517142
8
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
POWXG1006 EN
Copyright © 2015 VARO P a g e | 8 www.varo.com
9.2 Tensioning the saw chain
Always pull the plug out of the power socket before doing any work on the
chainsaw!
Wear safety gloves!
Make sure the saw chain (4) is inside the guide groove of the guide bar (7) (Fig.1 a)!
Turn the outer Knob clockwise until the saw chain is correctly tensioned, then rotate the inside
knob (5) to block the guide bar in that position.
While the inside knob is being tightened, the guide bar must then be pushed upwards.
Check the chain tension again (see Fig. 3). Do not tension the chain too tightly.
When cold, it should be possible to lift the chain in the middle of the guide bar approx. 5 mm.
Tighten the lock nut (5) securely.
When warm, the saw chain will expand and slacken and there is a danger of it jumping off the
rail altogether. Re-tension if necessary.
If the saw chain is re-tensioned when hot, it must be loosened again when the sawing work
has been completed. Otherwise, the contraction which takes place as the chain cools would
result in excessively high tension.
A new saw chain requires a running-in period of approx .5 minutes. Chain lubrication is very
important at this stage. After running in, check chain tension and re-tension if necessary.
9.3 Filling in chain oil (Fig 4)
To prevent dirt getting inside the tank, clean the oil tank cap (21) before opening. Check the
contents of the oil tank during sawing work by checking the oil gauge (15). Close the oil tank
cap tightly and wipe away any spills.
9.4 Securing the extension lead (Fig 6)
Only use extension leads suitable for outdoor use. The cross section of the cable (max. length
of extension cord: 75m) must be at least 1,5 mm². secure the chainsaw flex to the extension
lead by inserting the extension lead into the strain relief gap of the housing.
Extension leads longer than 30 m will reduce the performance of the chainsaw.
9.5 Chain lubrication
To prevent excessive wear, the saw chain and guide bar must be evenly lubricated during
operation.
Lubrication is automatic. Never work without chain lubrication. If the chain runs dry, the entire
cutting apparatus will quickly become severely damaged. It is therefore important to check
both chain lubrication and the oil gauge every use (Fig. 4).
Never use the saw when the oil level is below the Min. mark.
Min.: When only approx. 5 mm of oil is visible at the lower rim of the oil gauge (15), you
must top up with oil.
Max.: Top up with oil until the window is full.
9.6 Checking the automatic lubrication
Before commencing work, check the automatic chain lubrication and oil gauge. Switch on the
chain saw and hold it above the ground. Be careful not to allow the chain saw to touch the
ground. For safety reasons it is best to keep a clearance of at least 20 cm. If you now see
growing traces of oil, the chain lubrication system is working correctly. if there are no traces of
oil at all, try cleaning the oil outlet (Fig 2, C), the upper chain tensioning borehole (E) and the
oil duct, or contact your Customer Service.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Powerplus-POWXG1006

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWXG1006 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWXG1006 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWXG1006

Powerplus POWXG1006 Gebruiksaanwijzing - Nederlands - 15 pagina's

Powerplus POWXG1006 Gebruiksaanwijzing - Deutsch - 15 pagina's

Powerplus POWXG1006 Gebruiksaanwijzing - Français - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info