745342
10
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
7
PFS 710 C2
GB
IE
Switch the appliance on and only then move it
towards the material to be worked.
Switch the appliance off immediately if the saw
blade jams.
Open up the sawn gap using a suitable tool
and pull out the sabre saw.
Adapt the saw blade and stroke rate to the
material to be worked.
Optimised saw blades in different lengths
are available from a retail store to suit every
intended purpose.
Saw the material at a constant speed.
Sawing flush:
The flexible saw blades and suitable corresponding
length, enable you to saw off protruding workpieces
such as pipes which are close to the wall.
For this, proceed as follows:
1. Place the saw blade directly against the wall.
2. Bend it by applying lateral pressure to the sabre
saw so that the footplate
makes contact with
the wall.
3. Switch the appliance on as described and saw
off the work piece by applying constant pressure.
Plunge sawing:
CAUTION! RISK OF KICKBACK!
Plunge cuts may only be made in soft materi-
als (wood or similar).
Proceed as follows:
1. Place the sabre saw with the lower edge of the
footplate
onto the workpiece. Switch the
appliance on.
2. Tilt the sabre saw forwards and plunge the saw
blade into the workpiece.
3. Position the sabre saw vertically and continue
sawing along the cutting line.
NOTE
The saw blade to be used should not exceed
a max. length of 152 mm!
Maintenance and cleaning
WARNING! RISK OF INJURY! Always
switch the appliance off before
carrying out any work on it.
Always remove the power plug from the power
socket before cleaning the appliance.
Replace the saw blade as soon as its teeth are
blunt and proper sawing is therefore no longer
possible.
Keep the appliance and ventilation slits clean at
all times. If the ventilation slits are blocked, there
is the risk of overheating and / or the appliance
being damaged.
Always clean the appliance after completion
of work.
Never permit fluids to penetrate inside the appli-
ance. Use a cloth to clean the housing. Never
use petrol, solvents or cleansers which can
damage plastic.
Clean the saw blade mount, if necessary with a
brush or by blowing it out with compressed air.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 272950 PFS 710 C2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 272950 PFS 710 C2 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info