8437
29
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
29
11. Now select the option "Fan on?" and confirm with
the '
'-button. The fan will start now. Switch the fan
to maximum speed by selecting this option.
Confirm with the ' '-button. Now press the ' '-button.
Select the option "Service settings" and confirm
with the ' '-button. Press the ' '-button. Select the
option "Pressure settings"; confirm with the ' '-button.
Set the maximum differential pressure at 900 Pa,
using the ' '-button. Confirm with the ' '-button.
Now press several times the ' '-button until you
reach the menu where you can read out the air
differential pressure.
A differential pressure of 900 Pa has to be reached.
If not, check the dimensions of the flue gas discharge
system. Set the maximum differential pressure in the
service level back at the standard level of 840 Pa.
Confirm with the ' '-button. Set the minimum
differential pressure at 110 Pa for the minimum load
of 33%.
12. Check the opening pressure of the gas block.
Connect a pressure differential device to the measu-
ring points pG and pF (see fig. 19 for 7 and 9 sec-
tions and fig. 20 for 11 to 19 sections). Open the
main gas cock (vent the gas line). Disconnect the
ignition device from the ignition electrode.
Press several times the ' '-button, until you reach
the menu with the selecting option "Service settings".
Select this option and confirm with the ' '-button.
Now select "Boiler on?"; confirm with the ' '-button.
The boiler now will make a start attempt without igni-
tion. As soon as the gas valve opens, the opening
pressure can be read out on the pressure differential
device. The ope ning pressure should be bet ween 1
and 3 mbar. When you read out a higher pressure,
turn the N-controller to the left. Repeat point 12 after
resetting the boiler. When the openings pressure lies
between 1 and 3 mbar, a correct presetting is
assured. Connect the ignition device again to the igni-
tion electrode and reset the boiler. Select in the serv-
ice level again the option "Service tests" and confirm
with the ' '-button.
13. The cursor is now placed on option “Boiler on?”.
Press the ' '-button. The control unit will now start
from neutral position. After an internal check and a
check of the differential air pressure, the fan will start.
As soon as the differential air pressure is sufficiently
high, the pre-purge time is started. The fan now pre-
purges for 30 seconds at full load. Then the fan slows
to minimum load. The pre-ignition is activated and the
gas valve opened. If, at the end of the safety time,
there is a sufficient signal from the pilot flame (the
flame is checked with a second ionisation probe) the
boiler will start operating at part load (mi ni mum load).
Gas distribution pipe
Fig. 19 Differential pressure measuring points (boiler with 7 and 9 sections)
blue
black
burner
black
blue
Side view
P gas = PF+PG
P air = PL+PF
Gas multi-block
29

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Remeha-Gas-3002-ECO

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Remeha Gas 3002 ECO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Remeha Gas 3002 ECO in de taal/talen: Engels als bijlage per email.

De handleiding is 1,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Remeha Gas 3002 ECO

Remeha Gas 3002 ECO Bijvullen ketel - Nederlands - 2 pagina's

Remeha Gas 3002 ECO Gebruiksaanwijzing - Deutsch - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info