577805
118
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
118
FAQ
13
Symptom Remedy
Synchronized operation not possible
using Control with HDMI function.
Check the HDMI connections.
The cable may be damaged.
Select ON for the Control Mode with HDMI setting (see HDMI Setup on page 74 ).
Turn the TV’s power on before turning on this receiver’s power.
Set the TV side Control with HDMI setting to on (see TV’s operating instructions).
Connect the TV to the HDMI OUT 1 terminal and set the HDMI output to OUT 1. Then
turn on first the TV’s power, then this receiver’s power.
When HDZONE is set to ON, the
video resolution and number of
audio channels for the main zone
side changes.
This is due to the HDMI connection specifications; it is not a malfunction. When play-
ing the same input in the main zone and HDZONE, video and audio signals that can be
output in common for all the devices connected to the HDMI OUT 1, HDMI OUT 2 and
HDMI OUT 3 (HDZONE) terminals are set.
HDZONE cannot be turned on.
Set Output Setting at MAIN/HDZONE to HDZONE (page 108 ).
When the input source for the main
or HDZONE is switched or when
the power of the respective zones is
turned on and off, the audio or video
of the HDMI output terminal that is
not being operated is sometimes
interrupted.
This is because the HDMI devices need to recognize each other again. This is not a
malfunction. If the picture is disturbed or not displayed, turn off the power of the devices
in all the zones, then try again. Also try temporarily turning the Network Standby and
Standby Through settings OFF.
Such menus as the HOME MENU as
well as the on-screen display are not
displayed for HDMI OUT 1 or HDMI
OUT 2.
Press OUT P. and switch the HDMI OUT 1/2 setting.
Cannot upscale to 4K or 1080p.
Change V.CONV to ON. (page 80 )
Change RES. (page 80 )
When HDZONE is turned on, upscaling cannot be performed. To perform upscaling, turn
off HDZONE (page 84 ).
4K video is not output even though a
4K compliant TV is connected.
When the MAIN/HDZONE setting is MAIN and the HDMI output setting is OUT 1+2 and
when the MAIN/HDZONE setting is HDZONE and HDZONE is the same input as with the
main zone, video is output with the lower resolution of the TV connected to HDMI OUT 1
and HDMI OUT 2. When there is only one 4K compliant TV, connect it to HDMI OUT 1
and set the HDMI output setting to OUT 1 or turn off HDZONE so that video is only output
to the 4K compliant TV.
Even though a 4K/60p 4:4:4 24 bit
compatible TV is connected, the
4K/60p 4:4:4 24 bit video image is not
output correctly.
Set the HDMI 4K/60p signal output setting to 4:4:4 (page 83 ).
When the HDMI cable does not support 4K/60p 4:4:4 24 bit (18 Gbps transmission),
video images may not be output properly. In that case, replace the cable with a compat-
ible HDMI cable or change the HDMI 4K/60p signal output setting to 4:2:0 to watch the
4K/60p 4:2:0 24 bit video image.
The HDMI OUT 3 terminal does not output a 4K/60p 4:4:4 24 bit video image if
MAIN/HDZONE is set to HDZONE. Set MAIN/HDZONE to MAIN or use the HDMI OUT
1 or HDMI OUT 2 terminals.
You cannot input 4K/60p 4:4:4 24 bit video from HDMI IN 3 to the IN 7 terminal. Use the
BD IN, HDMI IN 1 or HDMI IN 2 terminal.
MHL
Symptom Remedy
When playing an MHL-compat-
ible device connected to the
HDMI 7/MHL terminal, the Standby
Through function does not work and
the power turns off.
The MHL device will not operate unless power is being supplied from this receiver. When
this receiver is in the Standby Through mode, power cannot be supplied due to reduced
power consumption. Because of this, the MHL device will not operate. This is not a mal-
function.
MHL-compatible device cannot be
operated with the remote control.
Press MHL to set the remote control to the MHL control mode.
MHL POW ERR is displayed on the
display.
There is a problem with the power supply for the MHL device. After turning OFF the
receiver, disconnect the MHL device, connect the MHL device again and then turn ON
the power of the receiver.
If the error is displayed even though the above operation is repeated several times,
there is a problem with the receiver or the MHL device. Disconnect the power cable and
request repair.
Built-in AVNavigator
Symptom Cause Remedy
AVNavigator does not interact well
with the receiver.
The receiver’s power is not turned
on.
Turn the receiver’s power on. (Wait about 60
seconds after the power turns on for network
functions to start.)
The receiver or computer is not con-
nected to the LAN.
Connect a LAN cable to the receiver or computer
(page 42 ).
The router’s power is off. Turn the router’s power on.
Network connections could be
restricted due to the computer’s net-
work settings, security settings, etc.
Check the computer’s network settings, security
settings, etc.
In the middle of Wiring Navi, you are
instructed to turn off the power of the
unit and then connect other equip-
ment or speakers.
This is to avoid failure of the receiver
due to a short-circuit between cables
or from static electricity.
Per the Wiring Navi instructions, turn OFF the
power of the receiver. As long as the browser has
not quit, Wiring Navi resumes guidance upon
turning ON the receiver.
When the Wiring Navi or
Interactive Operation Guide is
launched, a warning about security
protection appears on the browser.
This is because of the browser’s
security function.
This is not a problem. Perform the operation to
authorize the blocked contents.
AVNavigator screen is not displayed
on the browser.
This receiver’s IP address has not
been entered into the browser cor-
rectly.
Check the receiver’s IP address and enter it cor-
rectly in the browser (page 106 ).
Receiver settings cannot be made
from a browser.
JavaScript is disabled on the internet
browser.
Enable JavaScript.
The browser is not compatible with
JavaScript.
Use an internet browser that is compatible with
JavaScript.
 
118

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer SC-LX58-S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer SC-LX58-S in de taal/talen: Engels als bijlage per email.

De handleiding is 16,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Pioneer SC-LX58-S

Pioneer SC-LX58-S Snelstart handleiding - Nederlands - 76 pagina's

Pioneer SC-LX58-S Gebruiksaanwijzing - Nederlands - 145 pagina's

Pioneer SC-LX58-S Snelstart handleiding - Deutsch - 76 pagina's

Pioneer SC-LX58-S Gebruiksaanwijzing - Deutsch - 147 pagina's

Pioneer SC-LX58-S Snelstart handleiding - English, Français - 76 pagina's

Pioneer SC-LX58-S Gebruiksaanwijzing - Français - 144 pagina's

Pioneer SC-LX58-S Snelstart handleiding - Italiano - 76 pagina's

Pioneer SC-LX58-S Gebruiksaanwijzing - Italiano - 143 pagina's

Pioneer SC-LX58-S Snelstart handleiding - Espanõl - 76 pagina's

Pioneer SC-LX58-S Gebruiksaanwijzing - Espanõl - 143 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info