Handleiding REL Acoustics ST III Range (pagina 19 van 27) (Engels)

457183

Verklein

Vergroot

Pagina terug

1/27

Pagina verder

REL Acoustics ‘ST III’ User Manual

Positioning

The optimal position for a REL is in one of the corners behind the main speakers. This

position provides 9 dB of mechanical amplification and allows for the most linear true low

bass wave launch, owing to the ability to tune the sub to the axial node of the room, or longest

throw distance.

The Process

To begin the set-up process, choose a piece of music that has a repetitive bass line that is

very low in frequency. We recommend cut 4 from the soundtrack to Sneakers (Columbia CK

53146). This has a repetitive bass drum throughout that gives you plenty of time to move the

woofer around, but more importantly, the recording venue was quite large for this recording,

and therefore it has a very deep and large-scale bass signature. This type of cut is perfect for

the set-up process, and should be played at the highest reasonable level expected for system

play back.

Working with a partner, one in the listening position and one at the woofer manipulating the

controls, is the most effective and efficient ways to set up the woofer. If working alone, the

initial steps in the set-up can very effectively be carried out from the location of the woofer.

Trying to ignore all other music in the cut, listen for the bass drum and its effect on the

listening room.

1. Phase Orientation: Once in the corner we need to adjust for phase. This may be the

single most critical step, and because it really is quite simple, it is often over thought,

especially by the most experienced audiophiles. Keep in mind; the right phase is

whichever position is the loudest or fullest. While playing music with true low bass,

adjust the crossover to a point where the sub and the speaker are sure to share

frequencies (B, 3 for big speakers or C, 4 for smaller speakers). At this point turn the

gain so that both sub and speaker are roughly equal and then switch, using the

“mode selector” switch, from “0” (position 1) to “180” (position 3) phase positions.

Again, whichever position is loudest or fullest is the correct position, and, as often as

not, may be 180-degree phase. That is, this position is working in harmony with your

main speakers, reinforcing bass, and not cancelling it.

2. Room Orientation: Next, if space allows, try two different orientations of the woofer

relative to the wall. First, while playing the set-up cut, place the REL with the

connection panel parallel with the rear wall. Second, place the REL with the

connection panel parallel with the sidewall. As with phase, the orientation which

yields the most output is the best position for that room. This process simply orients

the driver, and port, to most efficiently vent into the room. In some instances there

may be little difference, at which point aesthetic concerns may override performance

concerns. For Q series, if possible, point the driver directly out of the corner,

equidistant from the sidewalls.

3. Placement: The next step is to determine precisely how far out from the corner the

sub should be placed to achieve the most efficient output, as well as the lowest

frequency extension. With the sub fully into the corner, continuing to play the music,

slowly pull the sub from the corner on the diagonal, equidistant from both side and

rear wall . At a certain point (sometimes a matter of only a few inches, in rare cases

a foot or more) the sub will audibly go lower, play louder, and, if it truly locks on to the

room and is fully pressurising it, the air around the sub will seem to be energised,

stop right there! This is the correct position for the sub.

Crossover and Gain Settings: To determine the crossover point, bring the gain down, put the

crossover to A-1, bring the gain back up to the point where you have achieved a subtle

balance (In some situations where there may not be sufficient output due to room and

subwoofer interactions B-1 should be the position to use in setting initial gain). Working only

with the coarse control (A-D), bring the crossover point up until it is obviously too high, at this

point bring it down to the next lowest setting. Now, working with the fine control (1-6), bring up

the crossover point until it sounds too high, at which point bring it back down to the next

lowest setting. For all intents and purposes, this is the correct crossover point. Once this

stage has been reached, subtle changes to gain and crossover can be accomplished to

provide the last bit of complete and seamless integration. With that, set-up is complete.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

REL Acoustics ST III Range Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info