569364
79
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
79
VQT4W64
Reference
Picture does not appear during timer recording.
¾ Timer recordings work regardless whether the unit is on or off.
To confirm the timer recording is going to work properly, turn the
unit on.
The screen changes automatically.
¾ When “Screen Saver” in the Setup menu is set to “On”, the
display may turn to the screen saver mode automatically if
there is no operation for 5 minutes or more. (> 68) Press [OK]
to return to the previous screen.
There is a lot of after-image when playing video.
¾ Set “Playback NR” in the Picture menu to “Off”. (> 60)
There is no apparent change in picture quality
when adjusted with the Picture menu in the on-
screen menus.
¾ The effect is less perceivable with some types of video.
The images from this unit do not appear on the
television.
Picture is distorted.
¾ Make sure that the television is connected to the AV1 terminal,
VIDEO OUT terminal or HDMI terminal on this unit.
(> 6, 7, 73, 74)
¾
Make sure that the television’s input setting (e.g., AV 1) is correct.
¾ The unit’s “TV System” setting differs from the TV system used
by the disc now playing. While stopped, keep pressing [] and
[< OPEN/CLOSE] on the main unit for 5 or more seconds. The
system switches from PAL to NTSC or vice versa. (> 69)
¾ When this unit is connected with an HDMI cable, use a disc that
matches with this unit’s TV system.
¾ Picture may not be seen when more than 4 devices are
connected with HDMI cables.
Reduce the number of connected devices.
The picture is distorted during play, or video will
not play correctly.
¾ You may be playing a TV programme recorded with poor
reception or unfavourable weather conditions.
¾ The picture may be distorted or a black screen may appear
briefly between recorded titles in the following situations:
between titles recorded with different recording modes.
between scenes recorded with different aspect ratios.
between scenes recorded with different resolutions.
between playlist chapters.
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio type.
¾ Check the connections and the “Digital Audio Output” settings.
Check the input mode on the amplifier if you have connected
one. (> 7, 68, 69, 73, 74)
¾ Press [AUDIO] to select the audio. (> 33)
¾ Audio may not be heard when more than 4 devices are
connected with HDMI cables.
Reduce the number of connected devices.
¾ The sound effects will not work when the bitstream signal is
output from the HDMI AV OUT terminal or the OPTICAL
DIGITAL AUDIO OUT terminal.
¾ To output audio from a device connected with an HDMI cable,
set “Digital Audio Output” to “HDMI and Optical” in the Setup
menu. (> 69)
¾ Depending on the connected equipment, the sound may be
distorted if this unit is connected with an HDMI cable.
¾ When “Rec for High Speed Copy” is set to “On”, you can only
record either the main or secondary audio of a bilingual
broadcast.
If you do not intend to copy the title to a DVD-R, DVD-R DL,
DVD-RW (DVD-Video format), +R, +R DL or +RW set “Rec for
High Speed Copy” in the Setup menu to “Off”. (> 67)
Cannot switch audio.
¾ You cannot switch the audio in the following cases.
When a DVD-R, DVD-R DL, DVD-RW (DVD-Video format),
+R, +R DL or +RW disc is in the disc tray while DVD drive is
selected.
When the recording mode is XP and “Audio Mode for XP
Recording” is set to “LPCM”. (> 68)
When “Rec for High Speed Copy” is set to “On”. (The default
setting is “On”). (> 67)
¾ The amplifier is connected using an optical digital cable or an
HDMI cable. You cannot switch the audio if “Dolby Digital” is set
to “Bitstream”. Set “Dolby Digital” to “PCM” or connect using
audio cables. (> 7, 68, 73)
¾ There are discs for which audio cannot be changed because of
how the disc was created.
Cannot operate the television.
The remote control doesn’t work.
¾ Change the manufacturer code. Some televisions cannot be
operated even if you change the code. (> 72)
¾ The remote control and main unit are using different codes.
Change the code on the remote control. (> 70)
Press and hold [OK] and the indicated
number button at the same time for
more than 5 seconds.
¾ The batteries are depleted. Replace them with new ones. (> 2)
¾ You are not pointing the remote control at the main unit’s
remote control signal sensor during operation. (> 2)
¾ Coloured glass may obstruct the signal reception/transmission.
¾ Don’t place the signal sensor in direct sunlight or in areas that
may be subject to sunlight exposure.
¾ It may be necessary to set the code on the remote control again
after changing the batteries. (> 70)
¾ It may be necessary to set the manufacturer code again after
changing the batteries. (> 72)
¾ The HOLD function is activated. (> 72)
The unit is on but cannot be operated.
¾ Playback drive has not been selected properly. (> 18)
¾ Some operations may be prohibited by the disc.
¾ The unit is hot (“U59” appears on the display). Wait for “U59” to
disappear.
¾ One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [Í/I] on
the main unit for about 3 seconds. The unit is forcibly
switched to standby.
Alternatively, disconnect the AC mains lead, wait one
minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If the unit still
cannot be operated, consult the dealer.
Cannot eject disc.
¾ The unit is recording.
¾
Linked timer recordings with external equipment is in recording
standby (“EXT-L” on the unit’s display blinks when [
Í
] is pressed).
Press [EXT LINK] to cancel the recording standby. (
>
25)
¾ The unit may have a problem. While the unit is off, press and
hold [] and [CH W] on the main unit at the same time for about
5 seconds. Remove the disc and consult the dealer.
If the HOLD function is activated, above operation does not
work. Cancel the HOLD function. (> 72)
Sound
Operation
DMREX96C-VQTXXXX_eng.book 79 ページ 2013年3月5日 火曜日 午後5時51分
79

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic DMREX96CEG bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic DMREX96CEG in de taal/talen: Engels als bijlage per email.

De handleiding is 4,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Panasonic DMREX96CEG

Panasonic DMREX96CEG Gebruiksaanwijzing - Deutsch - 88 pagina's

Panasonic DMREX96CEG Gebruiksaanwijzing - Français - 88 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info