553942
20
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
20
MAINTENANCE AND TROUBLESHOOTING
Inspect and tighten all parts of the elliptical exerciser
r
egularly. Replace any worn parts immediately.
To clean the elliptical exerciser, use a damp cloth and
a small amount of mild soap. IMPORTANT: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
HOW TO ADJUST THE DRIVE BELT
If the pedals slip while you are pedaling, even while
the resistance is adjusted to the highest setting, the
drive belt may need to be adjusted.
To adjust the drive belt, see assembly steps 8 and 9
on pages 9 and 10 and remove the Left Pedal Leg
(24) and the Left Link Arm (25).
Then, see EXPLODED DRAWINGAnear the end of
this manual and remove the M6 x 25mm Button Screw
(61) from the center of the left Crank Arm Cover (32),
and then carefully remove the left Crank Arm Cover.
Note: You may have to remove a decal from the Crank
Arm Cover before you can remove the Button Screw.
Next, remove all the screws from the left shield, and
then carefully remove the left shield.
Loosen, but do
not remove, the
three M6 x 25mm
Button Screws
(61). Insert the
shaft of a screw-
driver downward
between the Idler
(12) and the pul-
ley located on the
Eddy Mechanism
(10). Pull the top
of the screwdriver
toward the rear of
the elliptical exerciser until the Belt (68) is tight, and
then tighten the three screws.
Reattach the left shield and the left crank arm cover.
Then, see assembly steps 8 and 9 on pages 9 and 10
and reattach the left pedal leg and the left link arm.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
To adjust the reed switch, first see EXPLODED
DRAWINGA near the end of this manual and loosen
the M6 x 25mm Button Screw (61) in the center of the
right Crank Arm Cover (32), and then carefully rotate
the right Crank Arm Cover out of the way.
Locate the Reed Switch (21). Loosen, but do not
remove, the indicated M4 x 16mm Screw (72). Slide
the Reed Switch slightly closer to or away from a
Magnet (18) on the Pulley (13).
Then, retighten the M4 x 16mm Screw (72). Turn one
of the Crank Arms (31) for a moment. Repeat until the
console displays correct feedback.
When the reed switch is correctly adjusted, replace
the crank arm cover.
21
18
13
72
31
10
61
12
68
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pro-form 490 STRIDE CLIMBER - PFEL04909 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pro-form 490 STRIDE CLIMBER - PFEL04909 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info