745332
13
Verklein
Vergroot
Pagina terug
1/122
Pagina verder
13
IEGB
Special safety instructions for
grinding and cutting
a) Use only grinders which have been
approved for your electric tool and the
protective hood intended for these grin-
ders. Grinders which are not intended
for the electric tool may not be sufci-
ently shielded and are unsafe.
b) Depressed Center grinding wheels must
be pre-assembled so that their surface
not above the level of the edge of the
guard stands out. An improperly moun-
ted grinding wheel, which extends bey-
ond the level of the edge of the guard,
not sufciently shielded.
c) The protective hood must be securely
attached to the electric tool and adjus-
ted so that the greatest level of safety
is reached, i.e., the smallest possible
amount of the grinder is exposed to the
operator. The protective hood should
protect the operator from broken bits
and accidental contact with the grinder.
d) Grinders may only be used for the
recommended attachment options. For
example: Never grind with the side
surface of a cutting disc. Cutting discs
are for cutting material using the edge
of the disc. Pushing sideways on these
grinders can break them.
e) Always use undamaged clamping an-
ges of the correct size and shape for
the grinding disc you selected. Suitable
anges support the grinding disc and
thus reduce the danger of the grinding
disc breaking. Flanges for cutting discs
can be distinguished from anges for
other grinding discs.
f) Do not use worn grinding discs for
larger electric tools. Grinding discs for
larger electric tools are not set up for
the higher rotation speeds of smaller
electric tools and can break.
Other special safety instructions
for cutting grinding
a) Avoid blocking the cutting disc or pres-
sing down too hard. Do not make any
excessively deep cuts. Overloading the
cutting disc increases wear and its ten-
dency to tilt or block and, with that, to
kickback or break the grinder.
b) Avoid the area in front of and behind
the rotating cutting disc. When you
move the cutting disc by itself in the
workpiece, in the event that the electric
tool kicks back with the rotating disc, it
can spin directly towards you.
c) If the cutting disc jams, or you interrupt
your work, switch the device off and
hold it until the disc has come to a full
stop. Never try to pull the cutting disc
out of the cut while it is still running,
because it can kick back. Identify and
correct the cause of the jamming.
d) Do not switch the electric tool on again
as long as it is in the workpiece. Allow
the cutting disc to rst reach its full
rotational speed before you carefully
resume with the cutting. Otherwise, the
disc may catch, spring away from the
workpiece or cause a kickback.
e) Support plates or workpieces to reduce
the risk of kickback from a jammed cut-
ting disc. Large workpieces may bend
under their own weight. The workpiece
must be supported on both sides of the
disc, near the cutting disc as well as
also at the edge.
f) Be particularly careful for pocket cuts in
existing walls or other areas where you
cannot see what is there. The cutting
disc may cause a kickback when it cuts
into gas or water lines, electrical lines
or other hidden objects.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 114254 PWS 125 B2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 114254 PWS 125 B2 in de taal/talen: Nederlands, Duits, Engels, Deens, Zweeds als bijlage per email.

De handleiding is 1,77 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info