645723
9
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
POWX1340 EN
Copyright © 2015 VARO P a g e | 9 www.varo.com
8.2 Sharpening the chain
Set your saw on a flat, solid surface. For proper sharpening the chain tension should be
adjusted (as specified in the chainsaw instruction manual). Sharpening will be best
accomplished if done on the flat of the saw bar somewhere near the middle of the bar.
Position the saw so that you are looking at the side of the chain bar with the motor to your
right. Cutter teeth on the far side of the chain are sharpened, from inside to outside as
shown in figure 5. Lay the guide (B) flat on the tooth with the 30° index line (L) parallel
with the chain. Align the index line with the chain. Two or three light strokes are usually
enough unless the cutters have been damaged. Sharpen all cutters equal. Start with the
cutter with the most visual damage (i.e. nicks or gouges) and sharpen all cutters equally.
Do not remove excessive material as this only shorten the life of the chain.
Sharpen cutter teeth (J) only, not the depth gauge (K)
When all of the teeth on the top of the bar have been sharpened, advance the chain using
a glove or a rag by pulling the chain toward the end of the bar. Repeat until all the teeth
on the far side of the chain have been sharpened.
Turn the saw around so you are looking at the side of the chain bar with the motor to your
left. Sharpen the cutter teeth on the far side of the chain, from inside to outside, or away
from you (figure 6). Lay the guide flat on the tooth with the 30° index line parallel with the
chain. Repeat the process above to sharpen all of the cutter teeth on the far side of the
chain.
After your chain has been sharpened a number of times, you may fin that it does not cut
as fast as you feel it should. Each cutter on your chain has a depth gauge (K) just ahead
of the cutting edge (J) that determines how big a bite it can take. To check for proper
depth of the cut, lay a metal straight edge across the tops of the cutting edges (Figure 7),
and check the dimension indicated. This dimension should be approximately equal to the
thickness of the gauge (K). if it is not, grind the chain depth gauge until the clearance is
approximately equal to the thickness of the sharpening kit gauge. Be careful to maintain
its shape. Do not remove more material. Houd de instelling van de dieptemaat gelijk bij
alle zaagtanden, om rechte zaagsneden te kunnen maken.
9 OPERATION
9.1 On / off switch (Pic. 3)
Always check that the power supply corresponds to the voltage on the
rating plate.
Turning on: Turn the power button to position I
Turning off:Turn the power button to position O
9.2 Setting the speed (Pic. 4)
The multi tool speed is continuously adjustable. Always start from the lowest speed and
then increase the speed to the desired level.
“+” denotes the higher speed
-” denotes the lower speed
9.3 LED light (Pic. 5)
If you work in dark condition and want see clearly the work area ,please turn on the LED
Push the LED button (6),the LED is on
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX1340 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX1340 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWX1340

Powerplus POWX1340 Gebruiksaanwijzing - Nederlands - 13 pagina's

Powerplus POWX1340 Gebruiksaanwijzing - Deutsch - 14 pagina's

Powerplus POWX1340 Gebruiksaanwijzing - Français - 13 pagina's

Powerplus POWX1340 Aanvulling / aanpassing - Alle talen - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info