815522
26
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
26 12/237021-802L
Remove 2 screws on the
outside of hopper in the front
and 2 screws inside the
hopper at the back.
Figure 26.1
Convection Cover
Hook
Hook
Remove 2 screws at each end
Figure 26.2
Wing Nut
Bracket
Disconnect
Wires
Figure 26.3
Figure 26.4
Loosen Wing
Nut to relieve
pressure
Shaded area
inserted in hole in
Feed Tube
Rotate bracket counterclockwise
once pressure is relieved
With bracket in rotated position,
reach behind bracket and remove
and replace Snap Disc
Figure 26.5
B. Snap Disc #2
PART NUMBER: SRV7000-268
NOTE: Combustion Blower Gasket is also required. Sold
separately under Part Number SRV240-0812.
NOTE: You may need pliers to start the wing
nut (Figure 26.4).
10. When bracket is loose enough, rotate the
bracket counterclockwise and away from feed
tube (Figure 26.5).
11. Reach behind bracket and remove old snap disc. Install
new snap disc and rotate back to original position
ensuring the snap disc is inserted in the hole in the feed
tube. Tighten the wing nut and re-attach the wires to the
new snap disc.
12. Re-install in reverse order. Be sure to use new gasket
when installing combustion blower housing.
1. Turn down thermostat, let appliance cool completely
if running. Then unplug appliance before servicing.
Disconnect appliance from venting at the rear
of appliance.
2. Remove both upper and lower side curtains by removing
the six 7/16” nuts on the rear of the appliance.
3. Disconnect the vacuum hose and wires from the vacuum
switch. Disconnect the blue and white wires from the
combustion blower. Remove control box retainer clip.
Remove two screws that hold the junction box. Set aside
carefully. Disconnect hopper switch.
4. Remove cast top from appliance. Two fasteners are
located outside the hopper on each side. The other two
are located in the hopper along the back (Figure 26.1).
Remove the rear screen of the appliance (be sure the
vent is disconnected) by removing the seven screws. Lift
slightly upwards as to not damage the hopper switch and
set aside.
5. Remove lower screw by removing ve screws. Lay at
on ground.
6. Remove convection cover by removing the two screws
at the bottom (one each side) and slide to the left, then
set aside.
7. Remove the ve 7/16” bolts holding the combustion
blower housing to the exhaust plenum. Discard gasket.
(Clean blower impeller and plenum if needed).
8. Disconnect wires from snap disc #2 (Figure 26.3).
9. Loosen wing nut to relieve the pressure on snap disc
from the bracket. The shaded area of the snap disc is
inserted into a hole in the feed tube
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Quadra-Fire Castile - Pellet bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Quadra-Fire Castile - Pellet in de taal/talen: Engels als bijlage per email.

De handleiding is 8.11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Quadra-Fire Castile - Pellet

Quadra-Fire Castile - Pellet Gebruiksaanwijzing - Français - 40 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info