587981
18
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
This unit was manufactured using the latest production methods and tested repeatedly for perfect function.
If malfunctions still occur, please check the list according to the list below. In case of systems with indoor and
outdoor units, the "Troubleshooting and customer service" chapters in both operating instructions must be ob-
served. If all functional checks have been performed and the unit is still not functioning perfectly, please notify
your closest dealer.
Troubleshooting and customer service
Malfunction
Please observe the continuation of this fault remedy table on the next page
Fault Code Effect Possible cause Remedy
The
unit does
not start
The display does not light up. No power supply
Check the power connections at the
general supply terminals and check the
voltage values.
Check the fuses on the secondary side
of the additional transformer.
APS /
ASPh
The phase sequence relay does
not switch through.
Incorrect phase sequence.
The phase sequence relay
KA3 does not grant an
enable.
- LED not active.
Exchange the external conductor of the
power supply on the terminal strip on
the control panel.
The display is lit, but the unit
does not start.
Unit in standby
See the "Button functions" section for
the activation of the system.
OFF
The display indicates "OFF." No external enable
Check the connection to Terminals 2-3
(external enable).
The unit does not start and
the compressor symbol flashes
on the display.
Start-up delay
Wait until the start-up delay is over
(max. 360 sec.), after which the
compressor should start
The lower display flashes
and alternatively shows an
alphanumerical code and the
temperature value.
One or more of the
safety devices reacted
Check which safety device has reacted,
remedy the cause of fault, and reset the
safety device (see "Resetting faults")
C(n)tr
Compressor contactor defec-
tive, overcurrent protection
switch;
compressor reacted.
Does the compressor
symbol light up and is the
contactor energised?
Have the contactor or compressor
exchanged by a specialist company.
The unit
works
at a
reduced
cooling/
heating
capacity
The thermal load was in-
creased in the cooling mode.
Has a structural change
been made?
Observe safety distances.
C: Inlet flow temperature too
high.
H: Inlet flow temperature too
low.
Does the inlet flow
temperature amount to
about C = 5 - 10°C,
H = 35 - 50°C?
Reduce (C) or increase (H) the return
temperature.
Air in the medium circuit.
Have automatic bleed-
ers been installed at the
highest point?
Bleed manually or install an automatic
bleeder.
Condensation temperature too
high.
Are the fins clean and
have the operating limits
been observed?
Clean the fins, shade the unit, and ob-
serve the operating limits.
Incorrect parameter setting. Check the setting. Change the settings.
Inching mode due to low
demand.
Is the system oversized?
Increase the medium volume flow rate
by installing a storage tank.
Medium
outlet
Pipe leakage or insulation
defects.
Is leakage present and
are all lines insulated?
Seal off and insulate.
Thawing phase during heating
mode.
Is the heating mode set? Normal operating state.
REMKO KWG
18
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO KWG500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO KWG500 in de taal/talen: Engels als bijlage per email.

De handleiding is 7,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van REMKO KWG500

REMKO KWG500 Gebruiksaanwijzing - Deutsch - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info