726815
9
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
Operating and
installation instructions
Read the instructions prior to performing any task!
REMKO Smart-Control Touch
Remote control for heat pumps
0225-2020-05 Edition 2, en_GB
Quick guide
Translation of the original
Read these operating instructions carefully before commis-
sioning / using this device!
These instructions are an integral part of the system and must
always be kept near or on the device.
Subject to modifications; No liability accepted for errors or mis-
prints!
Table of contents
1 Safety and usage instructions............................................................................................................. 4
1.1 General safety notes....................................................................................................................... 4
1.2 Identification of notes...................................................................................................................... 4
1.3 Personnel qualifications.................................................................................................................. 4
1.4 Dangers of failure to observe the safety notes................................................................................ 4
1.5 Safety-conscious working............................................................................................................... 4
1.6 Safety notes for the operator........................................................................................................... 5
1.7 Safety notes for installation, maintenance and inspection.............................................................. 5
1.8 Unauthorised modification and changes......................................................................................... 5
1.9 Intended use................................................................................................................................... 5
1.10 Warranty........................................................................................................................................ 5
1.11 Transport and packaging............................................................................................................... 6
1.12 Environmental protection and recycling........................................................................................ 6
2 Technical data........................................................................................................................................ 7
3
Product description.............................................................................................................................. 8
4 Electrical wiring and interfaces........................................................................................................... 8
5 WLAN function...................................................................................................................................... 9
6 Assembly and installation.................................................................................................................. 15
7 Index..................................................................................................................................................... 20
3
1 Safety and
usage instructions
1.1 General safety notes
Carefully read the operating manual before com-
missioning the units for the first time. It contains
useful tips and notes such as hazard warnings to
prevent personal injury and material damage.
Failure to follow the directions in this manual not
only presents a danger to people, the environment
and the system itself, but will void any claims for
liability
.
Keep this operating manual and the refrigerant
data sheet near to the units.
1.2 Identification of notes
This section provides an overview of all important
safety aspects for proper protection of people and
safe and fault-free operation.The instructions and
safety notes contained within this manual must be
observed in order to prevent accidents, personal
injury and material damage.
Notes attached directly to the units must be
observed in their entirety and be kept in a fully
legible condition.
Safety notes in this manual are indicated by sym-
bols. Safety notes are introduced with signal words
which help to highlight the magnitude of the danger
in question.
DANGER!
Contact with live parts poses an immediate
danger of death due to electric shock. Damage
to the insulation or individual components may
pose a danger of death.
DANGER!
This combination of symbol and signal word
warns of a situation in which there is immediate
danger
, which if not avoided may be fatal or
cause serious injury.
WARNING!
This combination of symbol and signal word
warns of a potentially hazardous situation,
which if not avoided may be fatal or cause
serious injury
.
CAUTION!
This combination of symbol and signal word
warns of a potentially hazardous situation,
which if not avoided may cause injury or mate-
rial and environmental damage.
NOTICE!
This combination of symbol and signal word
warns of a potentially hazardous situation,
which if not avoided may cause material and
environmental damage.
This symbol highlights useful tips and recom-
mendations as well as information for efficient
and fault-free operation.
1.3 Personnel qualifications
Personnel responsible for commissioning, opera-
tion, maintenance, inspection and installation must
be able to demonstrate that they hold a qualifica-
tion which proves their ability to undertake the
work.
1.4
Dangers of failure to observe
the safety notes
Failure to observe the safety notes may pose a risk
to people, the environment and the units. Failure to
observe the safety notes may void any claims for
damages.
In particular, failure to observe the safety notes
may pose the following risks:
n The failure of important unit functions.
n The failure of prescribed methods of mainte-
nance and repair
.
n Danger to people on account of electrical and
mechanical effects.
1.5 Safety-conscious working
The safety notes contained in this manual, the
existing national regulations concerning accident
prevention as well as any internal company
working, operating and safety regulations must be
observed.
REMKO Smart-Control Touch
4
1.6 Safety notes for the operator
The operational safety of the units and compo-
nents is only assured providing they are used as
intended and in a fully assembled state.
n The units and components may only be set up,
installed and maintained by qualified per-
sonnel.
n Protective covers (grille) over moving parts
must not be removed from units that are in
operation.
n Do not operate units or components with
obvious defects or signs of damage.
n Contact with certain unit parts or components
may lead to burns or injury
.
n The units and components must not be
exposed to any mechanical load, extreme
levels of humidity or extreme temperature.
n Spaces in which refrigerant can leak sufficient
to load and vent. Otherwise there is danger of
suffocation.
n All housing parts and device openings, e.g. air
inlets and outlets, must be free from foreign
objects, fluids or gases.
n The units must be inspected by a service tech-
nician at least once annually. Visual inspec-
tions and cleaning may be performed by the
operator when the units are disconnected from
the mains.
1.7 Safety notes for installation,
maintenance and inspection
n Appropriate hazard prevention measures must
be taken to prevent risks to people when per-
forming installation, repair
, maintenance or
cleaning work on the units.
n The setup, connection and operation of the
units and its components must be undertaken
in accordance with the usage and operating
conditions stipulated in this manual and comply
with all applicable regional regulations.
n Local regulations and laws such as Water
Ecology Act must be observed.
n The power supply should be adapted to the
requirements of the units.
n Units may only be mounted at the points pro-
vided for this purpose at the factory. The units
may only be secured or mounted on stable
structures, walls or floors.
n Mobile units must be set up securely on suit-
able surfaces and in an upright position. Sta-
tionary units must be permanently installed for
operation.
n The units and components should not be oper-
ated in areas where there is a heightened risk
of damage. Observe the minimum clearances.
n The units and components must be kept at an
adequate distance from flammable, explosive,
combustible, abrasive and dirty areas or
atmospheres.
n Safety devices must not be altered or
bypassed.
1.8
Unauthorised modification
and changes
Modifications or changes to units and components
are not permitted and may cause malfunctions.
Safety devices may not be modified or bypassed.
Original replacement parts and accessories
authorised by the manufactured ensure safety
. The
use of other parts may invalidate liability for
resulting consequences.
1.9 Intended use
The units are designed depending on the model
and equipment exclusively as a control unit for the
heat pump and the heating system.
Any different or additional use shall be classed as
non-intended use. The manufacturer/supplier
assumes no liability for damages arising from such
use. The user bears the sole risk in such cases.
Intended use also includes working in accordance
with the operating and installation instructions and
complying with the maintenance requirements.
Under no circumstances should the threshold
values specified in the technical data be exceeded.
1.10 Warranty
For warranty claims to be considered, it is essential
that the ordering party or its representative com-
plete and return the "certificate of warranty" to
REMKO GmbH & Co. KG at the time when the
units are purchased and commissioned.
The warranty conditions are detailed in the "Gen-
eral business and delivery conditions". Further-
more, only the parties to a contract can conclude
special agreements beyond these conditions. In
this case, contact your contractual partner in the
first instance.
5
1.11 Transport and packaging
The devices are supplied in a sturdy shipping con-
tainer or inside the heat pump casing. Please
check the equipment immediately upon delivery
and note any damage or missing parts on the
delivery and inform the shipper and your contrac-
tual partner
. For later complaints can not be guar-
anteed.
WARNING!
Plastic films and bags etc. are dangerous
toys for children!
Why:
- Leave packaging material are not around.
- Packaging material may not be accessible to
children!
1.12 Environmental protection
and recycling
Disposal of packaging
All products are packed for transport in environ-
mentally friendly materials. Make a valuable contri-
bution to reducing waste and sustaining raw mate-
rials. Only dispose of packaging at approved
collection points.
Disposal of equipment and components
Only recyclable materials are used in the manufac-
ture of the devices and components. Help protect
the environment by ensuring that the devices or
components (for example batteries) are not dis-
posed in household waste, but only in accordance
with local regulations and in an environmentally
safe manner
, e.g. using certified firms and recy-
cling specialists or at collection points.
REMKO Smart-Control Touch
6
2 Technical data
Series Smart Control Touch
Operating mode Remote control / controller
Power supply V +12 V DC
Enclosure class IP 30
Power consumption mW < 100
Max. cable length m 15
Recommended cable
mm
2
2 x 0.5
Dimensions
Height mm 150
Width mm 80
Depth mm 35
Environment
Ambient temperature °C 0-70
Air humidity % rH 0-95 (relative) non-condensing
Remote control EDP no. 248104
WLAN stick EDP no. 1121589
Ethernet adapter 248108
We reserve the right to make technical changes for the purpose of technical advancement.
7
3 Product description
Information about assembly and installation can be
found on the following pages of the operating
manual. Information on operating the REMKO
Smart Control T
ouch remote control can be found
in the "REMKO Smart-Control Touch" operating
manual. This remote control gives you options for
setting and querying the relevant parameters of the
REMKO heat pump at the user and expert levels.
All setting procedures overwrite the existing set-
tings on the heat pump controller. Either for a
defined heating circuit or parameters for the entire
system. The specific information for operating the
remote control at the "User" level can be found in
the "REMKO Smart Control Touch" manual. You
will find that operation is intuitive and logical. The
parameters relevant to specialists are enabled at
the "expert level" and are only intended for spe-
cialist personnel. It contains all the information
required for installation and commissioning of the
remote control by REMKO Service or the installer.
The remote control has the same parameters as
the regulation system in the heat pump. Assembly
should take place in a reference room such as the
living room where there is easy access. The
REMKO room sensor can be used to determine
the current room temperature and air humidity.
Since you have full access to all the parameters of
the installed heat pump via the remote control, it
cannot be used in so-called tenant mode. A WLAN
function is available via the installed WLAN stick as
standard. This gives you the option of connecting
your remote control to the in-house WiFi-enabled
router and your smartphone. A description of this
function can be found on the following pages.
The following examples for connecting the
REMKO remote control require software ver
-
sion 4.26. If the software is not up to date,
updating to software version 4.26 or later must
be carried out!
4 Electrical wiring and
interfaces
12V GND
802.11n
1
2
3
Fig. 1: Electrical wiring and interfaces
1
Network cable connection (LAN cable)
2
Power supply connection
(12V/GND)
For the surface-mounted installation, the trans-
former included in the scope of delivery is used for
the power supply (230V~ / 12V
). If the unit is
flush-mounted, a 12V direct current source must
be provided at the installation position.
3
WiFi receiver (WLAN stick)
The available WiFi receiver is required if a wireless
network connection is to be used.
REMKO Smart-Control Touch
8
5 WLAN function
Basic schema of the REMKO Smart Control
T
ouch
The power supply (+12V) of the controller can
also be established by the customer with an
external mains power supply
. Refer in this
regard to the technical data for the connection.
Setting up and installing the WLAN function can
be found in the corresponding operating instruc-
tions for the Smart-Control T
ouch controller.
Observe the separate controller instructions for
commissioning and programming the REMKO
Smart-Control T
ouch controller.
Basic schema of the Smart Control Touch with WLAN connection and remote control
Functions: Smart Control T
ouch connection of the heat pump to the customer’s WLAN router via WLAN and
remote control with WLAN function in the WLAN network of the router.
A: Heat pump I/O module
B: Smart Control Touch heat pump
C: Customer’s WLAN router with Internet connec-
tion
D: Remote control
1: Ethernet interface/patch cable (LAN cable)
2: Power supply: +12V, terminal B1/A1
3: 12V/GND connection to customer’s transformer
Connection of the Smart Control Touch controller to a customers WLAN router via a WLAN connection using
an additional remote control on the same WLAN network.
n The mains voltage (12V) for the remote control must be supplied by the customer!
9
Basic schema of the Smart Control Touch with WLAN connection and remote control
Smart Control regulation system connection via LAN cable (patch cable)
Functions: Smart Control T
ouch connection of the heat pump to the customer’s WLAN router via LAN cable
(patch cable) and remote control with WLAN connection in the WLAN network of the router.
A: Heat pump I/O module
B: Smart Control Touch heat pump
C: Customer’s WLAN router with Internet connec-
tion
D: Remote control
E: Ethernet adapter
F: WLAN stick (remove)
1: Ethernet interface/patch cable (LAN cable)
2: Power supply: +12V, terminal B1/A1
3: 12V/GND connection to customer’s transformer
Connection of the Smart Control Touch controller to a customers WLAN router via a LAN cable (patch cable)
is done by connecting the internal WLAN stick.
n An Ethernet adapter is required for the connection.
n The mains voltage (12V) for the remote control must be supplied by the customer!
REMKO Smart-Control Touch
10
Basic schema of the Smart Control Touch with LAN cable connection of the remote control
Smart Control regulation system connection via WLAN network of the router
Functions: Smart Control T
ouch connection of the heat pump to the customer’s WLAN router via LAN cable
in the network of the router and remote control connection via LAN cable (patch cable).
A: Heat pump I/O module
B: Smart Control Touch heat pump
C: Customer’s WLAN router with Internet connec-
tion
D: Remote control
E: RJ 45 connection
F: WLAN stick (remove)
1: Ethernet interface/patch cable (LAN cable)
2: Power supply: +12V, terminal B1/A1
3: 12V/GND connection to customer’s transformer
Connection of the Smart Control Touch remote control to a customers WLAN router via a LAN cable (patch
cable) is done via the RJ 45 interface. The WLAN stick must also be removed.
n The mains voltage (12V) for the remote control must be supplied by the customer!
11
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO Smart-Control Touch bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO Smart-Control Touch in de taal/talen: Engels als bijlage per email.

De handleiding is 2,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van REMKO Smart-Control Touch

REMKO Smart-Control Touch Gebruiksaanwijzing - Nederlands - 24 pagina's

REMKO Smart-Control Touch Gebruiksaanwijzing - Deutsch - 24 pagina's

REMKO Smart-Control Touch Gebruiksaanwijzing - Français - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info