Handleiding Powerplus POWE51101 (pagina 3 van 14) (Engels)

675010

Verklein

Vergroot

Pagina terug

1/14

Pagina verder

  POWE51101  EN 
Copyright © 2019 VARO  P a g e  | 1  www.varo.com 
APPLICATION ................................................................................... 3 
DESCRIPTION (FIG. A) ..................................................................... 3 
PACKAGE CONTENT LIST .............................................................. 3 
SYMBOLS .......................................................................................... 4 
GENERAL POWER TOOL SAFETY WARNINGS ............................ 4 
1  Working area ............................................................................................................. 4 
2  Electrical safety ......................................................................................................... 4 
3  Personal safety ......................................................................................................... 5 
4  Power tool use and care ........................................................................................... 5 
5  Service ....................................................................................................................... 5 
SAFETY EQUIPMENT ....................................................................... 6 
1  Cleaving wedge ......................................................................................................... 6 
2  Saw blade protector .................................................................................................. 6 
3  Push stick .................................................................................................................. 6 
UNPACKING AND ASSEMBLY ........................................................ 6 
1  Assembly (Fig. 1) ...................................................................................................... 6 
2  Attaching the tilt protection (Fig. 2) ......................................................................... 6 
3  Fitting the parallel fence (Fig. 3) ............................................................................... 6 
4  Mounting mitre angle stop (Fig. 4) ........................................................................... 7 
5  Mounting the saw blade guard (Fig. 5) .................................................................... 7 
6  Mounting the extraction hose (Fig. 6) ...................................................................... 7 
OPERATION ...................................................................................... 7 
1  Check before starting the device! ............................................................................ 7 
2  Operating elements ................................................................................................... 7 
2.1  On/off switch ............................................................................................................... 7 
2.2  Overload Protection (18) ............................................................................................. 7 
2.3  Setting mechanism for the tilt angle ............................................................................. 8 
2.4  Hand crank for setting the cutting height ..................................................................... 8 
3  Workpiece stops ....................................................................................................... 8 
3.1  Mitre angle stop .......................................................................................................... 8 
3.2  Mitre cuts (Fig. 7) ........................................................................................................ 8 

  POWE51101  EN 
Copyright © 2019 VARO  P a g e  | 2  www.varo.com 
3.3  Setting the stop rail of the parallel stop ........................................................................ 8 
3.4  Parallel stop ................................................................................................................ 8 
4  Setting the cutting height (Fig. 8) ............................................................................. 8 
5  Setting the saw blade angle (Fig. 8) ......................................................................... 9 
6  Sawing ....................................................................................................................... 9 
CLEANING AND MAINTENANCE .................................................. 10 
1  Cleaning and maintenance overview ..................................................................... 10 
2  Cleaning the device ................................................................................................ 10 
3  Unit maintenance .................................................................................................... 10 
3.1  Fitting and changing the saw blade (Fig. 9) ............................................................... 11 
3.2  Adjusting the cleaving wedge (Fig. 10) ...................................................................... 11 
STORAGE, TRANSPORTATION .................................................... 11 
1  Storage .................................................................................................................... 11 
2  Transportation ......................................................................................................... 11 
TECHNICAL DATA .......................................................................... 12 
NOISE ............................................................................................... 12 
WARRANTY ..................................................................................... 12 
ENVIRONMENT ............................................................................... 13 
DECLARATION OF CONFORMITY ................................................ 14 
 

POWE51101 EN

TABLE SAW 2200W

POWE51101

1 APPLICATION

The device is designed to cleave and-cross-cut solid wood, laminated wood, chipboard, wood

core plywood and similar wooden materials. Round pieces may not be sawed as the rotating

saw blade may cause them to roll. Only those materials may be processed for which the

particular saw blade is designed. Only saw blades suitable for the unit (carbide and chrome

vanadium blades) may be used. The use of high-speed steel blades and cutting wheels of any

type is not permitted. The unit may not be used in areas where there is an explosion hazard.

Not suitable for professional use.

WARNING! For your own safety, read this manual and the general safety

instructions carefully before using the appliance. Your power tool should

only be given to other users together with these instructions.

2 DESCRIPTION (FIG. A)

1. On switch I (green)/ Off switch 0

(red)/ emergency stop

2. Saw blade height and tilt angle

adjustment (crank)

3. Locking knob of the saw blade

(rotary knob)

4. Cut angle indicator

5. Extraction hose

6. Table extension

7. Saw blade guard

8. Cleaving wedge

9. Bracket

10. Locking lever for parallel stop

11. Mitre angle stop

12. Parallel stop

13. Base frame

14. Push stick

15. Open-ended spanner

16. Tilt protection

17. Rubber feet

18. Overload protection

3 PACKAGE CONTENT LIST

▪ Remove all packaging.

▪ Remove remaining packing and packing inserts (if included).

▪ Check that the package contents are complete.

▪ Check the appliance, the power cord, the power plug and all accessories for transportation

damage.

▪ Keep the packaging until expiration of the warranty period. Then take it to your local waste

disposal system.

WARNING: Packaging materials are not toys! Children must not play with

plastic bags! There is a danger of suffocation!

Bench circular saw with

saw blade

Blade guard

Saw bench

2 saw bench extenders

8 brackets

Parallel fence

Angle fence

Push-stick

2 spanners for blade

change

Bag with small parts

Vacuum hose

Hose nozzle

2 tilt protection devices

4 supporting legs

Operating Instructions

Hex key

If any parts are missing or damaged, please contact your dealer.

POWE51101 EN

4 SYMBOLS

The following symbols are used in this manual and/or on the machine:

Denotes risk of personal

injury or damage to the tool.

Read manual before use.

Conforms to essential safety

standards of applicable

European directives.

Wear noise protection.

Wear eye protection.

Keep hands away from

blades, Don’t touch the blades

when starting or while

operating the unit.

Wear a mask in dusty

conditions!

Class II - The machine is

double insulated; Earthing

wire is therefore not

necessary.

5 GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and instructions. Failure to heed warnings and follow instructions

may result in electric shock, fire and/or serious injury. Keep safety warnings and instructions

for future reference. The term "power tool" in the safety warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless) power tool.

5.1 Working area

▪ Keep working area clean and well lit. Untidy and dark areas can lead to accidents.

▪ Do not operate power tools in potentially explosive surroundings, for example, in the

presence of inflammable liquids, gases or dust. Power tools create sparks that may ignite

the dust or fumes.

▪ Keep children and bystanders at a distance when operating a power tool. Distractions can

cause you to lose control of it.

5.2 Electrical safety

Always check that the power supply corresponds to the voltage on the

rating plate.

▪ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

adapter plugs with earthed power tools. Unmodified plugs and matching outlets will reduce

the risk of a lethal electric shock.

▪ Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and

refrigerators. There is an increased risk of a lethal electric shock if your body is earthed.

▪ Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will

increase the risk of a lethal electric shock.

▪ Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or tangled

cords increase the risk of a lethal electric shock.

▪ When operating a power tool outdoors, use an extension cable suitable for outdoor use.

Using a cord suitable for outdoor use reduces the risk of a lethal electric shock.

▪ If operating a power tool in a damp location is unavoidable, use a power supply protected

by a residual current device (RCD). Using an RCD reduces the risk of a lethal electric

shock.

POWE51101 EN

5.3 Personal safety

▪ Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or

medication. A moment of inattention when operating a power tool may result in serious

personal injury.

▪ Use safety equipment. Always wear eye protection. Using safety equipment such as a

dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed

will reduce the risk of personal injury.

▪ Avoid accidental starts. Ensure the switch is in the off position before inserting the plug.

Carrying power tools with your finger on the switch or plugging in power tools when the

switch is in the on position makes accidents more likely.

▪ Remove any adjusting keys or spanners before turning on the power tool. A spanner or

key left attached to a rotating part of the power tool may result in personal injury.

▪ Do not reach out too far. Keep your feet firmly on the ground at all times. This will enable

you to retain control over the power tool in unexpected situations.

▪ Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from the power tool. Loose clothes, jewellery or long hair can become

entangled in the moving parts.

▪ If there are devices for connecting dust extraction and collection facilities, please ensure

that they are attached and used correctly. Using such devices can reduce dust-related

hazards.

5.4 Power tool use and care

▪ Do not expect the power tool to do more than it was designed to do. Use the correct power

tool for what you want to do. A power tool will achieve better results and be safer if used in

the circumstances for which it was designed.

▪ Do not use the power tool if the switch cannot turn it on and off. A power tool with a broken

switch is dangerous and must be repaired.

▪ Disconnect the plug from the power source before making adjustments, changing

accessories, or storing power tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

▪ Store power tools when not in use, out of the reach of children and do not allow people

who are not familiar with the power tool or these instructions to operate it. Power tools are

potentially dangerous in the hands of untrained users.

▪ Maintenance. Check for misalignment or jammed moving parts, breakages or any other

feature that might affect the operation of the power tool. If it is damaged, the power tool

must be repaired. Many accidents are caused by using poorly maintained power tools.

▪ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to jam and are easier to control.

▪ Use the power tool, accessories and cutting tools, etc., in accordance with these

instructions and in the manner intended for the particular type of power tool, taking into

account the working conditions and the work which needs to be done. Using a power tool

in ways for which it was not intended can lead to potentially hazardous situations.

5.5 Service

▪ Your power tool should be serviced by a qualified specialist using only standard spare

parts. This will ensure that it meets the required safety standards.

POWE51101 EN

6 SAFETY EQUIPMENT

6.1 Cleaving wedge

The cleaving wedge (8) prevents a workpiece being caught by the ascending teeth and being

thrown against the operator. The cleaving wedge must remain in place during operation.

6.2 Saw blade protector

The saw blade guard (7) protects the user from accidentally touching the saw blade and from

flying splinters. The saw blade protector must always remain in place during operation.

6.3 Push stick

The push stick (14) serves as an extension of the hand and protects the user from accidentally

touching the saw blade. The push stick must always be used when the gap between the stop

and the saw blade is less than 120 mm.

7 UNPACKING AND ASSEMBLY

Unpack the unit and make sure all of the pieces are there.

Lower the saw blade underneath the table surface (see 8.4 Setting cutting height)

Turn the saw table up-side down

Note: If any of the parts is missing or damaged contact the retailer.

7.1 Assembly (Fig. 1)

First attach L and R table extensions to the table saw (without the brackets)

Mount the base frame and attach it to the table saw

The base frame (13) consists of four table legs with cross braces that must be mounted.

Required tools:

2 combination spanners

▪ Attach the four table legs (19) to the corners of the saw table. Note that the legs on the

rear must be mounted so that the holes for the assembly of the tilt protection devices face

the rear of the machine.

▪ Mount the cross braces A on the front and rear between legs 13.

▪ Mount the cross braces A on the sides between legs 13.

Do this by attaching each cross brace on the inside to each table leg with two screws, washers

and locking nuts.

▪ Push the rubber feet (17) onto the supporting legs.

▪ Finally, fit the four brackets 21 with the table extension and the table legs.

The brackets (21) are fitted through the screw holes in the housing.

Note: Only place the device on a level, skid-proof surface. The device must

not wobble.

7.2 Attaching the tilt protection (Fig. 2)

▪ Bolt the tilt protection to the rear supporting legs using bolts (A), washers, spring washers

and nuts.

7.3 Fitting the parallel fence (Fig. 3)

Insert the parallel fence (12) into the rail of the measuring scale. Check the setting at the

window. Push the locking lever (10) downwards to lock the parallel fence (12) into place. In

order to obtain a perfectly parallel cut, you should check the gap between the fence and the

saw blade at two positions using a meter rule.

POWE51101 EN

7.4 Mounting mitre angle stop (Fig. 4)

The mitre angle stop (11) consists of two parts - the stop plate (A) and the angle adjustment

(B) that must be assembled together.

▪ Insert the stop plate (A) into the gaps of the angle adjustment (B) with both adjusting

screws (C), push into the required position and tighten the adjusting screws.

Push the gliding bar (D) of the mitre angle stop into the required bar of the table surface.

Right-handed operators prefer to push the mitre angle stop into the left bar

of the table surface.

7.5 Mounting the saw blade guard (Fig. 5)

Risk of injury! The saw blade must be at least set to 30mm height.

▪ First, mount the crank (2).

▪ Put the blade in the highest position.

▪ Position the saw blade protection on the cleaving wedge (8) so that bolt (22) engages in

the hole. Then attach the wing nut.

7.6 Mounting the extraction hose (Fig. 6)

▪ Place the vacuum hose (5) on the connecting piece of the saw blade guard (7).

▪ Put the vacuum hose (5) on the vacuum connecting piece (23) on the rear of the device

8 OPERATION

Risk of injury! In the event of a functional fault, immediately press the red

button 0 on the On / Off switch and unplug.

8.1 Check before starting the device!

Risk of injury! The device may only be put into operation if there are no

defects. If a part is defective danger it must be replaced before the device is

used again.

Check to make sure the device is in safe operating condition:

▪ Check to make sure there are no visible defects.

▪ Check to make sure all device components are correctly mounted.

▪ Check to make sure the safety equipment is functioning properly.

▪ Check to make sure that the saw blade runs freely.

▪ Check whether the adjusting screw for setting the angle of tilt is tightened.

8.2 Operating elements

8.2.1 On/off switch

▪ Switching on: Pressing the green button I on the On / Off switch (1) switches on the saw.

Before starting to saw, wait until the blade has reached maximum speed.

▪ Switching off: Pressing the red button 0 on the On / Off switch (1) switches off the saw.

8.2.2 Overload Protection (18)

The machine is fitted with an overload protection (18). Allow the machine to cool down for at

least 30 minutes before switching it on again. For this first press the black button next to the

switch, then press the green button (1) to restart the machine.

POWE51101 EN

8.2.3 Setting mechanism for the tilt angle

The saw blade can be adjusted to any angle between 0° and 45°. Loosen the locking knob (3),

press the lever (2) and turn to the desired tilt angle and tighten the locking knob (3).

8.2.4 Hand crank for setting the cutting height

The cutting height of the saw blade must be adjusted to the height of the workpiece. The saw

blade must always be set to one blade tooth higher than the workpiece. You can set this by

turning the hand crank to left or right.

Note: In order to make use of the full range of 45° settings, the cutting

height must be reduced accordingly.

8.3 Workpiece stops

8.3.1 Mitre angle stop

The stop can be adjusted by a maximum of 120 mm for mitre cutting.

Risk of injury! Do not push the stop (Fig. 4 A) too far in the direction of the

saw blade. The gap between the stop (Fig. 4 A) and the saw blade should be

approximately 2 cm.

8.3.2 Mitre cuts (Fig. 7)

▪ Push the mitre angle stop (11) into the required slot of the table surface.

▪ Loosen adjusting screw (A), set the required angle and then tighten the adjusting screw

again.

▪ If necessary, push the stop plate backwards or forwards. For this, loosen both adjusting

screws (B), push stop plate (C) and then retighten adjusting screws (B).

8.3.3 Setting the stop rail of the parallel stop

The stop rail can be removed and repositioned after both wing nuts have been loosened:

High stop edge:

▪ To saw tall workpieces.

Low stop edge:

▪ To saw flat workpieces.

▪ If the saw blade is angled.

8.3.4 Parallel stop

▪ Loosen the locking lever (10) by turning the knob.

▪ Set the parallel stop to the required cutting width by pushing on the scale.

▪ Press down the locking lever (10).

8.4 Setting the cutting height (Fig. 8)

Risk of injury! Parts of the body or objects located in the adjustment area

may be caught by the operating saw blade! Only adjust the cutting height

when the saw blade is at a standstill!

▪ Adjust the cutting depth by turning the hand crank (A).

POWE51101 EN

▪ Turning the hand crank counterclockwise reduces the cutting depth. Turning the hand

crank clockwise Increases the cutting depth.

Note: To balance out play in the cutting height setting, always raise the saw

blade from below to the required position.

The cutting depth is optimally set when the saw blade is one blade tooth

higher than the wofkpiece.

8.5 Setting the saw blade angle (Fig. 8)

Risk of injury! Parts of the body or objects located in the adjustment area

may be caught by the operating saw blade! Only adjust the blade angle

when the saw blade is at a standstill!

▪ Loosen the fixing screw (3).

▪ Set the required angle of tilt.

▪ The set tilt angle can be read from the scale (4).

▪ Tighten the fixing screw (3).

Notes: In order to make use of the full range of 44° settings, the cutting

height must be reduced accordlngry.

8.6 Sawing

Risk of injury! If the gap between the parallel stop and the saw blade is less

than 120 mm, the push stick must be used.

Risk of injury! Always hold the guided workpiece, not the section of

workpiece that is being cut off.

Machine damage

Check the wood to be processed carefully. Foreign objects such as nails,

screws and other similar objects may seriously damage the unit

▪ Set the required gap of the parallel stop to the saw blade

▪ Set the required angle of the cross stop.

▪ Set the saw blade cutting height.

▪ Set the required tilt angle of the saw blade.

▪ Place the workpiece up against the cross stop.

▪ Switch the circular saw bench on by pressing the green button I on the On / Off switch (1).

▪ Push the workpiece evenly towards the back and saw in a single process. Make sure that

the saw Is not overloaded.

▪ Use the red button 0 on the On / Off switch (1) to switch the unit off if you are not going to

continue working immediately.

POWE51101 EN

9 CLEANING AND MAINTENANCE

9.1 Cleaning and maintenance overview

Prior to each use

What?

How?

Check the saw blade to ensure it is

correctly positioned and fixed in place.

Changing the saw blade

Check the saw blade protector box for

wood chippings/saw dust Remove

chippings if necessary.

Use compressed air to blast the

chippings/dust out or use a brush.

Check that the gap between the saw blade

and the cleaving wedge is set to 3 to 5

mm; correct if necessary.

Adjusting the cleaving wedge

Check the connection cable for any signs

of damage

Conduct a visual inspection and have the

cable replaced by an electrician if

necessary.

Regularly and according to operating conditions

What?

How?

Screw connections

Check all screw connections and tighten if

necessary.

Clean the ventilation slots on the motor to

remove dust

Use a vacuum or a brush to remove the

chippings/dust.

9.2 Cleaning the device

Risk of electric shock! Never splash with water or expose to water. Never

use detergents or solvents to clean. These may cause irreparable damage

to the unit The plastic pieces may be corroded by the chemicals.

Careful treatment and regular cleaning will ensure that the unit remains functional and

performs well for a long time.

▪ Remove dirt with a brush.

▪ Wipe the tool with a damp cloth.

▪ Keep ventilation slots clean and free of dust

9.3 Unit maintenance

Risk of injury! Before conducting any maintenance work make sure the

device is unplugged (disconnect the power supply).

Risk of injury! Shortly after sawing, the saw blade may be very hot. Allow a

hot blade to cool down. Never dean a hot saw blade with flammable liquids.

A still saw blade can cause injury! Use gloves to change the saw blade.

POWE51101 EN

9.3.1 Fitting and changing the saw blade (Fig. 9)

Caution! Unplug from power source.

Caution! Ensure that the saw housing is well lit.

▪ Remove the screw (24) of the front of the table insert.

▪ Remove the table insert

▪ Use the crank and turn to the left to bring the saw blade as far up as it will go.

▪ Use the spanners (15) to remove the screw on the saw blade (Fig. 9) and exchange the

blade with a suitable replacement. Watch the direction of operation! See the arrow on the

saw blade. The teeth must point towards the on/off switch (1).

9.3.2 Adjusting the cleaving wedge (Fig. 10)

The gap between the external edge of the saw blade and the cleaving wedge (8) must be

between three and five millimetres.

▪ Bring saw blade angle to the 0° position and tighten.

▪ Bring the saw blade into the upper position.

▪ Remove the saw blade protector.

▪ Remove the table surface.

▪ Loosen the screw (A) slightly with a suitable combination spanner until the cleaving wedge

(8) is released (do not remove screw)

▪ Set the cleaving wedge lower or higher by pushing upward or downward in the long hole.

▪ Mount all dismantled parts in reverse sequence.

10 STORAGE, TRANSPORTATION

10.1 Storage

Risk of injury! Store the unit in such a way that it cannot be started by

unauthorised persons. Ensure that no one is able to injury themselves on

the stored unit.

Machine damage! Do not store unprotected in a damp environment.

10.2 Transportation

Note: Only lift the unit using the handles.

▪ Crank the saw blade down as far as it will go.

▪ Parts that extend beyond the saw should be removed.

▪ Transport the unit with the assistance of another person and use the handles.

▪ When dispatching, try to use the original packaging, if possible.

POWE51101 EN

11 TECHNICAL DATA

Rated Voltage

220-240 V

Rated Frequency

50 Hz

Rated Power

S1:1800W S6 20% 2200W

Weight

20 kg

Protection class

Degree of protection

IP20

Rotation speed

5000 min-1

Diameter of saw blade (external)

255 mm

Saw blade hole (internal)

30 mm

Saw blade thickness

2.8 mm

Number of teeth

24T

Max. cutting depth at 90°

85 mm

Max. cutting depth at 45°

65 mm

Table size

640 x 485 mm

Table height (+stand)

829 mm

Dust extraction outlet

Ø 35.5mm

12 NOISE

Noise values measured according to relevant standard. (K=3)

Acoustic pressure level LpA

97 dB(A)

Acoustic power level LwA

110 dB(A)

ATTENTION! The sound power level may exceed 85 dB(A), in this case

individual hearing protection shall be worn.

13 WARRANTY

▪ This product is warranted as provided by law for a 24 -month period effective from the

date of purchase by the first user.

▪ This warranty covers all material or production flaws excluding : batteries, chargers,

defective parts subject to normal wear & tear such as bearings, brushes, cables, and

plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects

resulting from maltreatment, accidents or alterations; nor the cost of transportation.

▪ Damage and/or defects resulting from inappropriate use also do not fall under the

warranty provisions.

▪ We also disclaim all liability for any bodily injury resulting from inappropriate use of the

tool.

▪ Repairs may only be carried out by an authorised customer service centre for Powerplus

tools.

▪ You can always obtain more information at the number 00 32 3 292 92 90.

▪ Any transportation costs shall always be borne by the customer, unless agreed otherwise

in writing.

▪ At the same time, no claim can be made on the warranty if the damage of the device is the

result of negligent maintenance or overload.

▪ Definitely excluded from the warranty is damage resulting from fluid permeation, excessive

dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate

usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not

following the instructions given in the manual), inexpert assembly, lightning strike,

erroneus net voltage. This list is not exhaustive.

POWE51101 EN

▪ Acceptance of claims under warranty can never lead to the prolongation of the warranty

period nor commencement of a new warranty period in case of a device replacement.

▪ Devices or parts which are replaced under the warranty therefore remain the property of

Varo NV.

▪ We reserve the right to reject a claim whenever the purchase cannot be verified or when it

is clear that the product has not been properly maintained. (Clean ventilation slots, carbon

brushes serviced regularly, etc.).

▪ Your purchase receipt must be kept as proof of date of purchase.

▪ Your appliance must be returned undismantled to your dealer in an acceptably clean state,

(in its original blow-moulded case if applicable to the unit), accompanied by proof of

purchase.

14 ENVIRONMENT

Should your appliance need replacement after extended use, do not dispose of it

with the household refuse, but in an environmentally safe way.

Please dispose of used motor oil in a manner that protects the environment. We

suggest you take it in a sealed container to your local service station for recycling.

Do not throw it into the refuse or pour it on the ground

POWE51101 EN

15 DECLARATION OF CONFORMITY

VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that,

product: Table saw

trade mark: PowerPlus

model: POWE51101

is in conformity with the essential requirements and other relevant provisions of the applicable

European Directives, based on the application of European harmonized standards. Any

unauthorized modification of the apparatus voids this declaration.

European Directives (including, if applicable, their amendments up to the date of signature);

2011/65/EU

2014/30/EC

2006/42/EC

European harmonized standards (including, if applicable, their amendments up to the date of

signature);

EN61029-1: 2009

EN61029-2-1: 2012

EN55014-1: 2006

EN55014-2: 2015

EN61000-3-2: 2014

EN61000-3-3: 2013

Keeper of the Technical Documentation : Philippe Vankerkhove, VARO – Vic. Van Rompuy

N.V.

The undersigned acts on behalf of the company CEO,

Hugo Cuypers

Certification Manager

17/10/18

Powerplus POWE51101 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Powerplus POWE51101

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info