490643
15
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
15
- Switch the power tool off immediately if
the tool insert gets jammed. Be prepared
for high torque levels if the tool kicks
back. The tool insert jams if:
- the power tool becomes overloaded or
- the tool tilts in the workpiece
- To mark the machine, do not drill into the
housing. The protective insulation would
be bridged. Use stickers.
- Never use the machine with a damaged
cable. Do not touch the damaged cable and
pull the mains plug when the cable gets
damaged during operation. Damaged ca-
bles increase the risk of electric shock.
Sliding clutch
- Always assume a safe standing position
and hold the power tool securely in both
hands. If the drill jams unexpectedly, the
machine kicks back.
- If the tool insert becomes caught or is
jammed, the drive to the drill spindle is
interrupted. Remove the load from the
machine immediately by retracting the
drill.
WARNING
If the power tool jams, switch the
machine off and release the tool in-
sert. When switching the machine on
with the drilling tool jammed, high
reaction torques can occur.
Residual risk
Although this information sheet and the
operating manuals for our electrical tools
contain extensive instructions on safe work-
ing with electrical tools, every electrical tool
involves certain residual risks that cannot
be completely prevented through safety
mechanisms. Therefore, electrical tools
must always be operated with the neces-
sary caution.
4.7 Noise / Vibration Information
Measured values determined according to
EN 60 745.
Typically the A-weighted noise levels of the
tool are:
Sound pressure level: 91 dB (A).
Sound power level: 102 dB (A).
Inaccuracy of measurement K = 3 dB (A).
CAUTION
The noise created during work may
damage hearing.
Use hearing-protective aids!
The typical hand-arm vibration is below
24.2 m/s
2
.
Inaccuracy of measurement K = 2.5 m/s
2
.
The typical hand-arm vibration is below
18.6 m/s
2
.
Inaccuracy of measurement K = 1.5 m/s
2
.
Declared total value of vibrations was
measured according to standard measure
method and can be used for comparison
one powertools with the others.
Declared total value of vibrations can be
used for preliminary setting of exposition.
Warning:
Emission of vibrations during real operating
can be different from declared total value of
vibrations depending on speci c real condi-
tions.
To protect operating person shell be provide
safety measurement, that evaluate the ex-
position under the real conditions (here are
included all parts of operating cycle, switch
of mode and idle run mode).
5 Application
The rotary/chiseling hammer can be used
universally for impact drilling, for light chis-
elling work in masonry and for drilling as well
as screwdriving in wood, metal and plastic.
This product does not fall under the com-
petency of directive 00/14/EC, article 12,
point 4.
6 Activation
WARNING
Before performing any maintenance
work on the tool, always remove the
plug from the electrical mains socket.
Check that the information on the manufac-
turing label complies with the actual power
supply voltage.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Protool CHP 26 PLUS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Protool CHP 26 PLUS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 13,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info