-position Change-over Short
SE 3-position Change-over Short
SF 2-position Change-over Long
SG 3-position Change-over Short
SH 3-position Change-over Short
SWITCH Cable colour
SA and SC green
SB and SD yellow
SE and SG orange
SF and SH brown
L1
L2
L3
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robbe Futaba FX-40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robbe Futaba FX-40 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Robbe Futaba FX-40

Robbe Futaba FX-40 Gebruiksaanwijzing - Deutsch - 105 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info