782214
14
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
Please note in general:
Proxxon bits and cutters have been designed to work
with our machines, which makes them optimal for
their use.
We will not assume any liability whatsoever for the
safe and proper function of our devices when using
third-party bits and cutters!
5.4 Adjusting the grinding table angle
(fig. 5):
Caution:
Before adjusting the grinding table, always discon-
nect the mains plug to prevent the disc being started
up accidentally. Risk of injury!
1. Loosen rotary knob 1 At the same hold rotary
knob 2
2. Swing grinding table 3 into the desired angle posi-
tion and check the set value on angle scale 4.
3. Tighten rotary knob 1. At the same hold rotary
knob 2
5.5 Connecting the dust exhaust (fig. 6):
Caution:
Before connecting the dust exhaust, always discon-
nect the mains plug to prevent the disc being started
up accidentally. Risk of injury!
It is recommended to always work with the dust
exhaust! This not only guarantees clean working, it
also reduces the hazardous effect of some dusts!
1. Push adapter piece 1 onto connecting piece 2 of
the machine
2. Push rubber adapter 3 onto adapter piece 1
3. Insert vacuum cleaner nozzle 4 into rubber
adapter 3
4. Switch on vacuum cleaner when working
Another small tip:
When using the Proxxon CW-matic vacuum cleaner,
manual switching on and off is no longer necessary.
The CW-matic is fitted with an automatic control
device; it automatically switches on and off when the
power tool is switched on and off. The same effect
can be obtained with traditional vacuum cleaners by
using our vacuum control device.
6 Working with the TG 125/E disc grinding
machine
Caution:
Please note that the grinding disc turns to the left! If
you use the left side when working with the attached
grinding table, the work piece can be guided easily
and securely, thus effectively preventing it from being
hurled away!
Caution:
When grinding metallic work pieces, such as when
grinding knife blades for example, or when grinding
stone or ceramics the material to be ground can
become very hot! Do not hold the material to be
ground near the grinding surface in order to avoid
burns!
Caution:
Wear suitable gloves to avoid abrasions especially
when working with coarse sandpaper and when pro-
cessing smaller work pieces!
1. If mitres are to be ground, adjust the grinding
angle as described above
2. Insert the mains plug
3. Switch on the machine at On-Off-Switch
4. Set the required speed on the speed control but-
ton (pos. 3, fig. 1)
Please adjust the size of the work piece to the size of
the machine! A work piece that is too large and too
heavy can overburden the drive or the construction of
the machine and cause damage or injuries!
6.1 Working with the angle stop (fig. 7):
If, for example, the ends of somewhat thinner strips
are ground for mitre, it is advantageous to use the
angle stop included in the scope of delivery.
1. Loosen knurled screw 1
2. Set the desired angle on scale 2
3. Turn the knurled screw tightly and insert into the
intended table groove
4. Guide the desired workpiece up to the stop
against the grinding wheel as shown in the illus-
tration
- 14 -
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Proxxon TG 125-E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Proxxon TG 125-E in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Turks, Deens, Zweeds als bijlage per email.

De handleiding is 3.16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info