685364
23
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
Starting and Stopping the PT-3000
CHECK BEFORE OPERATING THE ENGINE
If the engine is malfunctioning DO NOT operate until repairs
are made.
Be sure cover, guards and shields are in place before operating
the engine. Replace any that are damaged or missing.
Check to see that the area around the engine is clear of foreign
objects before starting.
DO NOT allow children or animals to approach the APU
while in operation.
DO NOT start the engine by shorting across starter terminals.
Engine starting controls
1) PT-3000 Main switch (located on the internal control panel on the APU) must
Be in ON position.
NOTE: This switch should be in the ON position except when performing
maintenance or to prevent starting for any reason.
2) Toggle the driver control panel switch to the ON position.
3) Glow plugs will preheat for 8 seconds. LED light flashes slowly.
4) Preheating will cease during engine cranking cycle. LED light continues flashing.
5) Engine begins an 8 second crank cycle, After 4 seconds of cranking the PT ECU-
64 will check for an AC signal from the generator. If an AC signal is verified the
engine will start and the LED will remain ON during the normal run operation. If
the AC signal is not verified the PT ECU-64 will terminate the cranking cycle and
LED light will flash a fault code.
6) Starter disengages immediately after engine run is verified.
7) PT ECU-64 deactivates the low Oil Pressure and high Water Temperature
switches for 6 seconds; this will assure oil pressure build up time. If oil pressure
does not build up the engine will immediately shut down and go into a fault mode.
Likewise for a high temperature situation.
8) If engine will not start on the first attempt the PT ECU-64 will initiate the start
cycle 2 more times before going into fault mode. Glow plugs will preheat for 8
seconds per attempt. Engine will crank for 8 seconds per attempt.
9) To shut down the engine under normal operations, push the driver control box
switch to the STOP position.
10) If a fault occurs during the normal operation of the PT-3000 the LED on the
driver control box will repeat a flashing code. This code will help troubleshoot the
problem. Count the flashes to determine the problem and refer to the service
manual for corrective procedures. The fault codes are as follows
LED Flashes 1 Time: Failure to Start
LED Flashes 2 Times: High Water Temperature
LED Flashes 3 Times: Low oil Pressure
LED Flashes 4 Times: No AC signal
20
23

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

PowerTech-PT-3000

Zoeken resetten

  • Nieuw aggregaat pt2000 start perfect maar komt geen stroom uit half jaar oud nog nooit gebruikt. Handleiding zoek geraakt. Zit er misschien een zekering? Gesteld op 10-7-2024 om 17:01

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw PowerTech PT-3000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van PowerTech PT-3000 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info