675035
8
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
POWX07582 EN
Copyright © 2017 VARO P a g e | 8 www.varo.com
9.1 Installation
Get help from another person for lifting the machine out of the box.
Turn the turntable into the 0° position and tighten up the mitre locks.
Note: If the machine must be mounted on a workbench, then the rubber feet should NOT be
installed.
You run the risk of injury, if you handle the machine incorrectly when lifting
or turning it. Always hold the machine firmly by the base (12).
Position the machine on a suitable surface:
All 4 feet must rest firmly on the surface.
The ideal height of the surface is approximately 800 mm.
The saw must stand firmly in position, even when larger workpieces are being sawn.
You can keep the packaging for future use, or you can dispose of it separately, based on
the type of material, and it in an environmentally friendly manner.
9.2 Transport
Push the table saw downwards and at the same time pull out the locking knob (22) to lift
the table saw upwards.
Position the lower saw blade guard (14) over the saw guide piece (21) and push
backwards until you hear a click, and until the lower saw blade guard is positioned at the
black line on the saw guide piece.
Lower the saw head by pushing in the safety lock (6) and activate the locking pin (22).
Position the mitre guide (4) over the lower saw blade guard and fasten it.
Lift the machine up by grasping both sides of the base (12).
Note:
The essential operating components of the machine are presented in this section.
Make sure to read this section, before you use the machine for the first time.
9.2.1 Table saw operating mode
Make sure that the table is mounted completely and in the right direction see Paragraph
9.2 on Transport above - and that the locking pin (22) is properly locked.
Remove the mitre and width guide (4).
Install the saw blade guard (3) by sliding the back into the slot on top of the riving knife (2)
and backwards to lock. Mount the lower saw blade guard (14) by pushing the back of the
saw blade guard into the back of the opening of switch B (29)until the front of the lower
blade guard (14) is aligned with the reference points on the insert (21).
The ON/OFF switch (7) is used for starting and stopping the machine.
9.2.2 Cross-cut and mitre saw operating mode
Make sure that the mitre and width guide (4) is correctly installed and that the saw blade is
covered. This activates switch A (8). Make sure that the cover (mitre and width guide) is
firmly attached. If this is not the case, use the mitre and width guide locking knob (5) to
fasten it.
Push the table saw downwards and at the same time pull out the locking knob (22) to lift
the table saw upwards.
Remove the lower saw blade guard (14).
For starting the motor, push on the switch (29) in the handgrip.
To switch off the motor, release the switch (20).
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX07582 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX07582 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWX07582

Powerplus POWX07582 Gebruiksaanwijzing - Nederlands - 22 pagina's

Powerplus POWX07582 Gebruiksaanwijzing - Deutsch - 22 pagina's

Powerplus POWX07582 Gebruiksaanwijzing - Français - 21 pagina's

Powerplus POWX07582 Aanvulling / aanpassing - Alle talen - 5 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info