795637
9
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
POWDP4050 EN
Copyright © 2021 VARO P a g e | 9 www.varo.com
To install the belt proceed in reverse order.
10.3 Planing
Choose the desired cutting depth before operation.
Hold the planer with one hand on the switch and the other hand on the adjustment knob
(2).
Place planers shoe on the surface to be planed. Making certain that the cutting blades are
not touching the surface.
Push down firmly on the adjustment knob of the planer. So that the planers base is
completely flat on the work piece surface. Depress the lock-off button and push the trigger
switch. Allow the motor to reach full speed before starting to plane.
Move the tool slowly over the work piece and maintain downward pressure to keep the
planer flat. Be particularly careful to keep the tool flat at the beginning and the end of the
work piece surface.
ATTENTION: Never change the cutting depth while operating , to not create any
irregularities on the planed surface.
10.4 Rebating (Fig. 8a & 8b)
Insert the screw provided through the slot on the rebate. Turn the screw into the nut on
the housing.
The cut depth adjustment can be set from 0 to 8 mm
To adjust the depth of cut, place the planer on a flat board, then loosen the screw and
slide the cut depth adjustment guide up and down for required depth.
Tighten the thumb screw fully.
The depth of rebating cut is determines by moving the rebate and the number of passes made
along the workpiece. Make sure that the planer is guided with a lateral supporting pressure.
10.5 Edge chamfering (Fig. 9)
Always use both hands on the tool for any operation. It assures to maintain
control and avoid risk of serious personal injury. The workpiece must
always be properly supported and clamped so that both hands will be free
to control the planer.
Using the V-groove is the base plate you can make a chamfer on the work piece edge.
Guide the planer along the edge and maintain a constant angle and force to produce a
good finish.
You can control the angle of the chamfer with your hands.
Make a test chamfer on a scrap piece of wood.
Maintain downward pressure to keep your planer flat at the beginning and the end of the
work surface.
10.6 Dust extraction
When using the planer dust will be generated.
Always use the dust bag supplied with your product.
The dust extraction outlet can be connected to an external vacuum cleaner to extract while
operating.
11 CLEANING AND MAINTENANCE
Attention !Before performing any work on the equipment, pull the power
plug.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWDP4050 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWDP4050 in de taal/talen: Engels als bijlage per email.

De handleiding is 0.35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWDP4050

Powerplus POWDP4050 Gebruiksaanwijzing - Nederlands - 13 pagina's

Powerplus POWDP4050 Gebruiksaanwijzing - Deutsch - 13 pagina's

Powerplus POWDP4050 Gebruiksaanwijzing - Français - 13 pagina's

Powerplus POWDP4050 Aanvulling / aanpassing - Alle talen - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info