481024
7
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
POWXQ5390 EN
Copyright © 2015 VARO P a g e | 7 www.varo.com
medical implants consult their doctor and the manufacturers of the implants before
operating this device.
8 TRANSPORT AND START OF OPERATION
8.1 Transport and set-up
The machine must be set up indoors. Upon installation, the workplace must provide
satisfactory conditions for the proper performance of technical work.
The installation surface must be sufficiently level and load-bearing. If required, the
machine can be fastened down to the installation surface.
Due to packaging technical reasons the machine comes not fully assembled.
8.2 Assembly
If you discover transport damage while unpacking the machine inform your dealer
immediately. Do not use the device!
Please dispose of the packaging in an environmentally-friendly way.
Remove the anti-corrosive grease from the saw table using a mild solvent.
8.3 Assembly of clamping jig handle (J) (Fig. 2)
8.4 Release of the saw head
The machine comes fitted with a locked saw head as standard. The lock bolt of the saw head
(Q) can be removed. Let the saw head slide slowly upward. (Fig. 3)
When transporting the machine the saw head must be locked in place again.
8.5 Key storage
Put the supplied key (T) in the holder on the rear of the saw. (Fig. 4)
8.6 Electrical connection
The mains power supply and the extension cable used must meet the stipulated
regulations.
The mains supply and the frequency must agree with the data provided on the machine
rating plate.
The device must be protected by a 10 A fuse.
Only use a mains cable with the designation H07RN-F.
Connections and repair of electrical equipment may only be carried out by qualified
electricians.
8.7 Start of operation
Press switch (A) on D-handle (B) to start the device: As soon as you release the switch the
machine will shut off.
9 OPERATING THE MACHINE
9.1 Correct working position:
Stand in front of the machine in the direction of the cut.
9.2 Handling the work piece:
The work piece to be cut must be firmly held in the clamping jig, so that it cannot move
during the cutting process.
Always secure the work piece between angle plate (G) and clamping jig pressure plate
(H). ( Fig. 5)
Do not cut undersized work pieces.
Support long work pieces with roller blocks.
Large, round or irregularly shaped work pieces must have additional clamping
arrangements. Use G-clamps and blocks to firmly hold the work piece in place.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWXQ5390 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWXQ5390 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Powerplus POWXQ5390

Powerplus POWXQ5390 Gebruiksaanwijzing - Nederlands - 15 pagina's

Powerplus POWXQ5390 Gebruiksaanwijzing - Deutsch - 13 pagina's

Powerplus POWXQ5390 Gebruiksaanwijzing - Français - 13 pagina's

Powerplus POWXQ5390 Aanvulling / aanpassing - Alle talen - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info