- 27 -
0+ “Primo Viaggio SIP”, “Primo Viaggio Tri-fix”, “Primo
Viaggio Tri-fix e” and “Primo Viaggio Tri-fix es” car seats
can be attached to the Skate chassis.
Britax and Maxi-Cosi car seats can also be attached to
the Skate chassis with the Peg Perego adaptors.
32• Before fitting the adaptors, check that the attachments
on the Skate chassis are both in the central and vertical
position (Fig. a).
You can distinguish the right adaptor (DX) from the left
one (SX) by the letters DX and SX on the inner side.
To attach the Car Seat adaptors, place them into their
slots on the Skate chassis, lining up the notches on the
adaptors with those on the Skate chassis (Fig. b), and
click them into place (Fig. c).
33• To attach the car seat to the Skate chassis, position
the seat above the adaptors and facing the person
pushing, then push downwards.
WARNING: Line the car seat up with the chassis as
shown in the figure and check that it is properly
attached by ensuring that the red mark on the
adapter is no longer visible.
To release the car seat from the Skate chassis, use the
lever on the backrest of the car seat and lift it.
To release the adaptors, press the inner button and
pull them upwards.
REMOVABLE COVERS
How to remove the covers of the SKATE
BASSINET UNIT
Remove the hood, cover and front bar if they are
attached, and completely lower the backrest.
34• Remove the internal mattress pad by slipping it off the
backrest (Fig. a). Lift all of the inner padding (Fig. b)
and slide off the backrest adjuster strap (Fig.c).
35• First release the side tabs and then the one at the feet
end by pressing on the clip at the bottom and pushing
from outside (Fig. a).
Lift the side tabs (Fig. b) to aid the procedure. Next lift
the backrest to release the tab at the head end (Fig. c).
36• Lower the entire structure and the padding of the
Skate bassinet unit (Fig.a).
Remove the casing sections on both sides, lifting them
outwards from the inside (Fig.b).
37• Slip off the fabric covering in the order shown in the
figure, starting from the side of the backrest (first from
one corner, then from the other) to aid the procedure
(Fig.c).
Finally, slip the fabric covering off the feet on the
bottom of the Skate seat (Fig.d).
How to replace the covers of the SKATE
BASSINET UNIT
PLEASE NOTE: The head end of the Skate fabric
covering can be identified by the slot in the material
for the backrest adjuster strap.
38• Fit the padding, attaching it to the feet on the bottom
of the Skate bassinet unit, then the side of the feet (one
corner at a time) and next the side fasteners, making
quite sure that they remain on the outside (Fig.a).
Fit the fabric covering on the upper part (backrest side)
one corner at a time.
Lift the backrest and thread the backrest adjuster strap
from the inside to the outside of the Skate bassinet
unit (Fig.b).
Follow the instructions in points 9, 10 and 11.
Put the two casing sections in place (Fig.c).
How to remove the covers of the SKATE SEAT
Remove the hood, cover and front bar if they are
attached.
39• Open the two Velcro fastenings placed under the
footrest and pull out the straps (Fig. a).
Unfasten the side buttons (Fig. b).
Slide the fabric covering out from inside the casing
sections (Fig. c).
Unfasten the buttons on the side of the chassis (Fig. d).
40• Pull the leg divider strap of the harness out from under
the seat.
Release the belt behind the backrest and then pull out
the safety harness straps from the front (Fig. a).
Use a crosshead screwdriver to unscrew the strap from
the Skate seat on one side only, keeping a finger under
the nut (Fig. b).
41• Remove the fabric covering from the backrest
adjustment lever and pull the fabric covering off
upwards near the backrest.
Uncovered frame.
How to replace the covers of the SKATE SEAT
42• Fit the fabric covering onto the frame from the upper
part of the backrest (Fig. a), keeping the handle on the
outside.
• Thread the lower leg divider strap through under the
seat, leaving the higher leg divider strap above the
fabric covering (Fig. b).
• Insert the waist strap into the hole on the Skate
seat (Fig. c) and secure the strap with a crosshead
screwdriver (Fig. d).
43• Put the safety harness at the required height (Fig. a)
by threading the straps through the slots in the fabric
covering.
PLEASE NOTE: Place the buckles underneath the
support straps behind the backrest (Fig. b).
44• Fit the fabric covering onto the casing sections, first
on the upper part and then on the lower part, slightly
lifting the casing sections to attach it properly (Fig. a).
• Fasten the fabric covering’s two buttons to the frame,
ensuring that the Skate’s side attachments remain on
the outside (Fig.b).
Fasten the straps and stick the Velcro fastenings to the
footrest (Fig. c).
SERIAL NUMBERS
45• The following information can be found on the Skate
chassis (Fig. a), Skate bassinet unit (Fig. b) and Skate
seat (Fig. c): product name, production date and serial
number.
This information is required in the event of a complaint.
ACCESSORIES LINE
46• Skate Parasol: Practical matching parasol.
CLEANING AND MAINTENANCE
• This item requires a small amount of cleaning. Cleaning
and maintenance must only be carried out by adults.
• Keep all moving parts clean and if necessary lubricate
them with light oil, in line with the instructions given
in point 47.
• Dry the metal parts of the product to prevent rust.
• Clean the plastic parts periodically with a damp cloth.
Do not use solvents or similar substances.
• Protect this item from the elements: water, rain and
snow. Continual, extended exposure to the sun may
cause colour changes in many materials.
• Store this item in a dry place.
47• A - Keep clean and free of dust and stones.
B - Keep clean and free of dust and stones. Periodically
