8437
31
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
31
Fig. 21 N - V controller, boiler with 7 and 9 sections
Fig. 22 N - V controller, boiler with 11 to 19 sections
16. Switch the boiler to full load by selecting option
"Load maximum" with the ' ' button and confirming it
with the ' ' button.
Compare the CO
2
percentage with the value men
tioned in the table. Adjust, if necessary, this CO
2
percentage with the V-controller. Switch the boiler to
part load, measure and compare the CO
2
percentage
with the value mentioned in the table and adjust, if
necessary, the value with the N-controller.
17. Repeat this full load/part load switching until the CO
2
percentages at full load/part load come within the
tolerances mentioned in the table.
18. By pressing the ' ' button, the main menu of the
service level reappears. Now set the desired boiler
control, as described in para. 7.3.3.
By pressing the ' ' button three times, you return to
the main menu of the user level.
19. After commissioning, enter the preset values in the
table on the boiler.
20. Send the CE commissioning report to Broag.
11.3 Shut down the boiler
1. Turn off the power supply to the boiler.
2. Close the main gas cock.
3. Turn off the boiler control.
Please note! Frost protection may be required.
12. FAULT-FINDING
- Now select the option “History data” with the ' ' button
and confirm it with the ' ' button.
- Now select the lock out or shut down failure memory
using the ' ' button. Confirm with the ' ' button.
Depending on the option selected, the number of
locking failures stored in the memory (maximum 5 of
each) is now displayed.
Failure No. 1 is the failure which occurred last, failure
No. 2 the last but one, etc.
To know which failure occurred last, the failure counter
must be set to 1 using the ' ' and ' ' buttons. When the
' ' button is pressed for confirmation, the failure in
question is indicated. Using the ' ' button, various
menus can now be called up, all indicating the opera-
tional condition of the boiler at the moment of failure.
In the table below the various failure messages are dis-
played which may appear on the LCD-display, followed by
the instructions to eliminate the failure.
For possible measurement methods see chapter 11:
"Commissioning". When a failure message appears that
is not selfexplanitory, and is not displayed in the table,
then contact our service department.
Note:
When reporting a failure code, write down the exact mes-
sage and the parameters at which the failure occured.
12.1 General
For troubleshooting use the wiring diagram and the swit-
ching sequence diagram in paragraph 10.9. The instru-
ment panel is provided with an alphanumeric LCD-display.
In the case of failure, the display indicates the cause of
the failure and how long ago the boiler went into failure
mode. The failure and the operating condition at the time
of failure are stored in the memory of the control unit.
Five blocking and five locking failures can be stored in
this memory. If a failure in a boiler repeats itself several
times in rapid succession, this failure is stored only once.
Locking failures can be reset using the reset button on
the instrument panel (' ').
12.2 Faults
In the case of failure, the LCD-display indicates the cause
of the failure. It also indicates whether it is a blocking or
locking failure and how long ago it occurred. In the case
of a blocking failure, the boiler will automatically restart
when the cause of the failure has been eliminated. If the
same blocking failure has occurred 5 times in rapid suc-
cession, the boiler will lock out. Displaying the operational
condition at the time when the failure occurred speeds up
the search for the cause of failure.
Proceed as follows:
- Select the service level by travelling down the user
menus using the ' ' button. Enter code 00 12 using the
'' and ' ' buttons and confirm it with the ' ' button.
31

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Remeha-Gas-3002-ECO

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Remeha Gas 3002 ECO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Remeha Gas 3002 ECO in de taal/talen: Engels als bijlage per email.

De handleiding is 1,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Remeha Gas 3002 ECO

Remeha Gas 3002 ECO Bijvullen ketel - Nederlands - 2 pagina's

Remeha Gas 3002 ECO Gebruiksaanwijzing - Deutsch - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info