13
3 When the lid (4) is open you can take the water
container (3) by the handle, tip it backwards slightly
and pull it out. Inserting has to be done in reverse
order.
7 For removing the pod holder (7) slide the swivel
lever (5) to the right hand-side into the starting posi-
tion 6 .
The coffee outlet (8) can be screwed in or out to
adjust the height.You can use the two outlet nozzles
and adjust the height or you can remove it out com-
pletely.
Turn the coffee outlet (8) upside down and the filter
insert will fall out. It provides an optimal crema quali-
ty. After cleaning it has to be inserted again as
demonstrated in picture 8 .
For the assembly of the coffee outlet (8) set it at the
thread as demonstrated in picture 9 and screw it in
up to the desired height. The two outlet nozzles
always have to be over the two openings of the drip
tray (9).
Anti-chlorine filter ACF 30 option
You can obtain the anti-chlorine filter ACF 30 (with 3 fil-
ter cartridges) wherever you purchased the appliance,
or you can order it directly from petra-electric.
5 The anti-chlorine filter (15) ensures a pure coffee
taste. It filters chlorine and other impurities out of the
water.
4 Put the filter cartridge (16) after rinsing it under
fresh water into the ring (17) from the top part. After-
wards, place the filter holder (18) and engage it by
turning.
5 In order to lock the already installed filter (15) in
the outlet of the water container (3), push it down-
wards as far as it will go.
The effect of the filter depends on how much the
coffeemaker is used. In case of a daily average con-
sumption of 8 cups of coffee, it should be exchanged
after 3 months (approx. 700 cups) at the latest.
4 Adjust the time of the next filter exchange on the
change indicator (19).
Ventilating (only new appliance)
Before you use the appliance for the first time,
the heating system has to be ventilated first.
1. Fill the water container (3) with fresh water up to
the max indication, insert it into the appliance and
close the lid (4).
Only fill the water container (3) with fresh water,
never with carbonated water or other liquids, e.g.
milk, etc.
2.Put a collecting bowl with a maximum height of 10
cm and a capacity of at least 650 ml or 2 big coffee
cups under the coffee outlet (8).
3. 7 Push the empty pod holder (7) into the brewing
chamber (6) and 10 push the swivel lever (5) over
the symbol .
Advice: If there is no pod holder (7) in the brewing
chamber (6), it is not possible to place the swivel
lever in the area of symbol “Brewing” .
4. 11 Push the ON/OFF button (12). The display
(10) illuminates red and after a few seconds the
pump starts to work. When the heating system is
filled, some water runs off into the collecting bowl
and the appliance switches off after approx. 60 se-
conds.
5. 11 Empty the collecting bowl and push the
ON/OFF button (12) once more. After approx.
60 seconds the pump switches off automatically
and the water in the appliance is heated-up until
the display changes to green.
Important advice: For a successful first usage it is
compulsory that both rinsing operations (4. and 5.)
work completely up to the automatic switch-off of the
pump (approx. 60 seconds). In case you switched off
the appliance manually beforehand, e.g. if a collec-
ting bowl was too small and thus overflowed, you
have to start the operation all over again by pushing
the ON/OFF button .
6.Before brewing coffee for the first time, you should
rinse the appliance once again as described in the
following section. Afterwards you can be sure that
any residue which might detract from your coffee
pleasure is eliminated.
Attention! The water is now hot!
Rinsing
If the appliance was not in use for several days you
should start rinsing in order to renew the water in the
heating system:
1.Put a collecting bowl with a maximum height of 10
cm and a capacity of at least 650 ml or 2 big coffee
cups under the coffee outlet (8).
2. 7 Push the empty pod holder (7) into the brewing
chamber (6) and 10 place the swivel lever (5)
over the symbol „Brewing“ .
3. 12 Push both start buttons (11) and
(13) briefly at the same time.The pump starts to
work and the display (10) illuminates red.
