763020
19
Verklein
Vergroot
Pagina terug
1/49
Pagina verder
19GB/IE/NI
Distance cutting
In some case, it is beneficial cut while
holding the burner sleeve 8c at a height of
1.5 mm to 3 mm above the workpiece. This
reduces the quantity of material that is blown
back into the tip. This makes it possible to
penetrate thicker material strengths. Distance
cutting should be used if penetration or
furrow work is carried out. Furthermore, the
“distance” working technique can be used
when you need to cut sheet metal to
minimise the risk of material splashing back
which could damage the tip.
Perforation
To drill through place the tip approx.
3.2 mm above the workpiece. Hold the
plasma burner at a slight 8 angle to guide
the sparks away from the burner sleeve 8c
and your body. Press the plasma burner
button 8a and lower the tip of the plasma
burner until there is a main cutting arch and
sparks begin to form. Test the perforation on
a test object that is no longer needed and
once there are no problems start drilling
through at the previously defined cutting line
on your workpiece. Check the plasma
burner 8 for wear and tear, cracks or
exposed cable pieces. Replace or repair
them prior to using the device. A badly worn
burner sleeve 8c contributes to the reduction
of speed, voltage and unclean separation.
An indication of a badly worn burner sleeve
8c is an extended or oversized nozzle
opening. The external electrode 8d must not
be recessed by more than 3.2 mm. Replace
it if it is more worn than the specified
dimension. If the protective cap is difficult to
tighten, check the thread.
Using the device / Troubleshooting
Faults Cause of fault Troubleshooting
Indicator lamp
does not lit up? No electrical connection.
ON/OFF switch set to off. Check whether the device is
connected to the socket.
Set switch to ON.
Ventilator does
not work? Power line interrupted.
Power line ventilator faulty.
Ventilator faulty.
Check whether the device is
connected to the socket.
Warning lamp
switches on? Overheating protection
switched on.
Input voltage too high.
Allow device to cool down.
Input voltage according to
type plate.
No output
current? Machine faulty.
Overvoltage protection
activated.
Machine must be repaired.
Allow device to cool down.
Output current
does not
decrease?
Input voltage too low.
Connection cable cross-section
too low.
Observe input voltage
according to type plate.
• Troubleshooting
327358_Plasmaschneider_PPS_40_B2_content_LB6_IE_NI.indb 19 06.09.2019 12:41:03
19

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Parkside-PPS-40-B2---IAN-327358

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PPS 40 B2 - IAN 327358 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PPS 40 B2 - IAN 327358 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info