587902
14
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
14
REMKO PGT (E) series
Troubleshooting
Malfunctions: Cause:
Cause: Remedial measures:
Unit does not start.
Unit switches off during operation.
(Fault lamp in the automatic burner lights up)
Fan runs, but the gas supply is blocked
or no ignition takes place.
The gas supply is interrupted, or the flame is extinguished.
Unit consumes too much fuel.
Unit cannot be switched off.
Heating capacity drops in permanent operating mode.
Heating capacity cannot be regulated.
1 – 2 – 3 – 4 – 5 – 7 – 10 – 13 – 17 – 18
2 – 6 – 7 – 8 – 9 – 10 – 13 – 14 – 17
7 – 12 – 13 – 14
6 – 7 – 8 – 9 – 10 – 13 – 14 – 17 – 18
13
5 – 15
14
11
Connect the plug with an appropriate socket (230V/50Hz).
Check the motor, fan blade and drive clutch
and replace if necessary.
The setting must be higher than the current room temperature.
Connect the strapping plug with the thermostat socket.
Shut off the gas supply, unplug the power plug from the mains
power socket and replace the operating switch.
Check polarity, turn the power plug through 180°.
Check whether the gas supply to the unit is present.
Check the level of the gas cylinders.
Check the gas hose for damage.
Disengage or replace the hose breakage protection.
Settings according to specifications;
check the porcelain insulation of the electrodes.
Clean the protective intake grille.
Check the protective intake and outlet grilles (clean if necessary).
Check whether the fresh air supply is sufficient.
Unlock STB (reset STB).
Replace or clean gas control.
Operating switch to the "I" position (heating mode).
Check the ignition cable for damage.
Check the electrode settings, check cyclical igniter.
Fit an original pressure controller.
Disengage or replace the hose breakage protection.
Replace the gas cylinder(s) and connect 2-3 cylinders with the multi-
cylinder set, EDP no. 1014050.
Shut off the gas supply, allow the flame to burn out.
Operating switch to the "0" position and remove the power plug
from the mains power socket. Replace the solenoid valve.
Use foaming media to search for the leak and remedy this.
Reset the automatic burner by pressing the malfunction button.
Replace defective automatic burner.
1. The unit is not connected to the electricity supply.
2. The fan motor is overloaded or the
fan runs irregularly or is blocked.
3. The room thermostat is set too low.
4. No strapping plug in the room thermostat socket.
5. The operating switch is defective.
6. The polarity of the power plug is incorrect.
7. No gas pressure at the solenoid valve.
8. The ionisation or ignition electrode are incorrectly set.
9. The protective intake grille of the supply air fan is contaminated.
10. Shutdown by safety temperature limiter (STB).
The power plug (only PGT 100) was disconnected from the mains
power supply before the cooling time had passed.
11. The gas control is faulty or contaminated.
12. The ignition does not work.
13. The pressure controller is defective, an incorrect pressure control-
ler is fitted, or the hose breakage protection has interlocked.
14. The gas cylinder(s) is (are) iced up due to an excessively high gas
take-off and low temperatures.
15. The solenoid valve does not close.
16. Leaky gas connection.
17. The fault lamp in the automatic burner lights up.
18. The automatic burner is defective.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO PGT 60E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO PGT 60E in de taal/talen: Engels als bijlage per email.

De handleiding is 1,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van REMKO PGT 60E

REMKO PGT 60E Gebruiksaanwijzing - Nederlands - 24 pagina's

REMKO PGT 60E Gebruiksaanwijzing - Deutsch - 28 pagina's

REMKO PGT 60E Gebruiksaanwijzing - Français - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info