649850
9
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
English
Warning:
Before using this projector, please read the manual carefully. Any wrong
operation may cause electric shock or fire. Please comply with the following
instructions when using and/or repairing the projector.
1. Clean
When clean this projector, please unplug the power cable and use the wet cloth
not the cleanser.
2. Accessories
Please use the recommended accessories or the projector maybe damaged.
3. Using environment
Do not place the projector on any wet environments.
4. Installation
Please place this projector on a stable surface
5. Ventilation
For best performance, please clean the filter once a month.
6. Power
Before plug in the power, please make sure the voltage of your area matches
this projector (220V or 110V).
7. Ground wire
The three pin plug is the ground wire of this projector.
8. Protect the power cable
Make sure the power cable is in perfect working condition before using it.
9.
Thunder
When there is thunder or not using
the projector for a long period of time , unplug the power cable.
10.
Repair
Due to high voltage, do not open or try to repair the projector by yourself.
Refer to a professional technician if repair is needed.
11. Heat
Make sure not to put this projector near any heating devices. That may
shorten the life span of the projector.
English
About the installation
In order to improve this projector's life span, do not place it on a wet surface.
Do not put the projector under the direct sun light.
Projector working temperature: 0°C - +50 °C
Projector store temperature : -20°C - +50 °C
Do not block the ventilation-window of the projector. If the projector
interior temperature is too hot, it will be automatically shut down. This will
protect the projector. To prevent over heating the projector, please clean
the filter once a month.
About turn on/off the projector
To turn on the projector, connect the power cable, then press the "power" key
on the panel. It will take couple of minutes before the lamp works normally.
To turn off the projector, press the "power" key again. The lamp will shut
off while the fan will still working for a little longer. The projector will shut off
automatic--ally when the fan stops. DO NOT unplug the power cable before
turn off the projector.
Warning:
The fan is to keep the projector's temperature low. It will turn on when projector
is turned on. The speed of the fan is according to the heat of the projector. Do
not unplug the power cable when the projector is not turned off and the fan
is still working. If the fan stops working, the projector may be damaged due to
overheat.
Troubleshooting
Problem
The possible causes
When turn on the
power, the indicator light
does not work
power cable did not connect well.
the power switch fuse is broken
The remote control
cannot turn on the
projector.
the power switch is turned off
the remote control has no batteries or
the batteries are low
the remote control does not aim at the
IR
point
No Image
the choice of the input source may not be
correct
no input signal
the input cable is not connected
if under PC mode, the PC output frequency is
not 50-60Hz. Make sure that the PC output is
connected with the projector.
Auto-off after use some
times
the projector ventilation is blocked
the voltage is not stable
the projector is overheated, check if the fan
is broken
English
Machine instruction
1.
Focus lens
2.
IR receiver
3.
Level-stand adjustment
4.
Cool winds input ventilation
5.
Input terminals
6.
Power switch
7.
Keystone
8.
Hot winds output ventilation
9.
Speaker
10.
Level-stand adjustment
11.
Projector mount hole
12.
Label
13.
Cool winds input ventilation
English
Interface
Name
Instruction
Y/ Pb / Pr
Component video input
Video
AV input
L-Out , R-Out
Audio output
L-In , R-In
Audio input
VGA IN
VGA input
TV
N/A
HDMI 1/2
HDMI
Signal input
USB
1/2
Connect USB flash drive
Caution
Please connect the input signal cable well , then turn on the projector
Otherwise, it is easy to damage the projector.
English
Installation method
Contact a professional installer to mount this projector to a ceiling. Follow the
instructions below for the correct projector positions:
Warning
1. This projector maybe damaged beyond repair if it is
incorrectly mounted on a ceiling or on a surface.
2. This projector can be only used in an environment with the
temperature that's not exceeding the range of 0-35°C. If the
temperature is outside the normal range, it may cause the
projector malfunction.
3. It may cause malfunction if the projector is placed in a dusty,
wet, moist or smoke environment.
4. Take care of the ventilation. Otherwise, the projector maybe
damaged or cause life threatening situation due to overheat.
English
Standard setting
Please refer to the following table to adjust your picture size and distance (from the
lens to screen )
Distance 4:3 16:9
50" 1.85m 2.00m
70" 2.55m 2.75m
100" 3.50m 3.85m
120" 4.18m 4.58m
Please allow +- 3% to the image sizes of the above table.
If the distance is less than 2 meters and more than 5 meters, the image could
be blurry.
Please check the following picture to show the trapezoid adjustment
Incorrect installation Correct installation Incorrect installation
English
Focus adjustment
1.Turn the lens clockwise to the projector then turn it counter clockwise slowly
. At the same time, check the resolution point carefully. When image is clear
(as the middle area of the image), it will be the best position of the lens.
NOTE:
When you replace the projector from a cold to a warm environment
water vapor might occur. Don't turn the projector on when this occurs but wait
until the vapor has disappeared.
KEYSTONE
If a projected picture has keystone distortion , correct image with keystone
adjustment. The image becomes trapezoid shape when the screen or
projector is not leveled. Please reposition the projector to improve its angle
to the screen . However , the circumference of the image may not be
focused.
English
Panel keyboard sketch map
1. Power key
It turns on or off the projector. The
function is the same as the "power" on
the remote control.
2. Sources
It chooses the input signal (such as:
AV, YPBPR, HDMI 1/2, USB1/2 or
PC)
3. Menu
4. Indicator light
Red color: standby
Green color: working
5. Direction operation Key
It adjusts the menu by Up/Down,
Left/Right.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Overmax Multipic 3.1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Overmax Multipic 3.1 in de taal/talen: Engels, Pools als bijlage per email.

De handleiding is 3,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info