480958
7
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
POWX131 EN
Copyright © 2015 VARO P a g e | 7 www.varo.com
Never use the spindle lock to stop the motor.
9.2 Marking the workpiece s.
Before starling with the biscuit jointer the work pieces must be marked as following:
Place the two work pieces. Which must be connected, on top of each other.
Fasten the work pieces and mark the center of the groove.
The space between two grooves should be 10-15cm. This is not applicable for smaller
Work pieces- smaller work pieces don't have to be marked
9.3 Positioning of the machine
Based on the size of the work pieces the machine can be positioned in several ways.
9.4 Large wqpkpieces:
Place the machine near the work piece
The middle of the base plate (this point is marked on the base plate) must face the center
of the groove in the work piece, {see marking the work piece).
9.5 Small workpieces.
Place the machine near the work piece
The side of the machine must be lacing the side of the work piece.
9.6 Sawing grooves
Move the motor base backward.
Place the machine near the work piece.
Position the machine (see positioning of the machine)
Hold the machine with both hands and switch the machine on.
Push the motor base carefully forward as far as possible.
Move the motor base backward and switch the machine off.
9.7 Joining the workpieces
When the grooves in both work pieces have been made the workplaces can be joined together
Put glue in both grooves.
Race the biscuit dowel in the groove of one work piece.
Place the other work piece on the biscuit dowel.
Fasten the work pieces and wait till the glue is dry.
9.8 Checking the cutting depth
Always check the cutting depth after mounting a saw blade.
Disconnect the plug from the socket.
Move the motor base (14} as far as possible backwards.
Set the cutting depth in the maximum position by turning the depth adjustment knob (6).
Move the motor base forwards till the pin will fall in the notch of the adjustment knob (6)
Turn the saw blade till one tooth of the saw blade is in the front position.
Measure the distance from the side of the base plate to the tooth of the saw blade.
Check if the distance is 19mm. The maximum position is 18mm.
9.9 Setting the cutting depth
When the cutting depth is not correct, II can be adjusted as following:
Move the motor base (14) as far as possible backwards
Loosen the Pin
Sell the cutting depth by luring the screw, the screw is positioned at the back of the pin.
Repeat the procedure till the cutting depth is correct.
Fasten the Pin.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Powerplus-POWX131

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX131 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX131 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWX131

Powerplus POWX131 Gebruiksaanwijzing - Nederlands - 11 pagina's

Powerplus POWX131 Gebruiksaanwijzing - Nederlands - 11 pagina's

Powerplus POWX131 Gebruiksaanwijzing - Deutsch - 11 pagina's

Powerplus POWX131 Gebruiksaanwijzing - Français - 11 pagina's

Powerplus POWX131 Aanvulling / aanpassing - Alle talen - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info