511534
105
Verklein
Vergroot
Pagina terug
1/179
Pagina verder
[PROJECTOR SETUP] menu
ENGLISH - 105
Settings
z
Error details
Error message Remedy
[Exceed maximum
number of projectors.]
z
Set no more than eight
projectors in one group.
z
Use a computer and
the dedicated “Multi
Projector Monitoring &
Control Software”
*1
to
connect nine or more
projectors.
[Please check the
COMMAND CONTROL
setting.]
z
Set the on-screen menu
[NETWORK CONTROL]
[COMMAND CONTROL]
to [ON] for the projector
in error.
z
Set the [NETWORK
CONTROL] [COMMAND
PORT] of all projectors
to be connected to the
same value.
[Please check the
USER NAME and
PASSWORD in the
COMMAND CONTROL
setting.]
z
Set the same character
string to the [User
name] and [Password]
that has Web control
administrator rights
for all projectors to be
connected.
[Cannot apply
BRIGHTNESS
CONTROL. Please
check projector status.]
z
The projector is in
standby status. Switch
on the projector.
[Brightness Sensor
Error]
z
There is a problem with
the luminance sensor.
If the problem is not
corrected by turning off
the power and turning it
on again, consult your
dealer.
*1: “Multi Projector Monitoring & Control Software” is included
in the attached CD-ROM.
Note
z
Check the following when a projector to be
connected is not listed.

Is there a device on the network with the same IP
address?

Is a LAN cable connected correctly? (
page 126)

Is the projector subnet identical?

Is [LINK] set to the same group?
z
To change a projector name, refer to [NETWORK
SETUP] (
page 125), or [Network cong] page
(
page 133).
z
When [MODE] in [BRIGHTNESS
CONTROL SETUP] is [PC]
0(18
5(7851
02'(
352-(&725
3&
%5,*+71(66&21752/67$786
(1) Displays the name of the projector in question.
(2) Uses color to display status.
Green
:
There is margin for brightness correction.
Yellow
:
There is less margin for brightness correction.
Red: An error occurred in luminance control.
Example steps to adjust
luminance control
The steps exemplify an adjustment to link the
brightness of eight projectors connected in a network.
1) Use a LAN cable to connect all
projectors to a hub. (
page 126)
2) Switch on all projectors.
3) Set [LAMP SELECT] to either [DUAL]
or [SINGLE] for all projectors.
4) Set [MODE] in [BRIGHTNESS
CONTROL SETUP] to [OFF] and
[APPLY].
5) Set [SUBNET MASK] of the projectors
to the same value, and [IP ADDRESS]
of each projector to a different value
so that the network can communicate.
6) Wait at least eight minutes until the
lamp brightness becomes steady.
7) Set all items in the [PICTURE] menu of
all projectors to the same values.
8) To match colors, adjust [COLOR
MATCHING].
9) Display the internal test patterns of all
projectors in completely white”.
105

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic PT-DZ21KE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic PT-DZ21KE in de taal/talen: Engels als bijlage per email.

De handleiding is 17,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Panasonic PT-DZ21KE

Panasonic PT-DZ21KE Gebruiksaanwijzing - Deutsch - 190 pagina's

Panasonic PT-DZ21KE Gebruiksaanwijzing - Deutsch - 190 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info