78914
11
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
22 23
DRP 13-2 EQ DRP 13-2 EAQ
.............. 760 W ....................... 760 W
........... 0-600 min
-1
................0-600 min
-1
......... 0-1750 min
-1
.............. 0-1750 min
-1
......... 0-1100 min
-1
.............. 0-1100 min
-1
......... 0-3050 min
-1
.............. 0-3050 min
-1
.......... 1,5-13 mm ................. 1,5-13 mm
.........1/2"-20 UNF ...............1/2"-20 UNF
............. 1/4" mm .................... 1/4" mm
................ 13 mm .......................13 mm
................ 25 mm .......................25 mm
................ 45 mm .......................45 mm
................ 43 mm .......................43 mm
............... 2,0 kg ........................2,1 kg
................. II ........................... II
................ 81 dB (A) ...................81 dB (A)
................ 92 dB (A) ...................92 dB (A)
..................3 dB (A) .....................3 dB (A)
............... 1,2 m/s
2
.....................1,2 m/s
2
............... 1,5 m/s
2
.....................1,5 m/s
2
ENGLISH
ENGLISH
TOOL SPECIFICATION
Drill DRP 13-2 EQ/EAQ - Original instruction
Nom. power requirement ..........................................
Rated rpm 1st speed .................................................
Rated rpm 2nd speed ................................................
Rated rpm (no load) 1st speed ..................................
Rated rpm (no load) 2nd speed .................................
Drill chuck capacity range .........................................
Drill chuck thread ....................................................
Bit holder, hexagonal socket ......................................
Drill dia.
steel ....................................................................
aluminium ............................................................
wood ...................................................................
Clamping collar dia. ..................................................
Weight ...................................................................
Protection class ........................................................
Emission levels
L
pa
........................................................................
L
wa
.......................................................................
K .........................................................................
a
h
.........................................................................
K .........................................................................
Wear ear protectors!
Measured values determined according to EN 60 745.
NOTES ON SAFETY
This machine can only be operated safely when the
operating instructions and the pamphlet containing the
safety instructions have been completely read and
strictly adhered to.
For further notes on safety refer to enclosed Sheet.
Always inspect cable and plug before using machine.
Only have damage repaired by a qualied professional.
Make sure machine is switched off before inserting plug
in socket.
The machine must not be damp and must not be
operated in a wet environment.
Caution with long hair. Do not wear loose-tting
clothing while working.
Secure your workpiece with clamps.
Always direct power cable to rear away from the
machine.
When screwdriving, always operate in rst gear and
with low rpms.
Use caution when screwdriving long screws. Danger of
injury due to slipping off.
Always ensure that you have a secure footing while
working.
Always use the auxiliary handle if possible.
Watch out for the initial torque reaction of the drill,
especially when drill bit is tight.
Before carrying out any work on the machine
disconnect from power supply by removing plug from
socket.
When drilling with the impact activated use
hearing protection. Exposure to the effects of noise
may cause hearing loss.
Use the additional handle (additional handles) if
it is (they are) supplied with the tool. Loss of control
may cause injure people.
When carrying out an activity where the
machining tool could touch hidden power
conductors or its own power cord, hold the
electromechanical tool by the insulated surfaces.
Touching the machining tool with a "live" electrical
conductor may cause the exposed metal parts of the
electromechanical tool to become "live" and lead to
injury of the user by electric shock.
INTENDED USE
The machine is intended drilling in wood, metal,
ceramic and plastic. Machines with electronic control
and right/left rotation are also suitable for screwing
and thread cutting.
The user alone is responsible for any liabilities caused
by usage other than intended.
MAINS CONNECTION
Ensure that the voltage of the power supply matches
the information on the type plate of the power tool.
Tools with a rating of 230 V can also be connected to a
220 V/240 V supply.
EC-DECLARATION OF CONFORMITY
Drill Serial no.
DRP 13-2 EQ 631147
DRP 13-2 EAQ 631148
We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents. EN 60745-1, EN 55014-1,
EN 55014-2, EN 61000-3-2, EN 61000-3-3,
EN 60 745-2-1 in accordance with the regulations
2006/42/EC, 2004/108/EG.
All the procedures were applied as validly amended at
the time of the issue of this declaration, without
quoting these.
Technical documentation is kept at the manufacturer.
Stanislav Jakeš
10
ADVICE FOR OPERATION
Incorrect operation can lead to damage of the unit.
Therefore always observe the following
recommendations:
Sharp drill bits optimize performance whilst minimizing
wear on the machine.
Do not place such loads on the machine that it ceases
to turn.
When putting a high load on the machine, always set
the speed selector thumbwheel to the maximum speed.
After long periods at low operating speed, run the drill
at high speed and without load for approx. 3 minutes,
in order to cool the machine down.
MAINTENANCE
Periodically clean the ventilation slots on the motor
housing.
After an operating period of approx. 200 hours, the
following maintenance work must be performed:
Check the motor brushes and replace if necessary.
Clean the motor housing.
Renew the grease lling of the gearbox.
When the carbon brushes are worn out, the machine
switches itself off. The machine must then be sent to
customer service for maintenance (see enclosed
sheet).
GUARANTEE
Our equipment is under warranty for at least 12
months with regard to material or production faults in
accordance with national legislation. In the EU
countries, the warranty period for exclusively private
use is 24 months (an invoice or delivery note is
required as proof of purchase).
Damage resulting from, in particular, normal wear and
tear, overloading, improper handling, or caused by the
user or other damage caused by not following the
operating instructions, or any fault acknowledged at
the time of purchase, is not covered by the warranty.
Complaints will only be acknowledged if the equipment
has not been dismantled before being sent back to the
suppliers or to an authorised PROTOOL customer
support workshop. Store the operating instructions,
safety notes, spare parts list and proof of purchase in a
safe place. In addition, the manufacturer‘s current
warranty conditions apply.
We reserve the right to make changes to the technical
data contained in this information as a result of
ongoing research and development work.
Environmental Protection/Disposal
Power tools, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools
into household waste!
According to the European Directive 2002/96/EC on
waste electrical and elec tronic equipment and its
incorporation into national law, power tools that are no
longer suitable for use must be separately collect ed
and sent for recovery in an environmen tal-friendly
manner.
REACh
REACh is a European Chemical Directive that came into
effect in 2007. As “downstream users” and product
manufacturers, we are aware of our duty to provide
our customers with information. We have set up the
following website to keep you updated with all the
latest news and provide you with information on all the
materials used in our existing products: http://www.
tts-protool.com/reach
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Protool DRP 13-2 EQ bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Protool DRP 13-2 EQ in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info