815522
25
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
25 12/237021-802L
A. Blowers
1. Convection Blower
PART NUMBER: 812-4900
NOTE: The convection blower must be removed before
the exhaust blower can be removed.
Side Screws,
Loosen Do Not
Remove
Side Screws,
Loosen Do Not
Remove
Remove back screws and
bend top back leaving it
attached at the bottom
Figure 25.1
Remove 6 screws
Figure 25.2
Figure 25.3
Loosen (do not remove) 2
screws on each side and lift
off blower housing
Remove left side
panel and disconnect
blower wires
Convection Blower
& Housing
5 5 Service Parts Replacement
2. Combustion Blower
PART NUMBER: 812-4400
a. Turn down thermostat, let appliance completely cool
and then unplug appliance before servicing.
b. The convection blower is located at the bottom rear
of the appliance and is housed inside a screen box.
Remove the 2 screws facing forward in the center of
the blower chamber at the very back of the appliance.
c. If an outside air kit is installed on the appliance, these
screws attach the intake air channel piece of the
outside air kit to the appliance. Remove the 2 screws
and pull backwards on the channel and it will slide
down and away from the appliance. The air channel,
collar and outside air hose will be removed as one
piece.
d. There are 2 screws on each side of the housing.
Loosen all 4 screws, but do not remove them. Lift
the blower housing up slightly and slide towards you
(Figure 25.3).
e. Remove the left side panel by loosening 2 screws
(do not remove) and pull side panel away. Unplug
the 2 black blower wires by disconnecting the spade
connectors.
f. To remove blower from the housing, remove 2 screws
in the front of the housing and very carefully bend the
2 housing sides out and bend the back of the housing
away from the blower. This allows for room to access
the back 2 screws and nuts (4 total) that is securing
the blower to the housing.
g. Remove blower and replace with new blower.
h. Re-install in reverse order.
a. Turn down thermostat, let appliance completely cool
and then unplug appliance before servicing.
b. Remove both side curtains by loosening 2 screws (do
not remove) and pull side panels away.
c. Remove 4 screws from the back screen and pivot
the top of the screen toward you leaving the bottom
attached to appliance (Figure 25.1).
d. Remove 2 screws to remove the thermostat block
and disconnect the 2 yellow wires.
e. Remove the 2 screws from the power inlet and rotate
it through the hole and out of the screen, leaving the
wires attached.
f. Disconnect the vacuum hose and both wires (orange
and red) from the vacuum switch attached to the rear
screen.
g. Remove both wires from exhaust blower (blue and
double white).
h. Remove 6 screws using a athead screwdriver or a
1/4” nut-driver. Retain screws for use on replacement
blower (Figure 25.2).
i. Remove exhaust blower and gasket.
j. Install new gasket and blower. Discard blower housing
if not needed.
k. Re-install in reverse order.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Quadra-Fire Castile - Pellet bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Quadra-Fire Castile - Pellet in de taal/talen: Engels als bijlage per email.

De handleiding is 8.11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Quadra-Fire Castile - Pellet

Quadra-Fire Castile - Pellet Gebruiksaanwijzing - Français - 40 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info