582665
6
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
POWX0682 EN
Copyright © 2014 VARO P a g e | 6 www.varo.com
If the blades come in contact with the work piece before they reach full speed, it could
cause the saw to kickback toward you resulting in serious injury.
7 ASSEMBLY
7.1 Attaching the handle
Screw handle into saw (fig 1).
Use nut to tighten the handle.
7.2 Removing the blades
Be sure to first unplug the electric cord from the electrical outlet and allow
blades to cool before removing the blades.
Push the spindle lock to secure the blade (Fig 2).
Use the blade wrench to unscrew the lock nut (Fig 3).
Remove lock nut from the blade (Fig 4).
Open lower guard of the blade (Fig 5).
Lift up and remove “Face B” blade (Fig 6).
Lift up and remove “Face A” blade (Fig 7).
7.3 Attaching the blades
Identify “Face A” and “Face B” on your new set of DUALSAW blades (Fig 8).
Open lower guard and place “Face A” blade on saw and fit on the outer arbor shaft (Fig 9).
Place “Face B” blade on top of “Face A” blade and fit on inner arbor shaft (Fig 10).
Place lock nut onto shaft (Fig 11).
Tighten lock nut using blade wrench tool (Fig. 12).
8 OPERATION
8.1 Operating the saw
Push lock button and press the on/off trigger. Always let the blades reach full speed before
you begin to cut into the work piece.
Apply steady and even pressure when making a cut. Forcing the saw causes rough cuts
and could shorten the life of the saw or cause kickback.
Always feed material parallel to the blade. Feeding at an angle can burn the blade and
damage the blade teeth.
To stop the saw, release trigger.
8.2 Switching ON/OFF
To turn on the machine, push the ON/OFF switch in the ON position.
To turn the machine off, push the ON/OFF switch into the OFF position.
Inrush currents can cause short-time voltage drops; under unfavorable power supply
conditions, other equipment may be affected (if the system impedance of the power supply
is lower than 0,127 + j0,079 Ohm, disturbances are unlikely to occur); if you need further
clarification, you may contact your local power supplier.
8.3 Feed speed
Feed speed is how quickly you push the saw blades through the material being cut. The
correct feed speed is totally determined by the hardness and the thickness of the material
being cut.
If the feed speed is too slow the blades will only press down the material rather then cutting it.
The blade edges glide an wear down the material, what causes a poor cut and will cause
excessive wear on the blades.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX0682 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX0682 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Powerplus POWX0682

Powerplus POWX0682 Gebruiksaanwijzing - Nederlands - 12 pagina's

Powerplus POWX0682 Gebruiksaanwijzing - Deutsch - 12 pagina's

Powerplus POWX0682 Gebruiksaanwijzing - Français - 12 pagina's

Powerplus POWX0682 Aanvulling / aanpassing - Alle talen - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info