748074
29
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
29
IEGB
1. Press the spindle locking button
(16) on the front side of the ma-
chine and keep it pressed down.
2. Use the combination wrench (27)
to loosen the cap nut (8) as much
as needed, so that the cutter can
be inserted.
3. Release the spindle locking but-
ton (16).
4. Insert the desired cutter into the
already mounted collet chuck
(13). The cutter shaft must be
pushed in at least 20 mm.
5. Use the combination wrench (27)
to tighten the cap nut (8) while
keeping the spindle locking but-
ton (16) pressed.
Tighten the cap nut only when a
cutter is inserted. The collet chuck
might get damaged.
Change collet chuck
All cutters of the 6-part cutter set included
in the delivery are provided with an 8-mm
cutter shaft.
Change the collet chuck for cutters with a
6-mm cutter shaft.
1. Press the spindle locking button (16) on
the front side of the machine and keep
it pressed down.
2. Screw off the cap nut (8) using the com-
bination wrench (
27).
3. Release the spindle locking button (16).
4. Take out the 8mm collet chuck (13) and
insert the 6mm collet chuck (22) and
the spring (37) included in the delivery
in the sequence shown in the diagram.
5. Screw the cap nut (8) loosely back on.
6. Insert a cutter as described above .
Tighten the cap nut only when a
cutter is inserted. The collet chuck
might get damaged.
Connecting the suction
adapter
You can reduce dust formation while you
work by connecting a dust suction system.
1. Fit the suction adapter (20) on the pro-
vided drill holes (
12) in the base-
plate (10).
2. Screw on the 2 recessed head screws
(21) from the bottom side of the base-
plate (10).
3. Fit the reducer part (30) on the suction
adapter if needed.
4. Connect the suction hose of a vacuum
cleaner to the suction adaptor (20).
The vacuum cleaner must be
suitable for the workpiece to be
processed. Use a special vacuum
cleaner if dusts with hazard for
health are created.
Mounting the parallel stop
1. Screw both screws out of the guide
bars (29).
2. Screw the guide bars (29) onto the par-
allel stop (24) using the spanner (27).
Adjust cutting depth
The switch has 6 levels:
0 - 5 - 10 - 15 - 20 - 25 mm
Before you begin to set the milling
depth, turn the rotary knob (2) until
the ne adjustment pin is unscre-
wed from the depth stop (17) by
approx. 5 mm.
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 304379 POF 1200 C2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 304379 POF 1200 C2 in de taal/talen: Nederlands, Duits, Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 3,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info