745935
15
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
15
NIIEGB
The template must be at least as
high as the ball race (26) of the
template guide (25).
Milling with centring tip
By means of the centring tip, you can do
circular milling work.
1. Turn the parallel stop (24) around
so that the stop edge points up.
2. Screw on the centring tip (23)
on the parallel stop by means of
the buttery nut. In the process,
counter lock the centring tip in
the long hole of the combination
wrench
(
27).
3. Screw the guide bars (29) of the
parallel stop (24) on the base-
plate (10) and tighten the retain-
ing screws (9).
4. Push the centring tip (23) in the
marked centre of the circle to be
cut.
5. Move the machine circularly once
in the circle around the centring
tip (23).
Cleaning/maintenance
Ask our service centre to carry out
any work that is not described in
these instructions. Use only original
parts. In this way you avoid dam-
age to the appliance and possible
injury to people.
Pull out the power plug before car-
rying out any work on the equip-
ment. There is a risk of electrocution
or of injury from moving parts.
1. Insert the parallel stop (24) with
the guide bars (29) into the guide
rails (15) of the baseplate (10).
Tighten the retaining screws (9).
2. Move the turned on machine
along the workpiece edge with
lateral pressure on the parallel
stop (24).
Milling with template guide
By means of the template guide (25), you
can transfer contours from templates to
workpieces.
Inserting the template
guide:
1. Screw off the suction adapter as
applies.
2. Insert the template guide (25) into
the sliding plate (11). The ball
race (26) must point down.
3. Fasten the template guide (25)
to the recessed head screws (21)
that are included in the delivery.
Inserting the cutter:
4. Insert a cutter that has a diameter
smaller than the inner diameter of
the template guide (25).
5. Set the desired cutting depth (see
“Initial operation”).
Milling with template guide
6. Loosen the clamping lever
(
19) and lower the machine
downward until the previously set
cutting depth is reached.
7. Move the machine with protrud-
ing template guide (25) along the
template. Apply slight pressure
during this work.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 275390 POF 1200 B2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 275390 POF 1200 B2 in de taal/talen: Nederlands, Duits, Engels, Deens als bijlage per email.

De handleiding is 4,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Parkside IAN 275390 POF 1200 B2

Parkside IAN 275390 POF 1200 B2 Gebruiksaanwijzing - Français, Italiano - 84 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info