811500

Pioneer ND-BC20PA Handleiding

2
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
En En En En
Basic Settings
Basic settings refer to those settings that are
mandatory. Basic settings are set during initial
setup. These settings can be changed later.
A. Centerline
Adjust the monitor connected to the rear view
camera. Adjust so that the vehicle centerline is
displayed in the center of the screen.
Note:
The centerline serves as a reference for vehicle
width when parked (orange line).
1. Press the ENTER button.
2. Adjust so that the centerline is in the
center of the screen using the + and
– buttons.
Adjust so that the number of lines is the
same on both sides of the screen.
Note:
Adjustment can be made within the range of –63
to +63.
3. Press the ENTER button.
When performing this procedure starting
from “First Time Setup”, proceed to
section B entitled “Position (Rotate)”.
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
B. Position (Rotate)
Adjust the rotation of the rear view camera
image as viewed from the location where the
rear view camera is installed.
1. Press the ENTER button.
2. Adjust the angle with the + and
– buttons.
•
•
Adjust the angle so that an object (such as
the tire blocks) serving as a reference along
the horizontal lines is displayed.
Horizontal lines
Note:
Adjustment can be made within the range of –511
to +511.
Some portions may not be able to be seen depend-
ing on the settings.
3. Press the ENTER button.
When performing this procedure starting
from “First Time Setup”, proceed to
section C entitled “Position (Horizontal)”.
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
C. Position (Horizontal)
Adjust the horizontal of the rear view camera
image as viewed from the location where the
rear view camera is installed.
1. Press the ENTER button.
2. Adjust the horizontal position with
the + and – buttons.
Adjust so that the center of the parking
space is displayed in the center of the
camera screen in the horizontal direction.
Horizontal direction centerline
Note:
Adjustment can be made within the range of –63
to +63.
•
•
•
3. Press the ENTER button.
When performing this procedure starting
from “First Time Setup”, proceed to
section D entitled “View Diagonal”.
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
D. View Diagonal
Adjust the inclination of the rear view camera
image as viewed from the location where the
rear view camera is installed.
1. Press the ENTER button.
2. Adjust view diagonal with the + and
– buttons.
Adjust view diagonal so that the white
lines of the parking space are displayed
symmetrically.
Centerline
Note:
Adjustment can be made within the range of –255
to +255.
3. Press the ENTER button.
When performing this procedure starting
from “First Time Setup”, proceed to
section E entitled “View Angle”.
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
•
E. View Angle
Adjust the view angle (high angle mode) as
viewed from directly overhead.
1. Press the ENTER button.
2. Adjust the angle with the + and
– buttons.
Adjust the angle so that the white lines are
aligned with the vertical lines.
Vertical lines
Note:
Adjustment can be made within the range of –511
to +511.
3. Press the ENTER button.
When performing this procedure starting
from “First Time Setup”, proceed to section
F entitled “Vertical Guideline (Width)”.
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
•
F. Vertical Guideline (Width)
Adjust the width within the vertical guidelines.
1. Press the ENTER button.
2. Adjust the position with the + and
– buttons.
Adjust the position using the white lines of
the parking space as a reference.
Vertical guidelines
Note:
Adjustment can be made within the range of –255
to +255.
3. Press the ENTER button.
4. Press the ENTER button twice.
When performing this procedure starting
from “First Time Setup”, proceed to step 6
of “First Time Setup”.
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
•
Changing Basic Settings or
Other Settings
Basic settings set during initial setup can be
changed. In addition, other settings can also
be made such as View (Wide/Zoom) and
Guideline (Shape) on “Advanced Settings”.
Begin the setup procedure after parking the
vehicle at the location where photographs
are to be taken by referring to the section on
“Preparations Before Beginning Setup”.
1. Put the vehicle in reverse.
Note:
When performing setup, always make sure to set
the parking brake and step on the brake to make
sure the car is stopped.
2. Simultaneously press the ENTER
and + buttons.
3. Press the ENTER button four times.
4. Take the photograph.
Take the photograph to be used for setup.
Take the photograph while referring to the
section on “Taking Photographs”.
5. Select the parameter to be set with
the + and – buttons and then press
the ENTER button.
Basic Settings
Set the basic settings
while referring to
“Basic Settings”.
6. Select OK and press the ENTER
button.
The settings are stored in memory.
Note:
Please make sure to read the caution and then
press the ENTER button to go to the next step.
Photograph data is deleted when setup is ended.
This camera and associated electronic guides are
intended solely as a driving aid. This unit is not
a substitute for you attentiveness, judgement, and
care while driving, moving, or parking your vehi-
cle. Always observe safe driving rules and driving
laws, even if they contradict the unit instructions.
•
•
•
•
Advanced Settings
Advanced settings such as View (Wide/Zoom)
and Guideline (Shape) can be set using
advanced settings.
A. View (Wide/Zoom)
This adjustment is only necessary when only
ground is displayed or when the display is too
small or illegible when viewed with the high
angle mode because of the height of the rear
view camera.
1. Press the ENTER button.
2. Adjust the view elevation with the +
and – buttons.
Note:
Adjustment can be made within the range of –63
to +63.
3. Press the ENTER button.
Return to step 5 of “Changing Basic
Settings or Other Settings”.
B. Guideline (Shape)
Adjust the inclination of the vehicle vertical
guidelines (shape) when there is a considerable
discrepancy with the vehicle width towards the
back of the field of view.
1. Press the ENTER button.
2. Adjust the angle with the + and
– buttons.
Vertical guidelines
Note:
Adjustment can be made within the range of –127
to +127.
3. Press the ENTER button.
4. Press the ENTER button twice.
Return to step 5 of “Changing Basic
Settings or Other Settings”.
Note:
The vertical guidelines (shape) setting reflect the
screen display of view angle and vertical guideline
(width).
•
•
•
C. Guideline (Distance)
The distance between the horizontal guidelines
can be adjusted. The horizontal guidelines are
displayed at the interval shown in Fig. 2 during
the initial setup when the camera has been
installed at the position shown in Fig. 1.
Fig. 1
1.5 m / 5 ft.
50˚
Approx.
1 m / 3 ft.
Approx.
1 m / 3 ft.
Fig. 2
Approx.
2 m / 7 ft.
Note:
The horizontal guidelines consist of three refer-
ence lines that serve as a reference when parking
(green, yellow and red lines).
In the case the “view angle” of the basic settings
has been adjusted from the factory adjustment,
the distances between the horizontal guidelines as
shown in Fig. 2 (approx. 1 m, 1 m and 2 m) will
be different.
1. Press the ENTER button.
2. Adjust the angle with the + and
– buttons.
Horizontal guidelines
Note:
Adjustment can be made within the range of –255
to +255.
3. Press the ENTER button.
4. Press the ENTER button twice.
Return to step 5 of “Changing Basic
Settings or Other Settings”.
•
•
•
Advanced Settings
Set the advanced settings
while referring to
“Advanced Settings”.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer ND-BC20PA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer ND-BC20PA in de taal/talen: Engels, Spaans als bijlage per email.

De handleiding is 1.29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Pioneer ND-BC20PA

Pioneer ND-BC20PA Installatiehandleiding - Deutsch, English, Français, Italiano, Espanõl - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info