457183
18
Verklein
Vergroot
Pagina terug
1/27
Pagina verder
REL Acoustics ‘ST III’ User Manual
18
REL Set-Up Made Simple
RELs are not traditional subwoofers, but true sub-bass systems. A REL is designed to
augment the performance of “full range” speaker systems, to provide linear response down to
below 12 Hz (Studio III, -6 dB down at 9 Hz). Therefore, for the moment, set aside everything
you’ve been taught about subwoofers and how they are integrated into a stereo or theatre
system. RELs set-up and positioning differs from other subwoofers. A REL will take
advantage of physics and room acoustics to provide deep pressurisation as no other sub-
woofer can. It’s important that you bring to the set-up process a willingness to do things a little
differently in order to obtain these superior results. The end result of your labours will be an
utterly seamless integration of true deep bass to a sound system, regardless of the main
speaker’s low bass capability.
Two Things Before You Begin
A. It is helpful to know that you will almost always connect the REL to the input on the
rear panel labelled “Hi Level.” This connection is made using the supplied 34’ 10” (10
meters) cable, the bare leads of which connect to the speaker output terminals of the
power amplifier. The easy and foolproof connection at the REL is done with a Neutrik
Speakon connector. The purpose of connecting to the speaker output terminals is
one of the unique secrets of REL’s success. By connecting to the high level input on
the REL from the amplifier, you build forward the sonic signature of your main
system, including the tonal balance and timing cues of the entire electronics chain. In
this way, the REL is fed the exact signal that is fed to the main speakers.
B. When possible, the REL should be placed in one of the corners behind the speakers.
Remember, we are dealing with true LOW bass pressurisation with RELs, not the
mid-bass that most competitors settle for. Low bass pressurisation below 40Hz is
best derived from corner placement, where the most linear and efficient low bass can
be produced.
Basic set-up should take no more than ten to fifteen minutes to accomplish once connected.
Connecting
High-level connection, using the enclosed cable with the Neutrik Speakon connector,
is always the first choice. By connecting to the amplifier’s speaker outputs the sonic
signature of the entire amplification chain is folded into the signal for the sub, thereby
keeping timing and timbre cues consistent. In other words, the signal sent to the REL
is exactly the same signal sent to the speakers, allowing for seamless integration. This
connection can be made without affecting the performance of the amplifier because
the sub’s amplifier input impedance is 100,000 ohms. This scheme also avoids adding
any detrimental effects by not interposing any additional electronics into the
amplification chain.
The standard high level hook up procedure is: attach the red wire to the amplifier’s
right positive speaker output terminal; attach the yellow wire to the amplifier’s left
positive speaker output terminal; attach the black wire to which ever of the amplifier’s
ground output terminals is convenient; plug the Speakon connector into the sub’s
high level input.
For differential amplifiers using one sub, simply use the standard connecting scheme
with the exception of connecting ground to chassis ground, not to speaker output
ground, and then connecting into the high level input (Hi Input or Unbal Hi Input on
Stentor III and Studio III).
For differential amplifiers using two subs, one for each channel: connect red to
positive; yellow to negative; and black to chassis ground; plug the Speakon into the
balanced high level input (Bal Hi Input).
Low-level connection, RCA inputs (or XLR on some models), is always an option, should
high-level connection not be possible, or in a theatre system where both high-level and low-
level connection should be used. When connecting to the low level inputs, connect a single
RCA cable to the 0dB RCA jack. Additional gain can be achieved by connecting to the +12dB
input. If you are connecting two channels of stereo output from a pre-amplifier, simply use a
high-quality y-adapter to sum the two signals together.
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REL Acoustics ST III Range bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REL Acoustics ST III Range in de taal/talen: Engels als bijlage per email.

De handleiding is 0,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info