763020
18
Verklein
Vergroot
Pagina terug
1/49
Pagina verder
18 GB/IE/NI
• Using the device
• Operation
1. Set the plasma cutter 1 up in a dry and
well ventilated area.
2. Position the machine in the vicinity of the
workpiece.
3. Press the on/off switch 17.
4. Clamp the ground terminal 4 to the
workpiece to be cut and make sure that
there is a good electrical contact.
5. Set the cutting current on the current
controller 13. If the arc beam is inter-
rupted the cutting current must be set
higher if necessary. If the electrode burns
through frequently, then the cutting
current must be set lower.
6. Position the plasma cutter 8 on the
workpiece so that the burner sleeve 8c is
free and that a blowback of the molten
metal is not possible. Press the plasma
burner button 8a. The transmitted cutting
arch is ignited on the edge of the sheet
in this manner.
7. Start cutting slowly and then increase the
speed in order to achieve the desired
cutting quality.
8. The speed must be regulated so that a
good cutting capacity can be achieved.
The plasma beam creates a straight arch
(stainless steel, aluminium) or a 5° arch
of approach (soft steel).
To cut in the manual cutting mode,
pull the overlying burner across the
workpiece while maintaining a
constant speed. To achieve the perfect cut, it
is important for the material thickness to
comply with the correct cutting speed. If the
cutting speed is too low, the cutting edge will
be blunt due to the severe heat input.
The optimal cutting speed is achieved once
the cutting jet is slightly inclined towards the
rear while cutting. If the plasma burner
button 8a is released, the plasma jet goes
out and the power source switches off. The
gas continues to flow for approx. 5 seconds
in order to cool the burner. The same
process is followed when the workpiece is
pulled out with a pressed plasma burner
button 8a. During the gas post-flow time,
the plasma cutter 1 must not be switched off
to avoid damaging the plasma burner 8 as
a result of overheating.
ATTENTION!
fThe device must be left on for approx.
2-3 minutes once the cutting work has
been completed. The cooler cools the
electronics.
• Types of plasma cutting
Drag cutting
Hold the tip of the burner sleeve
8c
low over
the workpiece and press the plasma burner
button
8a
. Now move the burner sleeve until
8c
there is contact with the workpiece and
the cutting arch is fixed. Once the cutting
arch has been generated, move the plasma
burner
8
in the desired direction. Makes
sure that burner sleeve is slightly
8c
angled
and that contact with the workpiece is
maintained. This working method is called
drag cutting. Avoid quick movements. A sign
of quick movements is sparks that fall of the
top of the workpiece. Move the plasma
burner at a
8
speed in which the spark
accumulation is concentrated on the bottom
side of the workpiece. Ensure the material is
completely separated prior to continuing with
this process. Set the necessary drag speed.
Using the device
327358_Plasmaschneider_PPS_40_B2_content_LB6_IE_NI.indb 18 06.09.2019 12:41:02
18

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Parkside-PPS-40-B2---IAN-327358

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PPS 40 B2 - IAN 327358 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PPS 40 B2 - IAN 327358 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info