677792
3
Verklein
Vergroot
Pagina terug
1/58
Pagina verder
1
WIRELESS REAR VIEW CAMERA SYSTEM
WITH MIRROR DISPLAY & BLUETOOTH 2.1
HAND FREE SYSTEM
KABELLOSES INNENSPIEGEL RÜCKFAHR-
KAMERA-SYSTEM & BLUETOOTH 2.1
CAMERA DE RECUL SANS FILS & KIT
MAIN-LIBRE BLUETOOTH 2.1
DRAADLOOS CAMERASYSTEEM
& BLUETOOTH 2.1
With built-in 2.4 inch / 6,1 cm monitor
mit integriertem 2.4” / 6,1 cm Monitor
Avec écran 2.4’’ / 6,1 cm pouces intégré
met 2.4 inch / 6,1 cm monitor
APB220
2
INTRODUCTION
The Pro-User APB220 is member of the family of advanced car Rear view mirror back up
& Bluetooth 2.1 hand free systems manufactured by Pro User International Ltd.
The Pro-User Wireless Rear view mirror Back-up Camera & Bluetooth 2.1 hand free
systems, when used as described, will improve your ability to see behind your car,
camper, trailer, or mini-van. We have taken numerous measures in quality control to
ensure that your product arrives in top condition, and will perform to your satisfaction.
Please carefully read and follow the following safety and operating instructions.
IMPORTANT SAFETY AND PRIVACY
Before You Install
If you are not confident working with 12 volt DC vehicle wiring, removing and reinstalling
interior panels, carpeting, dashboards or other components of your vehicle, contact the
vehicle’s manufacturer, or consider having the camera system professionally installed.
Interference
All wireless devices are susceptible to interference or may cause interference, which
could affect usability.
Privacy
Upon detection of new mobile device (different ID) pairing, the Bluetooth system will
automatically erase all information concerning the previous linked mobile device,
including download phonebook, call log, etc.
Repair
The camera system should not be opened. Any attempt at modification or repair by the
user will entail the loss of your guarantee.
BEFORE using the Rearview Vehicle Back-Up Camera with Bluetooth® Hands-
Free Speakerphone System, please read the following safety information.
ALWAYS use the system as outlined here.
WARNING:
• A failure to read and follow these warnings and instructions may result in a serious
accident, including damaged property or a serious injury, including loss of life.
• The Rearview Mirror Vehicle Back-Up Camera with Bluetooth® Hands-Free
Speakerphone System is designed as an aid to the driver in detecting large stationary
objects to help avoid damaging the vehicle. However, you, the driver, must use it safely
and properly. Use of the Rearview Mirror Vehicle Back-Up Camera with Bluetooth®
Hands-Free System is not a substitute for safe, proper and legal driving.
• Never back up while looking only at the screen. You should always check behind and
around the vehicle when backing up just as you would if the vehicle did not have the
Rearview Mirror Vehicle Back-Up Camera with Bluetooth® Hands-Free Speakerphone
System. Always make sure your intended path is clear. If you back up while looking
only at the monitor, you may hit a vehicle, pedestrian, bicyclist, child, pet or other
object resulting in injury or death. Always back up slowly.
• Never depend on the Rearview Mirror Vehicle Back-Up Camera with Bluetooth® Hands-
Free Speakerphone System entirely when backing up. The image on the screen is
different from actual conditions. Objects viewed in the rear view monitor differ from
actual distance because a wide-angle lens is used. Objects in the rear view monitor will
appear visually opposite than when viewed in the rear view and outside mirrors. Use
3
the inside mirror or glance over your shoulder to properly judge distances to other
objects.
• The Rearview Mirror Vehicle Back-Up Camera with Bluetooth® Hands-Free
Speakerphone System’s “night vision” feature is an aid to a driver but is limited. Always
use your own eyes to confirm the vehicle’s surroundings, as the displayed image may
be faint or dark, distorted, or not entirely visible. Always check behind and all around
the vehicle visually and with mirrors before proceeding.
• The area displayed by the Rearview Mirror Vehicle Back-Up Camera with Bluetooth®
Hands-Free Speakerphone System is limited. The Rearview Mirror Vehicle Back-Up
Camera with Bluetooth® Hands-Free Speakerphone System does not display objects
that are close to or below the bumper, underneath the vehicle, or objects out of the
camera’s field of view. The area displayed on the screen may vary according to vehicle
orientation or road conditions.
• The Rearview Mirror Vehicle Back-Up Camera with Bluetooth® Hands-Free
Speakerphone System is not intended for use during longer backing maneuvers or
backing into potential crossing traffic or pedestrians. Crossing traffic or pedestrians may
be approaching outside of the camera’s field of view.
• Be sure to check the camera’s position and mounting angle before each use.
• Make sure the trunk, hatch, or backdoor is completely and securely closed when
backing up.
• If the back of the vehicle is hit, the position and mounting angle of the Rearview Mirror
Vehicle Back-Up Camera with Bluetooth® Hands-Free Speakerphone System may
change.
• When washing the vehicle with high pressure water, be sure not to spray it around the
camera. Otherwise, water may enter the camera unit causing water condensation on
the lens, a malfunction, fire or an electric shock.
• Do not strike the camera. It is a precision instrument. Otherwise, it may malfunction or
cause damage resulting in a fire or an electric shock.
• This product will only provide images of items that are within the field of view of the
camera. Thus, it is imperative that the camera should be kept clean and unobstructed,
and should mounted so that its field of view includes the entire area behind your vehicle.
• Distracted driving is dangerous. Always use the Bluetooth® Device in a manner that
does not reduce your attention and ability to drive carefully and safely.
• Adhere to all applicable traffic laws and motor vehicle regulations applicable to the
device.
• Consult local laws and regulations for any restrictions on installation or use.
• Never allow children to play with the device. Small parts may be a choking hazard.
4
PARTS
1. Rear View Mirror 2. Camera with mounting plate
3. Transmitter Box 4. Mounting Accessories 5. Mirror cigarette DC plug
6Transmitter Box Power Cable 7.Mirror mounting magic tape 8. Mirror power cable
INSTALLATION
These instructions do not apply to all vehicles. They are only meant as a general
guide due to the number of different makes & models. For vehicle specific
questions contact your vehicle’s manufacturer.
Camera installation
There are several ways to mount the camera on the back of your car. But the most
convenient is to mount it near the license plate of the car. Supplied is one mounting plate
that can be fixed behind the license plate, and the mounting plate have been installed in
the camera.
The camera is tiltable, camera angle can be adjusted manually on vertical direction.
Make
sure that its field of view and detection are not obstructed.
At some type of cars it is not possible to mount the camera near the license plate. You
may have to find another spot at the back of your car to mount the camera.
5
1. Remove the rear license plate, and then loosen the license plate bolts/screws.
2. Position the supplied mounting plates (with camera together) behind the license plate
bracket. Secure both license plate bracket and mounting plates with the license plate
bracket bolts/screws.
3. Mount the license plate on the license plate bracket.
4. Choose a routing path for the camera’s power cable through the vehicle’s body to the
reverse light circuit. If in doubt, seek professional installation assistance.
5. Some vehicles may have a hole available to pass the wire through, such as where the
license plate light is mounted, or you can drill a hole close to where the power cable
is attached to the camera. Once you have chosen where the cable will enter the
vehicle’s body, remove the camera. If you are able to use an existing opening, skip
the next two steps.
6. Before you drill a hole you MUST CHECK and see WHAT IS BEHIND WHERE YOU ARE
DRILLING. If there are any vehicle components, such as electrical parts or fuel
system components behind where you are drilling, you must take whatever
precaution is necessary not to damage them. Remove the license plate and camera
before drilling.
7. After you have drilled the hole, insert the supplied grommet, then pass the camera
cables through the grommet into the vehicle. You must use the grommet to prevent
the metal edge of the hole from cutting the camera cable.
8. Mount the transmitter box inside the trunk. Connect the camera’s power cable and
the transmitter box power cable to the transmitter box.
9. Next you’ll need to find the vehicle’s reverse lights. Turn the vehicle’s ignition key to
the accessory position, engage the parking brake and put the car in reverse. Look at
the vehicle’s tail lights to see where the reverse lights are located, they are the white
lights. To locate the reverse light’s 12V+ wire it will be necessary to gain access to
6
the rear of the vehicle’s tail light. For help locating the vehicle’s reverse light circuit
contact your vehicle’s manufacturer for
vehicle specific wiring diagrams.
10. Once you have located the reverse light
circuit you will have to route the
transmitter box power cable to that
location. You must securely fasten the
power cable to prevent it from being
caught on any vehicle component such
as the trunk hinge. Never route the
cable on the outside of the vehicle!
11. The reverse light sockets on most
vehicles have two wires connected to
them. Usually the negative wire is black
and the positive wire is a colored wire.
If you are uncertain about the wiring,
you can use a 12 volt multimeter
available at most auto parts stores to determine which is the positive wire. Follow the
manufacturer’s instructions for the safe use of the multimeter.
12. After determining which wire is the positive and which is the negative, turn off the
ignition key, then remove the battery’s negative cable.
13. Splice the red wire using the supplied in-line wire connectors to the reverse light’s
positive (+) wire. Use a set of slip joint pliers to squeeze the TAP and insure good
connection.
14. Next splice the black wire of the transmitter box power cable to the reverse light’s
negative (-) wire or ground.
15. Replace the reverse light bulb, and then re-install the light socket. Secure all the
wires with cable ties or electrical tape.
16. Re-attach the negative battery cable to the battery.
Rear View Mirror Installation
When mounting the mirror, please double check the width of your car’s rear view mirror
80mm to avoid cannot be installed.
1. Place the spring loaded top clips underneath the car’s existing rear view mirror.
7
2. Press down the mirror extend to the bottom clips, then tilt the mirror towards the
existing rear view mirror.
3. Left the spring loaded clips close around the mirror. Adjust the Rear View Mirror for
the best rear view.
4. Tighten the magic tape to fix the position.
Remark: Please make sure the male and female of the magic tape are matched perfectly
before you connect the metal buckle of the magic tape to the main unit, once you
connect them, you can not pull the metal buckle out.
8
5. Choose a Location and Install Power Cable as below alternative methods showed in
the pics:
a. Choose a location on windshield or dashboard of your car, where does not obstruct
your vision.
b. Insert the small 12 Volt DC plug of the power cable into the top of the mirror.
c. Connect the Cigarette DC plug cable (provided) with the cigarette lighter socket/12V
power outlet of vehicle.
Remark: The cable must not interfere the safe operation of the vehicle.
9
For professional installation, refer to the illustration above, if doubt please seek
professional assistant.
NOTE: UNDER EXTREME BRIGHT LIGHT CONDITIONS, THE SCREEN IMAGE MAY TAKE A
FEW SECONDS TO STABLIZE. PLEASE WAIT UNTIL THE IMAGE HAS STABLIZED BEFORE
BACKING UP.
Back up System testing
1 Reattach the vehicle’s negative battery cable.
2 Turn the ignition key to the accessory position, do not start the vehicle.
3 Engage the parking brake, and then put the shifter in the reverse position.
After testing the unit and you are satisfied with the route you have chosen for the cabling,
you must permanently install it.
Route all wires behind interior panels or under carpeting so they are hidden. Use supplied
cable ties to neatly gather any excess wire.
10
OPERATION
There are 6 control buttons available for users to have their controls:
A. Power ON/OFF
• APB220 will automatically turn ON when it is connected to a power source
• Hold
to turn APB220 ON/OFF
• When turned ON, APB220 will enter search mode Connecting to look for known
Bluetooth devices
• To search again, press
once to activate search mode
• When the vehicle is in reverse gear, APB220 automatically enter back up mode
NOTE: For automatic Bluetooth connection, please make sure Bluetooth mode on your
mobile phone is activated and you must have successfully paired and connected to
APB220 at least once in order to activate this feature.
Make sure the Bluetooth is off before parking for safe operation.
B. Pairing/Linking
Pairing Bluetooth enables devices like mobile phones to work with the APB220 Rearview
Mirror Speakerphone. This step only needs to be performed once.
Before Pairing the APB220 Bluetooth Speakerphone:
• Ensure the Bluetooth on your mobile phone is activated
• Ensure the APB220 Rearview Mirror Speakerphone is plugged into a 12V power source
Follow the steps below to pair your APB220 with your mobile phone:
• Power ON the APB220
• Press and hold M for 2 seconds
• Screen will indicate Pairing Mode
NOTE: APB220 is now in pairing mode
• Activate the Bluetooth settings of your mobile phone
NOTE: The following steps are general procedure; to access Bluetooth Menu for your
mobile phone, please refer to your phone user manual.
• Select SET-UP or CONNECT from your mobile phone menu
11
Connected
(Phone’s ID)
• Find and select OPTION to discover Bluetooth devices; establishing a connection may
take several minutes
• If found, phone display should indicate APB220 device was detected or Select “APB220”
from the list
• Phone should give you a prompt asking if you want to pair the device
• Select OK or ACCEPT and wait for prompt to enter passkey or PIN
• Enter the code 0000
• Select “OK” to pair and connect the APB220 and the hands
• When pairing is complete, the APB220’s LCD will show
NOTE: The APB220 can pair with more than one phone, however it can only connect to
one phone at a time. If you wish to pair to a second phone, disable or turn OFF Bluetooth
on the phone already paired.
NOTE: If the APB220 and mobile handset did not successfully pair, follow the steps below
to retry pairing:
• Turn the APB220 OFF & ON
• Turn OFF all other Bluetooth devices before starting the pairing process
• Repeat the pairing instructions from the beginning
To Link APB220 to your mobile phone after pairing:
• Press
of your APB220 or
• Establishing the connection via your mobile phone
NOTE: Make sure Bluetooth has been activated on your mobile phone before you press
(Please refer to your mobile’s operation manual about connecting Bluetooth devices)
C. Phonebook
APB220 Rearview Mirror Speakerphone can store up to 950 phone numbers. If you are
trying to transfer 1100 contacts to the APB220, only the first 950 contacts will be
successfully transferred.
AT Command function can automatically transfer the contacts in your mobile phone to
the APB220 Rearview Mirror Speakerphone.
NOTE: Not all mobile phones support AT Command features, please refer to your phone
manual to determine if phone supports one of these.
Phonebook Set-up via AT Command
To transfer the Phonebook from your mobile phone via AT Command:
• Make sure the APB220 and mobile phone is connected
• Press M and Contacts will appear on the screen
• Press
to enter the sub-menu
• Press +/- to select Download Contact and press to confirm
• LCD will display
• Once transfer is successful, LCD will display
Completed
Total XXX
p
b
Lo
ading
...
T
o
t
a
l
XXX
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pro-User APB220 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pro-User APB220 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info