574062
92
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
Additional information
11
92
En
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, contact the Pioneer Service Center specified on your warranty card.
Power
No sound
Symptom Cause Remedy
The power does not turn on. • The power plug is disconnected. • Connect the power plug to the wall outlet.
• The protection circuit may have been
activated.
• Disconnect the power plug from the outlet, and insert
again.
• Something is obstructing the rear panel fan. • Unplug the amplifier from the wall and call the Pioneer
Service Center specified on your warranty card.
The amplifier suddenly switches
off.
• The speaker wires are frayed or sticking out
of the jack, and are touching the back of the
amplifier or another set of wires.
• Reinsert the speaker wires, making sure there are no
stray strands of wire and that they are inserted fully.
• The amplifier has a serious problem. • Unplug the amplifier from the wall and call the Pioneer
Service Center specified on your warranty card.
During loud playback the power
suddenly switches off.
• The protection circuit has been activated
because the lowest actual impedance of the
speakers (as opposed to the speakers rated
impedance) is dangerously low.
• Turn down the volume.
• When its convenient, go to Acoustic Calibration EQ on
page 55 and lower the 63 Hz and 125 Hz equalizer levels
using the manual setting.
• Turning the digital safety feature on may allow you to
turn up the volume a little more. To switch between
SAFETY 1 (medium effect), SAFETY 2 (more effect) and
SAFETY OFF, put theamplifier into standby, then press the
STANDBY/ON button while holding down the OPTION
button on the front panel. If the power switches off even
with SAFETY 2 switched on, turn down the volume.
AMP ERR blinks in the display,
then the power automatically
switches off.
• The amplifier has a serious problem. • After about a minute (you won’t be able to switch the
unit on during this time), switch the amplifier back on. If
the message persists, call the Pioneer Service Center
specified on your warranty card.
FAN STOP blinks in the display,
then the power automatically
switches off.
• Something is obstructing the fan located on
the underside of the unit.
• Unplug the receiver from the wall and call the Pioneer
Service Center specified on your warranty card.
• The fan is malfunctioning. • Unplug the receiver from the wall and call the Pioneer
Service Center specified on your warranty card.
OVERHEAT blinks in the display
and no sound is output.
• The internal temperature of the unit has
become too high.
• After allowing the unit to cool down in a well-ventilated
place, try switching the amplifier back on. Make sure you
follow the guidelines for improving heat dispersal in
Ventilation on page 2.
Symptom Cause Remedy
No sound is output when an
input source is selected.
• Improper connections. • Make sure you have properly connected the component
to the corresponding input on the back of the amplifier
(see Connecting your equipment on page 12).
• Sound is muted or the volume is turned
down.
• Press MUTE or adjust the volume accordingly.
• The TAPE 2 monitoring feature is on. Press TAPE 2 MONITOR to switch it off (see Monitoring
your recording on page 69).
• Speakers are turned off or selected
improperly with the SP SYSTEM A/B switch.
• Press SP SYSTEM A/B to select the proper speaker set
(see Switching the speaker system on page 75).
• The input signal type is incorrect. • Press SIGNAL SELECT to select the proper input signal
(see Selecting the input signal type on page 44).
• The i.LINK source selected for the main
room has also been selected as a source in
the sub room.
• Choose a different source or choose a different input
signal for the main room, such as DIGITAL or ANALOG
(see Selecting the input signal type on page 44).
92

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Pioneer-VSA-AX10i-S

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer VSA-AX10i-S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer VSA-AX10i-S in de taal/talen: Engels als bijlage per email.

De handleiding is 3,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Pioneer VSA-AX10i-S

Pioneer VSA-AX10i-S Gebruiksaanwijzing - Nederlands - 104 pagina's

Pioneer VSA-AX10i-S Gebruiksaanwijzing - Deutsch - 104 pagina's

Pioneer VSA-AX10i-S Gebruiksaanwijzing - English - 25 pagina's

Pioneer VSA-AX10i-S Gebruiksaanwijzing - Français - 104 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info