748151
25
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
18 GB/IE
(2). If this is not the case, the angle of the top saw band
roller (2) must be corrected.
If the Bandsaw blade (21) runs more towards the rear
edge of the saw band roller (2) then the set screw (14)
must be rotated anticlockwise.
Open the locking screw for the top saw band roller (13).
Turn the bottom saw band roller (8) slowly by hand, to
check the position of the Bandsaw blade (21).
If the Bandsaw blade (21) runs more towards the front
edge of the saw band roller (2) then the set screw (14)
must be rotated clockwise.
After setting the top saw band roller (2), check the position
of the Bandsaw blade (21) on the bottom saw band roller
(8). The Bandsaw blade (21) should also lie centrally on
the saw band roller (8) here. If this is not the case, the an-
gle of the top saw band roller (2) must be adjusted again.
Turn the saw band roller a few times, until the adjustment
of the top saw band roller (2) acts on the saw band posi-
tion on the bottom saw band roller (8).
Tighten the locking screw for the top saw band roller (13).
Once adjustment is complete, close the side covers (11)
again and secure with the cover locking mechanisms (10)
with the help of the screwdriver (29).
8.4 Adjusting the saw band guide (Fig. 5 - 8)
Both the support bearing (36 + 42) and the guide pins (37 +
46) must be readjusted after every saw band change.
Open the side covers (11) by undoing the cover locking
mechanisms (10) with the help of the screwdriver (29).
8.4.1 Top support bearing (36) ( Fig. 5)
Undo Allen screw for top support bearing (35).
Move support bearing (36) sufficiently far that it just no
longer touches the Bandsaw blade (21) (distance max.
0.5 mm).
Retighten the Allen screw for the top support bearing (35).
8.4.2 Adjusting the bottom support bearing (42)
(Fig. 7)
Disassemble the saw table as per 9.1 in the opposite di-
rection.
Undo Allen screw for bottom support bearing (41).
Move bottom support bearing (42) sufciently far that it
just no longer touches the Bandsaw blade (21) (distance
max. 0.5 mm).
Retighten Allen screw for bottom support bearing (41).
8.4.3 Adjusting the top guide pins (37)
Undo Allen screws for top retainer (40)
Move top retainer (39), top guide pins (37), until the front
edge of the guide pins (37) is approx. 1 mm behind the
tooth base of the saw band.
Retighten Allen screws for top retainer (40).
ATTENTION! The saw band will be unusable if the teeth
touch the guide pins with the saw band running.
Undo Allen screws for top guide pins (38).
Slide the guide pins (37) in the direction of the saw band!
Attention! The distance between the guide pins (37) and
Bandsaw blade (21) must not exceed 0.5 mm. (Saw band
must not jam)
Retighten Allen screws (38).
Before you actuate the On/Off switch, make sure that the
saw blade is correctly fitted and that the machines moving
parts run smoothly.
Before you connect the machine to the power supply,
make sure the data on the rating plate is the same as that
for your mains.
8. Attachment
ATTENTION!
Before all maintenance, set-up and assembly work on the
band saw, unplug the mains plug.
Assembly tools
1 Open-ended spanner, size 10/13
1 Allen key, size 3
1 Allen key, size 4
1 Screwdriver
The saw table is not assembled for packaging reasons.
8.1 Assembling the saw table (Fig. 2-4)
Remove the wing nut (31), the locking handle (20), the two
washers and the clamping plate (32). (Fig. 2)
Remove the two knurled nuts (33), the U-reinforcement
(34) and the two countersunk screws M6x16 from the saw
table. (Fig. 3)
Guide the saw table (7) over the Bandsaw blade (21).
Fasten it to the two screws on the machine frame with the
plate (32), the two washers, the wing nut (31) and the
locking handle (20). (Fig. 4)
Fasten the U-reinforcement (34) to the front side of the saw
table with 2 countersunk screws M6x16 and 2 knurled
nuts (33). (Fig.3)
8.2 Tensioning the saw band (Fig. 1a)
ATTENTION! If the saw is at a standstill for an extended
period the saw band tension must be relieved, i.e. before
switching the saw on it is necessary to check the saw
blade tension.
Turn the clamping screw (1) clockwise to tension the Band-
saw blade (21). The correct tension of the saw band can
be determined by pressing the finger laterally against the
saw band, roughly centrally between the two saw band
rollers (2+8). The Bandsaw blade (21) should only de-
press slightly (approx. 1-2 mm) here.
The sufficiently tensioned saw band makes a metallic
sound when tapped.
Relieve the saw band tension if it is not in use for an ex-
tended time, so that it does not become overstretched.
ATTENTION! With high tension, the saw band may break.
RISK OF INJURY! If the tension is too low, the driven saw
band roller (8) may spin, resulting in the saw band coming
to a standstill.
8.3 Adjusting the saw band (Fig. 1a+1b)
ATTENTION! Before it is possible to implement the saw
band setting, the saw band must be tensioned correctly.
Open the side covers (11) by undoing the cover locking
mechanisms (10) with the help of the screwdriver (29).
Slowly turn the saw band roller (2) clockwise. The Band-
saw blade (21) should run centrally on the saw band roller
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 303408 PBS 350 A1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 303408 PBS 350 A1 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 3,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info