577805
116
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
116
FAQ
13
Settings
Symptom Remedy
The Auto MCACC Setup continually
shows an error.
The ambient noise level may be too high. Keep the noise level in the room as low as pos-
sible (see also Problems when using the Auto MCACC Setup on page 49 ). If the noise
level cannot be kept low enough, you will have to set up the surround sound manually
(page 102 ).
When using only one surround back speaker, connect it to the SURROUND BACK L
(Single) terminals.
To use a 5.1-channel speaker set, use the surround speakers for the surround channel,
not the surround back channel.
Make sure there are no obstacles between the speakers and the microphone.
If Reverse Phase is displayed, try the following:
— The speaker’s wiring (+ and –) may be inverted. Check the speaker connections.
— Depending on the type of speakers and their installation conditions, Reverse Phase
may be displayed even if the speakers are properly connected. If this happens, select
GO NEXT and continue.
— If the speaker is not pointed to the microphone (listening position) or when using
speakers that affect the phase (dipole speakers, reflective speakers, etc.), it may not be
possible to properly identify the polarity.
After using the Auto MCACC Setup,
the speaker size setting is incorrect.
There may have been some low frequency noise in the room from an air-conditioner,
motor, etc. Switch off all other appliances in the room and use Auto MCACC Setup again.
Depending on a number of factors (bass reproduction capabilities of the speakers, room
size, speaker placement, etc.) this may occur in some cases. Change the speaker setting
manually in Speaker Setting on page 103 , and use the ALL (Keep SP System) option for
the Auto MCACC menu in Automatic MCACC (Expert) on page 94 if this is a recurring
problem.
Can’t adjust the Fine Speaker Dis-
tance setting properly.
Check that the speakers are all in phase (make sure the positive (+) and negative (–)
terminals are matched up properly).
The display shows KEY LOCK ON
when you try to make settings.
With the receiver in standby, press u STANDBY/ON for about 5 seconds while holding
down SPEAKERS to disable the key lock.
Most recent settings have been
erased.
The power cord was disconnected from the wall while adjusting this setting.
Settings are only stored if all the zones are turned off. Turn off all the zones before
unplugging the power cord.
The various system settings are not
stored.
Do not pull out the power cord while conducting the settings. (The settings will be stored
when both the main zone and sub zone turn off. Turn off all zones before pulling out the
power cord.)
Certain listening modes or
HOME MENU items cannot be
selected.
When Operation Mode is set to Basic, the Pioneer-recommended settings are made and
not all of the functions can be used. To use all of the functions without restrictions, set
Operation Mode to Expert (see Operation Mode Setup on page 51 ).
Feels like there is no subwoofer EQ
effect.
The effect becomes less when the set frequency value of the crossover frequency is low.
When setting a high frequency value, the subwoofer EQ effect becomes stronger. How-
ever, setting a higher crossover frequency increases the share that the subwoofer bears
for low-frequency playback. For that reason, it is disadvantageous in terms of the phase
point of view. Set to your preference.
Professional Calibration EQ graphical output
Symptom Remedy
The reverb characteristics graph
after EQ calibration does not appear
entirely flat.
There are cases where the graph does not appear flat (even when selecting ALL CH ADJ
in the Auto MCACC Setup) due to adjustments made to compensate for room character-
istics to achieve optimal sound.
Areas of the graph may appear identical (before and after) when there is little or no
adjustment needed.
The graph may appear to have shifted vertically when comparing before and after mea-
surements.
EQ adjustments made using the
Manual MCACC setup do not appear
to change the reverb characteristics
graph after EQ calibration.
Despite level adjustments being made, the filters used for analysis may not display these
adjustments in the reverb characteristics graph after EQ calibration. However, these
adjustments are taken into account by the filters dedicated to overall system calibration.
Lower frequency response curves do
not seem to have been calibrated for
SMALL speakers.
Low frequencies used in bass management (the subwoofer channel) will not change for
speakers that have been specified as SMALL in the configuration, or do not output these
frequencies.
Calibration is performed, but due to your speakers’ low frequency limitations, no measur-
able sound is output for display.
Display
Symptom Remedy
The display is dark or off. Press DIMMER repeatedly to select a different brightness.
The OSD screen is not displayed. The on-screen display is not displayed unless this receiver’s HDMI OUT 1 or HDMI OUT
2 terminal is connected to the TV by HDMI cable. If the TV does not support HDMI, watch
this receiver’s front panel display when performing operations and making settings.
When the input is a 3D signal, OSD cannot be displayed.
Even through the input is switched,
DIGITAL does not light.
Check the digital connections and make sure that the digital inputs are assigned cor-
rectly (see The Input Setup menu on page 50 ).
DIGITAL or DTS does not light
when playing Dolby/DTS software.
These indicators do not light if playback is paused.
Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on
page 65 ).
Check the playback (especially the digital output) settings of the source component.
When playing Dolby Digital or DTS
sources, the receiver’s format indica-
tors do not light.
Check that the player is connected using a digital connection.
Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on
page 65 ).
Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to
PCM.
Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is
selected.
When playing certain discs, none of
the receiver’s format indicators light.
The disc may not contain multi-channel material. Check the disc packaging for more on
what audio tracks are recorded on the disc.
It does not light when the PCM signal or analog signal is input.
 
116

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer SC-LX58-S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer SC-LX58-S in de taal/talen: Engels als bijlage per email.

De handleiding is 16,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Pioneer SC-LX58-S

Pioneer SC-LX58-S Snelstart handleiding - Nederlands - 76 pagina's

Pioneer SC-LX58-S Gebruiksaanwijzing - Nederlands - 145 pagina's

Pioneer SC-LX58-S Snelstart handleiding - Deutsch - 76 pagina's

Pioneer SC-LX58-S Gebruiksaanwijzing - Deutsch - 147 pagina's

Pioneer SC-LX58-S Snelstart handleiding - English, Français - 76 pagina's

Pioneer SC-LX58-S Gebruiksaanwijzing - Français - 144 pagina's

Pioneer SC-LX58-S Snelstart handleiding - Italiano - 76 pagina's

Pioneer SC-LX58-S Gebruiksaanwijzing - Italiano - 143 pagina's

Pioneer SC-LX58-S Snelstart handleiding - Espanõl - 76 pagina's

Pioneer SC-LX58-S Gebruiksaanwijzing - Espanõl - 143 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info