706372
99
Verklein
Vergroot
Pagina terug
1/106
Pagina verder
94
GB / IE / NI
Checking:
(see figure 9)
- Adjust an angle gauge to 90° and
position it between the stop rail (17) and
the saw blade (6) on the turntable (15).
The leg of the angle gauge must be flush
with the saw blade (6) over the complete
length.
Adjusting:
(see figure 8/9)
- Loosen all four set screws (33) and turn
the stop rail (17) until the leg of the angle
gauge is flush with the stop rail over the
complete length.
- Retighten the four set screws again.
When the mitre angle pointer (12) is not
in line with the 0° mark of mitre angle
scale (14) after adjusting, loosen the
screw on the mitre angle pointer (12)
with a philips screwdriver and align the
angle pointer pointed to the 0°mark.
8.5 Cross cut 90° and turntable 0°
(Fig. 10/12)
In the case of cutting widths up to approx.
100 mm it is possible to fix the traction
function of the saw with the locking screw
(25) in the rear position. In this position the
machine can be operated in cross cutting
mode. If the cutting width is over 100 mm
then it is necessary to ensure that the locking
screw (25) is loose and the machine head (4)
can move.
•Movethemachinehead(4)toitsupper
position.
•Usethehandle(1)topushbackthe
machine head (4) and fix it in this
position if required(dependent on the
cutting width).
•Placethepieceofwoodtobecutatthe
stop rail (17) and on the turntable (15).
•Lockthematerialwiththeclamping
device (7) on the fixed saw table(16) to
prevent the material from moving during
the cutting operation.
•Operatethereleaselever(3)torelease
the machine head (4).
•PresstheON/OFFswitch(2)tostartthe
motor.
• Withthedragguide(26)fixedinplace:
• Usethehandle(1)tomovethemachine
head (4) steadily and with light pressure
downwards until the saw blade (6) has
completely cut through the work piece.
• Withthedragguide(26)notfixedin
place:
• Pullthemachinehead(4)alltheway
to the front. Lower the handle (1) to the
very bottom by applying steady and
light downward pressure. Now push the
machine head (4) slowly and steadily to
the very back until the saw blade (6) has
completely cut through the work piece.
• Whenthecuttingoperationiscompleted,
move the machine head (4) back to its
upper (home) position and release the
ON/OFF switch (2).
Attention! The machine executes an upward
stroke automatically due to the return
spring, i.e. do not release the handle (1)
after completing the cut; instead allow the
machine head to move upwards slowly
whilst applying light counter pressure.
8.6 Cross cut 90° and metre cut 0°
- 45° (Fig. 10/11)
The crosscut saw can be used to make
crosscuts of 0° -45° to the left and 0° - 45° to
the right in relation to the stop rail.
•Loosenthemetrelockhandle(10)incase
it is tightened, press the metre detent
lever (11) and use the mitre lock handle
(10) to adjust the turntable (15) to the
desired angle. The mitre angle pointer
(12) on the turntable must match the
desired angle on the mitre angle scale
(14) on the fixed saw table (16).
•Re-tightenthemitrelockhandle(10)in
order to secure the turntable (15).
Attachment and operation
99

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Parkside-PZKS-1500-B2---IAN-280657

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PZKS 1500 B2 - IAN 280657 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PZKS 1500 B2 - IAN 280657 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 2,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info