492690
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
E
n
Enjoying Home Theater
The Home Theater means that you can enjoy surround sound with a real sense of movement in your own home — just like being in
a movie theater or concert hall.
Connecting the Speakers
Corner
position
1/3 of wall
position
Center speaker (SKC-770)
Position it close to your TV (preferably
on top) facing forward at about ear
level, or at the same height as the
front left and right speakers.
Front left and right speakers (SKF-770)
They should be positioned facing the listener at about ear level, and
equally spaced from the TV. Angle them inward slightly so as to
create a triangle, with the listener at the apex.
Surround left and right speakers (SKR-770)
Position them at the sides of the listener, or
slightly behind, about 2 to 3 feet (60 to 100 cm)
above ear level. Ideally they should be equally
spaced from the listener.
Subwoofer (SKW-770)
The subwoofer handles the bass sounds of the LFE (Low-Frequency
Effects) channel. The volume and quality of the bass output from your
subwoofer will depend on its position, the shape of your listening room,
and your listening position. In general, a good bass sound can be obtained
by installing the subwoofer in a front corner, or at one-third the way along
the front wall, as shown.
Red
White
Blue
Green
Front right speaker
Center speaker
Gray
Front left speaker
Surround right speaker
Surround left speaker
Powered
subwoofer
Speaker Connection Precautions
Read the following before connecting your
speakers:
Turn off your receiver before making any
connections.
Pay close attention to speaker
wiring polarity. Connect
positive (+) terminals to only
positive (+) terminals, and
negative (–) terminals to only
negative (–) terminals. If the speakers are
wired incorrectly, the sound will be out of
phase and will sound unnatural.
• Be careful not to short the positive and
negative wires. Doing so may damage
your amp.
Caution
With other audio-video components, connect
the subwoofer’s LINE INPUT to the subwoofer
pre out jack of your equipment. Never plug any
kind of musical instrument to the subwoofer.
Specifications
Powered Subwoofer (SKW-770)
Front Speakers (SKF-770)
Center Speaker (SKC-770)
Surround Speakers (SKR-770)
Specifications and appearance are subject to change without
prior notice.
Type: Bass-reflex
Input sensitivity/impedance: 140 mV / 20 k
Maximum output power: 290 W (Dynamic Power)
Frequency response: 25 Hz to 150 Hz
Cabinet capacity: 37 L (1.3 cubic feet)
Dimensions (W × H × D): 275 × 507 × 411 mm
(10-13/16" × 19-15/16" × 16-3/16")
(incl. projection)
Weight: 11.6 kg (25.6 lbs.)
Drivers unit: 25 cm (10") Cone Woofer × 1
Power supply: AC 220 V – 240V, 50/60 Hz
Power consumption: 137 W
Other: Auto Standby function
Type: 2 Way Bass-reflex
Impedance: 6
Maximum input power: 130 W
Sensitivity: 79.5 dB/W/m
Frequency response: 55 Hz to 50 kHz
Crossover frequency: 4 kHz
Cabinet capacity: 7.3 L (0.26 cubic feet)
Assembly dimensions (with supplied speaker base) (W × H × D):
262 × 1050 × 262 mm
(10-5/16" × 41-5/16" × 10-5/16")
(incl. projection)
Weight: 5.2 kg (11.5 lbs.) (incl. speaker base)
Drivers unit: 8 cm (3-1/4") cone (Woofer) × 2
2.5 cm (1") Balanced dome (Tweeter)
Terminal: Spring type color coded
Grille: Fixed
Type: 2 Way Bass-reflex
Impedance: 6
Maximum input power: 130 W
Sensitivity: 79 dB/W/m
Frequency response: 60 Hz to 50 kHz
Crossover frequency: 4 kHz
Cabinet capacity: 2.8 L (0.10 cubic feet)
Dimensions (W × H × D): 430 × 115 × 121 mm
(16-15/16" × 4-1/2" × 4-3/4")
(incl. grille and projection)
Weight: 2.2 kg (4.9 lbs.)
Drivers unit: 8 cm (3-1/4") Cone (Woofer) × 2
2.5 cm (1") Balanced dome (Tweeter)
Terminal: Spring type color coded
Keyhole slot: 2
Grille: Fixed
Type: Full-range closed box
Impedance: 6
Maximum input power: 130 W
Sensitivity: 81 dB/W/m
Frequency response: 80 Hz to 20 kHz
Cabinet capacity: 1.0 L (0.036 cubic feet)
Dimensions (W × H × D): 115 × 230 × 96 mm
(4-1/2" × 9-1/16" × 3-3/4")
(incl. grille and projection)
Weight: 1.0 kg (2.2 lbs.)
Drivers unit: 8 cm (3-1/4") Cone
Terminal: Spring type color coded
Keyhole slot: 1
Grille: Fixed
Attaching the Speaker Bases
Before you connect the speakers, attach the supplied
speaker base to each SKF-770.
1. Turn the speaker
upside down with the
protection cover
attached.
2. Align the speaker
base while the arrow
mark is headed in
the same direction as
the speaker’s face. Be
careful not to tip over
the speaker.
3. Align the screw holes
on the speaker base
with those on the
bottom of each
speaker, and affix the speaker base using the
supplied screws. Recommended torque is 10 kgf·cm
(9 lbf·in). Be careful not to tip over the speaker.
4. Turn the speaker right side up.
5. Remove the protection cover.
SAFETY PRECAUTIONS:
Attach the speaker bases in a manner that will not
allow the speakers to tip over.
Be sure to tighten the screws when you attach the
speaker bases.
Attach the speaker bases on a flat, level, and stable
floor.
After you attach the speaker bases, make sure that the
speakers stand upright and are stable.
Front speaker (SKF-770)
Front speakers
Speaker cables 11 ft. (3.5 m)
2 speaker bases and 8 screws
(Red)(White)
Speaker terminals
Caution:
The front grilles are not designed to be
removed so do not attempt to remove them
forcibly, as this will damage them.
Screws
Speaker base
Bottom of
SKF-770
Arrow mark
Protection cover
Wall Mounting
To mount the center speaker horizontally, use the two keyhole slots
shown to hang each speaker on two screws that are securely screwed
into the wall.
Using the Cork Stoppers for a More Stable Platform
We recommend using the supplied cork stoppers to achieve the best
possible sound from your speakers. The cork stoppers prevent the
speakers from moving, providing a more stable platform. Use
stoppers for the center speaker.
Center speaker (SKC-770)
Center speaker
Speaker cable 10 ft.
(3.0 m)
4 cork stoppers
(Green)
Speaker terminalsKeyhole slots
Caution:
The front grilles are not designed to be removed so do not attempt
to remove them forcibly, as this will damage them.
Keyhole slots for wall mounting
7-7/8" (200 mm)
Caution:
A mounting screw’s ability to support a speaker
depends on how well it’s anchored to the wall. If
you have hollow walls, screw each mounting
screw into a stud. If there are no studs, or the
walls are solid, use suitable wall anchors. Use
screws with a head diameter of 5/16" (8 mm) or
less and a shank diameter of 5/32" (4 mm) or
less. With hollow walls, use a cable/pipe
detector to check for any power cables or water
pipes before making any holes. Leave a gap of
between 7/32" (5 mm) and 3/8" (10 mm) between the wall and the
base of the screw head, as shown. (We recommend that you
consult a home installation professional.)
Wall
7/32" to 3/8"
(5 to 10mm)
Cork stoppers
Bottom of SKC-770
Wall Mounting
To mount the surround speakers
vertically, use the keyhole slot shown to
hang each speaker on a screw that’s
securely screwed into the wall.
Surround speaker
(SKR-770)
Surround speakers
Speaker cables 26 ft. (8.0 m)
(Blue)
(Gray)
Speaker
terminals
Keyhole slot
Caution:
The front grilles are not designed to be
removed so do not attempt to remove
them forcibly, as this will damage them.
Keyhole slot for
wall mounting
Caution:
A mounting screw’s
ability to support a
speaker depends on
how well it’s
anchored to the wall.
If you have hollow
walls, screw each
mounting screw into
a stud. If there are no
studs, or the walls are solid, use
suitable wall anchors. Use screws with
a head diameter of 5/16" (8 mm) or less
and a shank diameter of 5/32" (4 mm) or
less. With hollow walls, use a cable/pipe
detector to check for any power cables
or water pipes before making any holes.
Leave a gap of between 7/32" (5 mm)
and 3/8" (10 mm) between the wall and
the base of the screw head, as shown.
(We recommend that you consult a
home installation professional.)
Wall
7/32" to 3/8"
(5 to 10mm)
Setting the Subwoofer Level
To set the level of the subwoofer, use the OUTPUT LEVEL control.
Set it so that bass sounds are evenly balanced with the treble sounds
from the other speakers. Because our ears are less sensitive to very
low bass sounds, there’s a temptation to set the level of the
subwoofer too high. As a rule of thumb, set the subwoofer level to
what you think is the optimal level, and then back it off slightly.
Using the Floor Pads for Subwoofer
If the subwoofer is placed on a hard floor (wood,
vinyl, tile, etc.) and playback is very loud, the
subwoofer’s feet may damage the flooring. To
prevent this, place the supplied pads underneath
the subwoofer’s feet. The pads also provide a
stable base for the subwoofer.
Subwoofer (SKW-770)
Subwoofer
Power-plug adapter
Only supplied in certain countries. Use this
adapter if your AC outlet does not match with the
plug on the subwoofer’s power cord (adapter
varies from country to country).
RCA cable 10 ft. (3.0 m)
*How to mount the AC plug:
4 floor pads
Front
Rear
Note: The Auto Standby function turns the subwoofer on when the input signal
exceeds a certain level. If the Auto Standby function does not work reliably, try
slightly increasing or decreasing the subwoofer output level on your receiver.
*
STANDBY/ON indicator
Red: Subwoofer in standby mode
Blue: Subwoofer on
With the Auto Standby function, the SKW-770 automatically turns on
when an input signal is detected in Standby mode. When there’s no input
signal for a while, the SKW-770 automatically enters Standby mode.
SKW-770
ON
OFF
POWER
POWER switch
Press this switch to the ON position to turn on the
power. Press it to the OFF position to turn off the
power.
To AC outlet
OUTPUT LEVEL control
This control is used to adjust the volume of the
subwoofer.
LINE INPUT
This RCA input should be connected to the
subwoofer pre out on your AV receiver with
supplied RCA cable.
Pad
5.1ch Home Theater Speaker Package
SKS-HT728
Y1203-2
SN 29355763A
(C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved.
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
http://www.onkyo.com/
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.onkyochina.com/
1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,
China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.cn.onkyo.com/
*29355763A*
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Onkyo SKS-HT728 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Onkyo SKS-HT728 in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 0,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info