Handleiding Onkyo CS-725 (pagina 1 van 60) (Engels)

64966

Verklein

Vergroot

Pagina terug

1/60

Pagina verder

CD Receiver

CR-725

CR-725DAB

Instruction Manual

Thank you for purchasing an Onkyo CD receiver.

Please read this manual thoroughly before making

any connections and plugging it in.

Following the instructions in this manual will enable

you to obtain optimum performance and listening

enjoyment from your new CD receiver.

Please retain this manual for future reference.

Contents

Getting Started .......................... 2

Connections ............................ 15

Basic Operations .................... 26

Playing a Disc.......................... 29

Listening to the Radio ........... 38

Clock and Timer ...................... 49

Miscellaneous ......................... 56

Troubleshooting ................................56

If you can’t resolve an issue, try reset-

ting the CD receiver by holding down

the [2] button and pressing the

[STANDBY/ON] button.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radia-

tors, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-

cles, and the point where they exit from the appara-

tus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand,

tripod, bracket, or table spec-

ified by the manufacturer, or

sold with the apparatus.

When a cart is used, use cau-

tion when moving the cart/

apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

15. Damage Requiring Service

Unplug the apparatus from the wall outlet and refer

servicing to qualified service personnel under the

following conditions:

A. When the power-supply cord or plug is dam-

aged,

B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or

water,

D. If the apparatus does not operate normally by

following the operating instructions. Adjust

only those controls that are covered by the oper-

ating instructions as an improper adjustment of

other controls may result in damage and will

often require extensive work by a qualified tech-

nician to restore the apparatus to its normal

operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry

Never push objects of any kind into the apparatus

through openings as they may touch dangerous volt-

age points or short-out parts that could result in a

fire or electric shock.

The apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such as

vases shall be placed on the apparatus.

Don’t put candles or other burning objects on top of

this unit.

17. Batteries

Always consider the environmental issues and fol-

low local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation,

such as a bookcase or rack, ensure that there is ade-

quate ventilation.

Leave 20 cm (8") of free space at the top and sides

and 10 cm (4") at the rear. The rear edge of the shelf

or board above the apparatus shall be set 10 cm (4")

away from the rear panel or wall, creating a flue-

like gap for warm air to escape.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPARATUS TO

RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

AVIS

PORTABLE CART WARNING

S3125A

Precautions

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal with-

out the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not user-

serviceable. If you cannot turn on the unit, contact

your Onkyo dealer.

3. Care—Occasionally you should dust the unit all

over with a soft cloth. For stubborn stains, use a soft

cloth dampened with a weak solution of mild deter-

gent and water. Dry the unit immediately afterwards

with a clean cloth. Don’t use abrasive cloths, thin-

ners, alcohol, or other chemical solvents, because

they may damage the finish or remove the panel let-

tering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SEC-

TION CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the

voltage requirements printed on the unit’s rear panel

(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug

is readily operable (easily accessible) at all times.

Pressing the [STANDBY/ON] button to select

Standby mode does not fully shutdown the unit. If

you do not intend to use the unit for an extended

period, remove the power cord from the AC outlet.

5. Never Touch this Unit with Wet Hands—Never

handle this unit or its power cord while your hands

are wet or damp. If water or any other liquid gets

inside this unit, have it checked by your Onkyo

dealer.

6. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you origi-

nally bought it.

• Do not leave rubber or plastic items on this unit

for a long time, because they may leave marks on

the case.

• This unit’s top and rear panels may get warm

after prolonged use. This is normal.

• If you do not use this unit for a long time, it may

not work properly the next time you turn it on, so

be sure to use it occasionally.

• When you’ve finished using this unit, remove all

discs and turn off the power.

7. Installing this Unit

• Install this unit in a well-ventilated location.

• Ensure that there’s adequate ventilation all

around this unit, especially if it’s installed in an

audio rack. If the ventilation is inadequate, the

unit may overheat, leading to malfunction.

• Do not expose this unit to direct sunlight or heat

sources, because its internal temperature may

rise, shortening the life of the optical pickup.

• Avoid damp and dusty places, and places subject

to vibrations from loudspeakers. Never put the

unit on top of, or directly above a loudspeaker.

• Install this unit horizontally. Never use it on its

side or on a sloping surface, because it may cause

a malfunction.

• If you install this unit near a TV, radio, or VCR,

the picture and sound quality may be affected. If

this occurs, move this unit away from the TV,

radio, or VCR.

8. To Obtain a Clear Picture—This unit is a high-

tech, precision device. If the lens on the optical

pickup, or the disc drive mechanism becomes dirty

or worn, the picture quality may be affected. To

maintain the best picture quality, we recommend

regular inspection and maintenance (cleaning or

worn part replacement) every 1,000 hours of use

depending on the operating environment. Contact

your Onkyo dealer for details.

9. Moisture Condensation

Moisture condensation may damage this unit.

Read the following carefully:

Moisture may condense on the lens of the optical

pickup, one of the most important parts inside this

unit.

• Moisture condensation can occur in the following

situations:

– The unit is moved from a cold place to a warm

place.

– A heater is turned on, or cold air from an air

conditioner is hitting the unit.

– In the summer, when this unit is moved from

an air conditioned room to a hot and humid

place.

– The unit is used in a humid place.

• Do not use this unit when there’s the possibility

of moisture condensation occurring. Doing so

may damage your discs and certain parts inside

this unit.

If condensation does occur, remove all discs and leave

this unit turned on for two to three hours. By this time,

the unit will have warmed up and any condensation will

have evaporated.

This unit contains a semiconductor laser system and is

classified as a “CLASS 1 LASER PRODUCT”. So, to

use this model properly, read this Instruction Manual

carefully. In case of any trouble, please contact the store

where you purchased the unit.

To prevent being exposed to the laser beam, do not try to

open the enclosure.

Precautions—Continued

CAUTION:

CLASS 1M VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN. DO NOT VIEW

DIRECTLY WITH OPTICAL INSTRUMENTS.

THIS PRODUCT UTILIZES A LASER. USE OF CON-

TROLS OR ADJUSTMENTS OR PERFORMANCE

OF PROCEDURES OTHER THAN THOSE SPECI-

FIED HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

The label on the right is

applied on the rear panel.

1. This unit is a CLASS 1 LASER PRODUCT and

employs a laser inside the cabinet.

2. To prevent the laser from being exposed, do not

remove the cover. Refer servicing to qualified per-

sonnel.

For British models

Replacement and mounting of an AC plug on the power

supply cord of this unit should be performed only by

qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance

with the following code:

As the colours of the wires in the mains lead of this appa-

ratus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to

the terminal which is marked with the letter N or

coloured black.

The wire which is coloured brown must be connected to

the terminal which is marked with the letter L or

coloured red.

IMPORTANT

The plug is fitted with an appropriate fuse. If the fuse

needs to be replaced, the replacement fuse must

approved by ASTA or BSI to BS1362 and have the same

ampere rating as that indicated on the plug. Check for the

ASTA mark or the BSI mark on the body of the fuse.

If the power cord’s plug is not suitable for your socket

outlets, cut it off and fit a suitable plug. Fit a suitable fuse

in the plug.

For European Models

Features

Amplifier

• Onkyo VL Digital Technology

• Discrete Output Stage Circuitry

• Optimum Gain Volume Circuitry

• Direct Mode

• Super Bass (On/ Off) and Tone Control

• Gold-Plated 4 Audio Inputs and 2 Outputs

• Subwoofer Pre Out

—CR-725DAB only—

• Optical Digital Input

CD Player

• Plays CDs, MP3 CDs, CD-Rs and CD-RWs

• Wolfson 2ch Audio D/A Converter

• VLSC (Vector Linear Shaping Circuitry)

• 25 Track Programming

• Repeat Mode

Tuner & Other

• 4-Mode Timer (Play or Rec / Once or Every)

• Sleep Timer

• Battery-Free Memory Backup

• Headphone Jack

• Aluminium Front/Side panel and Volume knob

• Gold Plated Transparency Speaker Posts

• RI-Dock Compatible Remote Control (iPod Control

Capable)

• 40 FM Presets

—CR-725DAB only—

• 40 FM/DAB Presets

Blue: Neutral

Brown: Live

Declaration of Conformity

We,

ONKYO EUROPE

ELECTRONICS GmbH

LIEGNITZERSTRASSE 6,

82194 GROEBENZELL,

GERMANY

GROEBENZELL, GERMANY

ONKYO EUROPE ELECTRONICS GmbH

K. MIYAGI

declare in own responsibility, that the ONKYO product

described in this instruction manual is in compliance with the

corresponding technical standards such as EN60065,

EN55013, EN55020 and EN61000-3-2, -3-3.

*1. Make sure to use discs that have been finalized.

*2. VLSC and the VLSC logo are registered trademarks of Onkyo

Corporation.

* Apple and iPod are trademarks of Apple, Inc., registered in the

U.S. and other countries.

Supplied Accessories

Make sure you have the following accessories:

* In catalogs and on packaging, the letter at the end of the product

name indicates the color. Specifications and operations are the

same regardless of color.

Before Using the CD

Receiver

Notes:

• If the remote controller doesn’t work reliably, try

replacing the batteries.

• Don’t mix new and old batteries or different types of

batteries.

• If you intend not to use the remote controller for a long

time, remove the batteries to prevent damage from

leakage or corrosion.

• Expired batteries should be removed as soon as possi-

ble to prevent damage from leakage or corrosion.

Remote controller and two batteries (R6/AA)

Indoor FM antenna

DAB antenna (CR-725DAB only)

Installing the Batteries

Detach the battery cover by pressing the

tab and pulling up the cover.

Insert two batteries (R6/AA) into the bat-

tery compartment.

Carefully follow the polarity diagram (positive

(+) and negative (–) symbols) inside the battery

compartment.

After the batteries are installed and

seated correctly, attach the compartment

cover.

Contents

Getting Started

Important Safety Instructions.....................................2

Precautions................................................................ 3

Features ....................................................................4

Supplied Accessories ................................................ 5

Before Using the CD Receiver ..................................5

Installing the Batteries ........................................... 5

Getting to Know the CD Receiver..............................7

Front Panel ............................................................7

Display ...................................................................8

Rear Panel.............................................................9

Remote Controller................................................10

Using the Remote Controller ...............................11

Disc Notes ...............................................................13

Connections

Connecting Antennas ..............................................15

Connecting Speakers ..............................................17

Connecting Other Components ...............................18

About Connections .............................................. 18

Cables and Jacks ................................................18

Connecting a Subwoofer .....................................18

Connecting an Onkyo Cassette Deck..................19

Connecting an Onkyo MD Recorder....................20

Connecting an Onkyo CD Recorder ....................21

Connecting a Component with a

Digital Audio Output (CR-725DAB only) ...........22

Connecting an Onkyo RI Dock (Remote Interactive

Dock).................................................................23

Connecting a TV ..................................................23

Connecting a Portable Audio Device ...................24

Connecting the Power Cord ....................................24

First Time Setup (European models only) ...............25

Setting the Clock with the AccuClock Function ...25

Basic Operations

Basic Operations .....................................................26

Turning On the CD Receiver ...............................26

Adjusting the Volume...........................................26

Selecting the Input Source...................................26

Using Headphones ..............................................26

Adjusting the Bass and Treble.............................27

Using the Super Bass Function ...........................27

Using the Direct Function ....................................27

Muting the Sound.................................................27

Changing the Input Display..................................28

Playing a Disc

Playing CDs.............................................................29

Using the Remote Controller ...............................30

Displaying CD Information ...................................30

Selecting/Playing MP3 Files ................................31

Displaying MP3 Information.................................33

Memory Playback ................................................34

Random Playback................................................35

Repeat Playback..................................................35

Setting MP3 Preferences.....................................36

Listening to the Radio

Listening to the Radio ..............................................38

Tuning into FM Radio Stations.............................38

Displaying Radio Information ...............................39

Receiving RDS.....................................................39

Listening to DAB Digital Radio

(CR-725DAB only).............................................40

Presetting FM Stations Automatically

(Auto Preset) .....................................................43

Presetting FM/DAB Stations Manually.................44

Selecting Preset Stations.....................................45

Naming Presets ...................................................46

Copying Presets...................................................47

Erasing a Preset’s Name .....................................48

Erasing Presets....................................................48

Clock and Timer

Setting the Clock......................................................49

Setting AccuClock to Use a Specific Station........49

Setting the Clock Manually ..................................50

Using the Timers......................................................51

About the Timers..................................................51

Programming the Timers .....................................52

Turning Timers On and Off ..................................54

Checking Timer Settings......................................54

Using the Sleep Timer .........................................55

Miscellaneous

Troubleshooting .......................................................56

Specifications...........................................................59

Getting to Know the CD Receiver

The page numbers in parentheses show where you can find the main explanation for each item.

a STANDBY indicator (24, 26)

Lights up in Standby mode.

b STANDBY/ON button (26, 50, 53, 56)

Sets the CD receiver to On or Standby.

c Remote control sensor (11)

Receives control signals from the remote controller.

d Display

See “Display” on page 8.

e VOLUME control (26) and indicator

This control is used to adjust the volume of the CD

receiver to “Min”, “1” through “41”, “Max”.

The volume control indicator lights up when the CD

receiver is on.

f PHONES jack (26)

This stereo minijack is for connecting a pair of ste-

reo headphones for private listening.

g LINE 2 IN jack

This stereo minijack is for connecting an audio

source, such as an MP3 music player or personal

computer.

h Disc tray (29)

The CD is loaded here.

i INPUT button (26, 28, 43, 45)

Used to select the input source.

j DIRECT button (27)

Used with the Direct function.

The DIRECT button’s indicator lights up when the

Direct function is on.

k TONE button (27)

Used to adjust the bass and treble.

l Multi control (29, 45)

Used to select radio presets, tracks, and MP3 fold-

ers. Also used to select and set various functions

and settings.

m Open/Close [0] button (29)

Used to open and close the disc tray.

n Stop [2] button (29, 56)

Stops CD playback.

o Play/Pause [1/3] button (29)

Starts CD playback. Pressing it during playback

pauses playback.

Front Panel

123 54

bn bo bp98 bk bl bm

Getting to Know the CD Receiver—Continued

a SLEEP indicator

Lights up when the Sleep function has been set.

b MP3 indicator

Lights up when an MP3 CD is loaded.

c PCM indicator (CR-725DAB only)

Lights up when the digital input signal received by

the OPTICAL DIGITAL IN jack is PCM. It flashes

if the signal is not PCM or the CD receiver is not

locked to the incoming digital signal.

d FOLDER indicator

Lights up while the number of an MP3 folder is

being displayed.

e DIRECT indicator

Lights up when the Direct function is on.

f S.BASS indicator

Lights up when the Super Bass function is on.

g MUTING indicator

Flashes while the CD receiver is muted.

h Playback mode indicators

1FOLDER:

Lights up when 1-folder playback is selected.

MEMORY:

Lights up when memory playback is selected.

RANDOM:

Lights up when random playback is selected.

REPEAT:

Lights up when repeat playback is selected for all

tracks.

REPEAT 1:

Lights up when repeat playback is selected for one

track.

i Play and pause 1/3 indicators

The Play 1 indicator lights up for playback. The

Pause 3 indicator lights up while playback is

paused.

j TIMER indicators

Show the status of the timers.

TIMER:

Lights up when a timer has been programmed.

1, 2, 3, 4:

Light up when a timer has been programmed.

Lights up when a timer has been programmed for

recording.

k Tuning indicators

AUTO:

Lights up when Auto Tuning is selected, and disap-

pears when Manual Tuning is selected.

Lights up when the CD receiver is tuned to a radio

station.

DAB (CR-725DAB only):

Lights up when the CD receiver is tuned to a DAB

digital radio station.

FM ST:

Lights up when the CD receiver is tuned to a stereo

FM station.

Lights up when the CD receiver is tuned to a radio

station that supports RDS (Radio Data System).

l FILE indicator

Lights up when an MP3 file number is being dis-

played.

m TRACK indicator

Lights up when a CD track number is being dis-

played.

n TITLE, ARTIST and ALBUM indicators

TITLE indicator lights up when the title (ID3 tag) of

a music file is being displayed.

ARTIST indicator lights up when the artist name

from a music file (ID3 tag) is being displayed.

ALBUM indicator lights up when the album name

from a music file (ID3 tag) is being displayed.

o DISC, TOTAL, and REMAIN indicators

These indicators light up when the total time or the

remaining disc or track time is being displayed.

p Message area

Various information is displayed here, including

radio preset numbers, tuning frequency, current

time, volume level, sleep time, mode settings, and

so on.

Display

12 5467

bn bo bp9

bk bl bm bq

* CR-725DAB

only

RDS: RDS is only available in areas where

RDS broadcasts are available.

Getting to Know the CD Receiver—Continued

The page numbers in parentheses show where you can find the main explanation for each item.

a LINE 1 IN (23)

This analog audio input is for connecting a compo-

nent with an analog output, such as a TV, or a turn-

table with a built-in phono equalizer.

b MD/TAPE IN/OUT (19, 20)

These analog audio inputs and outputs are for con-

necting a recorder with an analog input and output,

such as a MiniDisc recorder or cassette deck.

c DAB ANTENNA (CR-725DAB only) (15)

This jack is for connecting a DAB antenna.

d FM ANTENNA (15, 16)

This jack is for connecting an FM antenna.

e SUBWOOFER PRE OUT (18)

This jack is for connecting a powered subwoofer.

f SPEAKERS (17)

These terminal posts are for connecting speakers.

g u REMOTE CONTROL (19–23)

This u (Remote Interactive) jack can be con-

nected to an u jack on another Onkyo component.

The CD receiver’s remote controller can then be

used to control that component. To use u, you

must make an analog audio connection (RCA)

between the CD receiver and the other component,

even if they are connected digitally.

h OPTICAL DIGITAL IN (CR-725DAB only) (22)

This optical digital audio input can be used to con-

nect a component with an optical digital output,

such as a CD recorder, MD recorder, games con-

sole, satellite tuner, or personal computer. Use a

commercially available optical digital audio cable to

make the connection.

i DOCK/CDR IN/OUT (21, 23)

These analog audio inputs and outputs are for con-

necting a recorder with an analog input and output

such as a CD recorder, or an Onkyo RI Dock.

j Power cord (24)

The power cord should be connected to a suitable

power source (Plug type varies from country to

country).

Rear Panel

123 4 5 6

78 9 bk

* CR-725DAB only

See pages 15–24 for connection information.

Getting to Know the CD Receiver—Continued

The page numbers in parentheses show where you can

find the main explanation for each item.

a STANDBY/ON button (26, 50, 53)

This button is used to set the CD receiver to On or

Standby.

b SLEEP button (55)

Used to set the Sleep timer, which turns off the CD

receiver after a specified time.

c Number buttons (30, 32, 34, 45, 46, 52)

Used to select tracks and radio presets. Also used to

set the clock manually, set the timers, and enter

names for radio presets. Can also be used with an

Onkyo RI Dock or CD recorder.

d TIMER button (25, 49, 50, 52, 54)

Used to set the timers and clock.

e MENU/NO/CLEAR button (28, 36, 42–44,

46–48)

Used with various functions and settings for select-

ing, cancelling, and deleting. With an Onkyo CD

recorder, it works as a clear button. With an Onkyo

RI Dock, it works as a mode button.

f Previous/Next [7]/[6] and

[e PRESET]/[PRESET r] buttons (30, 40,

42, 45)

Used to select the previous or next track or radio

preset. Can also be used with an Onkyo RI Dock or

CD recorder. With an Onkyo cassette deck, they

work as rewind and fast forward buttons.

g Fast Reverse/Fast Forward [5]/[4] and

[e TUN]/[TUN r] buttons (30, 38, 41, 49)

Used to fast reverse or fast forward CD playback.

Can also be used with an Onkyo RI Dock or CD

recorder. Also used to tune the radio and edit preset

names.

h CD control buttons (30)

3 : Pauses playback.

2 : Stops playback.

1: Starts playback.

i VOLUME [q/w] buttons (26, 30)

Adjust the volume level.

j S.BASS button (27)

Sets the Super Bass function.

k Onkyo RI Dock and CD recorder control

buttons

3 : Pauses playback or recording.

2 : Stops playback or recording.

1: Starts playback or resumes recording.

Remote Controller

Getting to Know the CD Receiver—Continued

l Onkyo MD recorder and cassette deck

control buttons

For twin cassette decks, only Deck B can be con-

trolled.

t: Plays side B (cassette deck).

3 : Pauses playback or recording (MD).

2 : Stops playback, recording, fast-forward, or

rewind.

1: Plays side A.

m CLOCK CALL button (50)

Calls up the clock to display the day and time.

n INPUT [t]/[1] buttons (26, 28, 43, 45)

Used to select the input source.

o DISPLAY button (30, 33, 39, 41, 46, 50)

Used to change the information shown on the dis-

play. Also used to select characters when naming

radio presets. Can also be used with an Onkyo CD

recorder. With an Onkyo RI Dock, it works as a

backlight button.

Push and hold for 5 seconds to enter Dimmer1

mode. Repeat and hold for another 5 seconds to

enter Dimmer2 mode. Repeat again to return to the

original setting.

p FOLDER button (31, 32, 33, 37)

Used to select MP3 folders.

q REPEAT button (35)

Sets repeat playback. Can also be used with an

Onkyo RI Dock or CD recorder. With an Onkyo

cassette deck, it works as a reverse mode button.

r TONE button (27)

Used to adjust the bass and treble.

s YES/MODE/SHUFFLE button (33–35, 38)

Used with various functions and settings for con-

firming, selecting modes, and selecting random

playback. Can also be used with an Onkyo RI Dock,

it works as a shuffle button.

t ENTER button

Used to confirm various functions and settings. Can

also be used with an Onkyo RI Dock or CD

recorder.

u MUTING button (27)

Mutes the output of the CD receiver.

v TUNER/BAND button (38, 40, 43, 45)

Selects FM, or DAB radio as the input source.

When you operate the remote controller, point it at the

CD receiver’s remote control sensor, as shown below.

Notes:

• The remote controller may not work reliably if the CD

receiver is subjected to bright light, such as direct sun-

light or inverter-type fluorescent lights. Keep this in

mind when installing.

• If another remote controller of the same type is used in

the same room, or the CD receiver is installed close to

equipment that uses infrared rays, the remote control-

ler may not work reliably.

• Don’t put anything, such as a book, on the remote con-

troller because the buttons may be pressed inadvert-

ently, thereby draining the batteries.

• The remote controller may not work reliably if the CD

receiver is installed in a rack behind colored glass

doors. Keep this in mind when installing.

• The remote controller will not work if there’s an

obstacle between it and the CD receiver’s remote con-

trol sensor.

Using the Remote Controller

Remote control sensor

CD receiver

Getting to Know the CD Receiver—Continued

Controlling an Onkyo MD Recorder, Cassette Deck, or RI Dock

Explanation of buttons for using the Onkyo MD recorder, cassette deck, RI Dock, or CD recorder when connected

to the MD/TAPE jack, DOCK/CDR or OPTICAL DIGITAL IN (CR-725DAB only) jack of the CD receiver.

• See pages 19-23 for instructions on connecting the components.

• Connecting an Onkyo component to the CD receiver with an u cable allows you to control the component with the

CD receiver’s remote controller. In addition, when playback is started on the component, the CD receiver will auto-

matically select it as the input source.

• It will also be necessary to change the input display titles to correspond to the equipment that is connected (see

page 28).

Example: Shows the case of h:

the [YES/MODE/SHUFFLE] button.

• When the cassette deck is connected to the MD/TAPE

jack of the CD receiver and the input source is set to

“TAPE”, it works as a DOLBY NR button.

• When the CD recorder is connected to the

DOCK/CDR IN/OUT jack of the CD receiver and the

input source is set to “DOCK”, it operates as the

SHUFFLE button; when the input source is set to

“CD-R”, it operates as the MODE button.

The operation of the buttons is the same when the CD

recorder is connected to the OPTICAL DIGITAL IN

jack, and the input source is set to “CD-R/dig”.

• Refer to the instruction manual for each connected component for details. For column items with no notation: buttons

will not function when pressed.

Jack MD/TAPE DOCK/CDR DIGITAL IN

TAPE MD DOCK CD-R CD-R/dig

1 ~ 9 1 ~ 9 1 ~ 9 1 ~ 9

0 10/0 10/0 10/0

>10 >10 >10 >10

MENU/NO/CLEAR CLEAR MODE CLEAR CLEAR

ENTER ENTER SELECT ENTER ENTER

DOCK/CDR 1 111

DOCK/CDR 2 222

DOCK/CDR 3 333

MD/TAPE 111

MD/TAPE 222

MD/TAPE 3 (t) t3

DISPLAY DISPLAY BACKLIGHT DISPLAY DISPLAY

REPEAT REV MODE REPEAT REPEAT REPEAT REPEAT

YES/MODE/SHUFFLE DOLBY NR MODE

SHUFFLE

*1. In “Cursor Mode” it works as a MENU button.

MODE MODE

7/65/47/6

7/6

*2. In “Cursor Mode” it can be used for navigation menus.

7/67/6

5/45/45/45/45/4

Button

Input source

Disc Notes

Supported Discs

The CD receiver supports the following discs.

• Some audio CDs use copy protection that doesn’t con-

form to the official CD standard. Since these are non-

standard discs, they may not play properly in the CD

receiver.

• The CD receiver supports 8 cm and 12 cm discs.

• The CD receiver does not support disc types not listed.

• Don’t use discs with an unusual shape, such as those

shown below, as you may damage the CD receiver.

• Don’t use discs that have residue from adhesive tape,

rental discs with peeling labels, or discs with custom-

made labels or stickers. Doing so may damage the CD

receiver and you may not be able to remove the disc

properly.

CD-R/RW Compatibility

• The CD receiver supports CD-R and CD-RW discs.

However, some CD-R and CD-RW discs may not

work properly for any of the following reasons: disc

burner characteristics, disc characteristics, the disc is

damaged or dirty. See the manual supplied with your

disc burner for more information. Condensation or dirt

on the optical pickup lens can also affect playback.

• Make sure to use discs that have been finalized.

Discs Made on Personal Computers

Discs made on personal computers, including those of a

compatible format, may not work properly in the CD

receiver because of incorrect settings in the disc burning

software. Check the manuals supplied with your disc

burning software for additional compatibility informa-

tion.

MP3 Compatibility

• MP3 discs must be ISO 9660 Level 1 or Level 2,

Romeo or Joliet compliant. Supported formats:

Mode 1, Mode 2 XA Form 1.

• Folders can be up to eight levels deep.

• MP3 files must be MPEG-1/MPEG-2 Audio Layer 3

format with a sampling rate of between 8 kHz and

48 kHz and a bit-rate of between 8 kbps and 320 kbps

(128 kbps recommended). Incompatible files cannot

be played.

• Constant bit rate MP3 files are recommended, how-

ever, variable bit-rate (VBR) MP3 files between

8 kbps and 320 kbps are supported. (Playing times

may not display correctly.)

• MP3 files must have a “.mp3” or “.MP3” file name

extension. MP3 files without the proper extension will

not be recognized. To prevent noise and malfunction,

do not use these extensions for other types of files.

• The CD receiver supports up to 499 MP3 files and

folders. Files and folders in excess of this cannot be

played. Note that if the file and folder structure is very

complicated, the CD receiver may not be able to read

or play all of the MP3 files on the disc.

• Disc, file, and folder names may contain up to 32 char-

acters.

• The maximum time that can be displayed for a single

file is 99 minutes and 59 seconds.

• The remaining time cannot be displayed when playing

MP3 files.

• MP3 file and folder names (excluding the extension)

are shown on the display.

• Multisession discs are supported, however, some mul-

tisession discs may take a long time to load and some

may not load at all. When burning CDs, we recom-

mend that you use a single-session (disc-at-once), and

select “Disc Close.”

• Normally, the music in the audio session of a CD Extra

disc is played. However, you can set the CD receiver

so that it plays any MP3 files in the data session of a

CD-R/RW disc instead. If the data session contains no

MP3 files, the audio session will be played regardless.

See “Setting MP3 Preferences” on page 36 for more

information.

• The Emphasis is not supported.

Disc Logo Format or file type

Audio CD PCM

CD-R

Audio CD, MP3

MP3

CD-RW

Audio CD, MP3

MP3

CD Extra

Audio CD (Session 1),

MP3 (Session 2)

Disc Notes—Continued

• The following ID3 tags are supported: versions 1.0/1.1

and 2.2/2.3/2.4. Versions 2.5 and later are not sup-

ported. Normally, version 2.2/2.3/2.4 tags have prior-

ity and will be displayed regardless of the ID3 VER 1

preference on page 36.

• For ID3 version 2 tags, the tag information recognized

will be those embedded in the beginning of the file.

We recommend that you include only title, artist

name, and album name information in ID3 tags. Com-

pressed, encrypted, and unsynchronized ID3 tags can-

not be displayed.

Note:

With CD-ROM, CD-R, and CD-RW discs that contain

many files and folders and files other than MP3s, it may

take a long time to read the disc. We recommend that you

include only MP3 files on your discs, use about 20 fold-

ers, and limit folder nesting to three levels deep.

Disc Content Organization

■ CD

CDs contain tracks.

■ MP3

MP3 discs contain MP3 files organized into folders.

Handling Discs

• Never touch the underside of a disc. Always hold discs

by the edge, as shown.

• Never attach adhesive tape or sticky labels to discs.

Cleaning Discs

• For best results, keep your discs clean. Fingerprints

and dust can affect the sound quality and should be

removed as follows. Using a clean soft cloth, wipe

from the center outwards, as shown. Never wipe in a

circular direction.

• To remove stubborn dust or dirt, wipe the disc with a

damp soft cloth, and then dry it with a dry cloth.

• Never use solvent-based cleaning fluids, such as thin-

ner or benzine, commercially available cleaners, or

antistatic sprays intended for vinyl records, as they

may damage the disc.

Storing Discs

• Don’t store discs in places subject to direct sunlight or

near heat sources.

• Don’t store discs in places subject to moisture or dust,

such as in a bathroom or near a humidifier.

• Always store discs in their cases and vertically. Stack-

ing, or putting objects on unprotected discs may cause

warping, scratches, or other damage.

Track 2 Track 3 Track 4Track 1

Audio CD

Track 5

Folder 1

Folder 2

File 2 File 3 File 1File 1 File 2

MP3 (CD-R/CD-RW)

Underside

✔

Connecting Antennas

This section explains how to connect the supplied indoor

FM antenna and DAB antenna (CR-725DAB only), and

how to connect commercially available outdoor FM

antenna.

The CD receiver won’t pick up any radio signals without

an antenna connected, so you must connect the antenna

to use the tuner.

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

If you cannot achieve good reception with the supplied

indoor FM antenna, try a commercially available out-

door FM antenna instead (see page 16).

Connecting the DAB Antenna (CR-725DAB

only)

Attach the FM antenna, as shown.

Once the CD receiver is ready for use, you’ll need

to tune into an FM radio station and adjust the

position of the FM antenna to achieve the best

possible reception.

Use thumbtacks or something similar to

fix the FM antenna into position.

Caution: Be careful that you don’t injure yourself

when using thumbtacks.

FM ANTENNA jack

DAB ANTENNA jack

(CR-725DAB only)

Insert the plug fully

into the jack.

Thumbtacks, etc.

Screw the supplied DAB antenna’s plug

onto the DAB ANTENNA jack.

Once the CD receiver is ready for use, you’ll

need to tune into a DAB station and adjust the

position of the DAB antenna to achieve the best

possible reception.

Use thumbtacks or something similar to

fix the DAB antenna into position.

Connecting Antennas—Continued

Connecting an Outdoor FM Antenna

If you cannot achieve good reception with the supplied

indoor FM antenna, try a commercially available out-

door FM antenna instead.

Notes:

• Outdoor FM antennas work best outside, but usable

results can sometimes be obtained when installed in an

attic or loft.

• For best results, install the outdoor FM antenna well

away from tall buildings, preferably with a clear line

of sight to your local FM transmitter.

• Outdoor antenna should be located away from possi-

ble noise sources, such as neon signs, busy roads, etc.

• For safety reasons, outdoor antenna should be situated

well away from power lines and other high-voltage

equipment.

• Outdoor antenna must be grounded in accordance

with local regulations to prevent electrical shock haz-

ards.

■ Using a TV/FM Antenna Splitter

It’s best not to use the same antenna for both FM and TV

reception, as this can cause interference problems. If cir-

cumstances demand it, use a TV/FM antenna splitter, as

shown.

To CD receiver To TV (or VCR)

TV/FM antenna splitter

Connecting Speakers

Connecting Your Speakers

• Connect the right speaker to the CD receiver’s right (R) SPEAKERS terminals. Connect the left speaker to the left

(L) SPEAKERS terminals.

• Connect the positive (+) terminal on each speaker to the corresponding positive (+) terminal on the CD receiver.

Connect the negative (–) terminal on each speaker to the corresponding negative (–) terminal on the CD receiver. Use

the red wires to connect the positive (+) terminals.

• Connect only speakers with an impedance of between

4 and 16 ohms. Connecting a speaker with a lower

impedance may damage the speaker.

• Be careful not to short the positive and negative wires.

Doing so may damage the CD receiver.

• Do not connect both speaker cables to the same L or R

terminals (Fig. 1). Do not connect more than two

speaker terminals to each speaker (Fig. 2).

SPEAKERS

Red wires

Right speaker

Left speaker

Speaker

cable

—Terminal posts—

Strip about 15 mm of insulation from the ends of the speaker cables,

and twist the bare wires tightly. Unscrew the terminal. Fully insert the

bare wire, making sure that it’s touching the threaded shaft in the center.

Screw the terminal tight.

SPEAKERS

Fig. 1 Fig. 2

Connecting Other Components

• Before making any connections, read the manuals

supplied with your other components.

• Don’t connect the power cord until you’ve completed

and double-checked all connections.

Connection Color Coding

RCA-type audio connections are usually color-coded:

red and white. Use red plugs to connect right-channel

audio inputs and outputs (typically labeled “R”). Use

white plugs to connect left-channel audio inputs and out-

puts (typically labeled “L”).

• Push plugs in all the way to make

good connections (loose connec-

tions can cause noise or malfunc-

tions).

• To prevent interference, keep

audio cables away from power

cords and speaker cables.

Optical Digital Jack (CR-725DAB only)

The CD receiver’s optical digital jack has a shutter-type

cover that opens when an optical plug is inserted and

closes when it’s removed. Push the plug in all the way.

Caution:

To prevent shutter damage, hold the optical plug straight

when inserting and removing.

Note:

Do not put anything on top of the CD receiver, as it may

interfere with proper ventilation.

No connecting cables are included with the CD receiver.

The CD receiver has a SUBWOOFER PRE OUT jack for connecting a powered subwoofer (i.e., a subwoofer with a

built-in amplifier).

About Connections

Left (white)

Right (red)

Analog audio

cable

Left (white)

Right (red)

Right!

Wrong!

Cables and Jacks

Cable Jack Description

Analog audio cable

(RCA)

This cable carries analog audio.

Optical digital audio

cable (CR-725DAB

only)

This cable carries digital audio.

Stereo miniplug

cable

This cable carries analog audio.

OPTICAL

Connecting a Subwoofer

: Signal flow

Powered subwoofer

CD receiver

Connecting Other Components—Continued

The following diagram shows how to connect an optional Onkyo cassette deck.

Connect the CD receiver’s MD/TAPE OUT jacks to the cassette deck’s INPUT (REC) jacks, and connect the CD

receiver’s MD/TAPE IN jacks to the cassette deck’s OUTPUT (PLAY) jacks.

What can you do with u?

• Connecting an Onkyo cassette deck to the CD receiver with an u cable allows you to control the cassette deck with

the CD receiver’s remote controller. In addition, when playback is started on the cassette deck, the CD receiver will

automatically select it as the input source.

• To use u, you must connect the Onkyo cassette deck to the CD receiver with an u cable and an analog audio cable

(RCA). In addition, the Input Display for the MD/TAPE jacks must be set to “TAPE.” Since this is the default setting,

unless you’ve changed it, it can be left as it is (see page 28).

•Some u-capable components have two u jacks. They’re both the same, so you can use either one. The extra jack

is for connecting additional u-capable components.

Notes:

• When listening to the audio of a component connected to the CD receiver but with no u connection, select TAPE

input source.

• It is also possible to connect the MD/TAPE jacks to a DAT recorder. When connected to a DAT recorder, set the Input

Display to “DAT” (see page 28).

• The MD/TAPE IN jacks can be connected to the audio output jack of a VCR. The VCR video output jack should be

connected to a TV. When the CD receiver is connected to a VCR, set the Input Display to “VIDEO” (see page 28).

Connecting an Onkyo Cassette Deck

LINE 1

MD/

TAPE

OUT

DOCK/

CDR

(REC) (PLAY)

INPUT OUTPUT

REMOTE

CONTROL

Onkyo cassette deck’s

rear panel

Analog audio cables (RCA)

u cable supplied with

the Onkyo cassette deck

White

Red

White

Red Red

Red

White White

CD receiver’s

rear panel

: Signal flow

Connecting Other Components—Continued

The following diagram shows how to connect an optional Onkyo MD recorder.

Connect the CD receiver’s MD/TAPE OUT jacks to the MD recorder’s INPUT (REC) jacks, and connect the CD

receiver’s MD/TAPE IN jacks to the MD recorder’s OUTPUT (PLAY) jacks.

What can you do with u?

• Connecting an Onkyo MD recorder to the CD receiver with an u cable allows you to control the MD recorder with

the CD receiver’s remote controller. In addition, when playback is started on the MD recorder, the CD receiver will

automatically select it as the input source.

• To use u, you must connect the Onkyo MD recorder to the CD receiver with an u cable and an analog audio cable

(RCA). In addition, the Input Display for the MD/TAPE jacks must be set to “MD” (see page 28).

•Some u-capable components have two u jacks. They’re both the same, so you can use either one. The extra jack

is for connecting additional u-capable components.

Note:

• When listening to the audio of a component connected to the CD receiver but with no u connection, select TAPE

input source.

• It is also possible to connect the MD/TAPE jacks to a DAT recorder. When connected to a DAT recorder, set the Input

Display to “DAT” (see page 28).

• The MD/TAPE IN jacks can be connected to the audio output jack of a VCR. The VCR video output jack should be

connected to a TV. When the CD receiver is connected to a VCR, set the Input Display to “VIDEO” (see page 28).

Connecting an Onkyo MD Recorder

LINE 1

MD/

TAPE

OUT

DOCK/

CDR

(REC) (PLAY)

INPUT OUTPUT

REMOTE

CONTROL

Onkyo MD recorder’s

rear panel

Analog audio cables (RCA)

u cable supplied with

the Onkyo MD recorder

White

Red

White

Red Red

Red

White White

CD receiver’s

rear panel

: Signal flow

Connecting Other Components—Continued

The following diagram shows how to connect an optional Onkyo CD recorder.

Connect the CD receiver’s DOCK/CDR OUT jacks to the CD recorder’s INPUT (REC) jacks, and connect the CD

receiver’s DOCK/CDR IN jacks to the CD recorder’s OUTPUT (PLAY) jacks.

What can you do with u?

• Connecting an Onkyo CD recorder to the CD receiver with an u cable allows you to control the CD recorder with

the CD receiver’s remote controller. In addition, when playback is started on the CD recorder, the CD receiver will

automatically select it as the input source.

• To use u, you must connect the Onkyo CD recorder to the CD receiver with an u cable and an analog audio cable

(RCA). In addition, the Input Display for the DOCK/CDR jacks must be set to “CDR” (see page 28).

•Some u-capable components have two u jacks. They’re both the same, so you can use either one. The extra jack

is for connecting additional u-capable components.

Connecting an Onkyo CD Recorder

LINE 1

MD/

TAPE

OUT

DOCK/

CDR

(REC) (PLAY)

INPUT OUTPUT

REMOTE

CONTROL

: Signal flow

Onkyo CD recorder’s

rear panel

Analog audio cable (RCA)

u cable supplied with

the Onkyo CD recorder

White

Red

White

Red Red

Red

White White

CD receiver’s

rear panel

Connecting Other Components—Continued

The following diagram shows how to connect a component with an optical digital audio output, such as a CD recorder,

MD recorder, games console, satellite tuner, or personal computer.

Connect the CD receiver’s OPTICAL DIGITAL IN jack to an optical digital audio output on the other component.

You can change the Input Display for the OPTICAL DIGITAL IN to DIGITAL, CDR, PC, or GAME so that it matches

the type of component that you connect (see page 28).

Connecting an Onkyo Component with a Digital Audio Output

The following diagram shows how to connect an Onkyo component with an optical digital audio output.

Connect the CD receiver’s OPTICAL DIGITAL IN jack to an optical digital audio output on the Onkyo component.

What can you do with u?

• Connecting an Onkyo component to the CD receiver with an u cable allows you to control the component with the

CD receiver’s remote controller. In addition, when playback is started on the component, the CD receiver will auto-

matically select it as the input source.

• To use u, you must connect the Onkyo component to the CD receiver with an u cable and an analog audio cable

(RCA). In addition, you must change the Input Display for the DIGITAL IN so that it matches the type of component

that you connect. When you connect a CD recorder to the DOCK/CDR jacks and OPTICAL DIGITAL IN jack, you

must set the Input Display for DOCK/CDR to “CD-R,” and set the Input Display for OPTICAL DIGITAL IN to “CD-

R/dig” (see page 28).

• If you connect an audio processor such as the Onkyo UE-205, you must set the Input Display for DOCK/CDR to

“PC,” and set the Input Display for OPTICAL DIGITAL IN to “PC/dig,” otherwise the wrong input source may be

selected when playback starts (see page 28).

•Some u-capable components have two u jacks. They’re both the same, so you can use either one. The extra jack

is for connecting additional u-capable components.

Connecting a Component with a Digital Audio Output (CR-725DAB only)

DIGITAL

OUTPUT

Satellite tuner, CD

recorder, etc.

Optical digital audio cable

: Signal flow

CR-725DAB’s

rear panel

Personal computer

MD/

TAPE

OUT

DOCK/

CDR

REMOTE

CONTROL

DIGITAL

OUTPUT

(REC) (PLAY)

INPUT OUTPUT

Onkyo component with a

digital audio output

u cable

: Signal flow

Optical digital audio cable

CR-725DAB’s

rear panel

Analog audio cable (RCA)

Red

White

Red Red

Red

White White

Connecting Other Components—Continued

The following diagram shows how to connect an optional Onkyo RI Dock (Remote Interactive Dock).

Connect the CD receiver’s DOCK/CDR IN jacks to the RI Dock’s AUDIO OUT jacks.

What can you do with u?

• Connecting an Onkyo RI Dock to the CD receiver with an u cable allows you to control the RI Dock with the CD

receiver’s remote controller. In addition, when playback is started on the RI Dock, the CD receiver will automatically

select it as the input source.

• To use u, you must connect the Onkyo RI Dock to the CD receiver with an u cable and an analog audio cable

(RCA). On the RI Dock, set the RI MODE switch to “HDD”or “HDD/DOCK”. See the RI Dock’s instruction manual

for details.

• To use u, the Input Display for the DOCK/CDR jacks must be set to “DOCK.” Since this is the default setting,

unless you’ve changed it, it can be left as it is (see page 28).

Connect the CD receiver’s LINE 1 IN jacks to the TV’s audio output jacks.

Hint:

To listen to the TV, select the LINE 1 input source.

Connecting an Onkyo RI Dock (Remote Interactive Dock)

LINE 1

MD/

TAPE

OUT

DOCK/

CDR

CD receiver’s

rear panel

White

Red

White

Analog audio cable (RCA)

u cable supplied with

the Onkyo RI Dock

Onkyo RI Dock’s rear

panel

: Signal flow

Connecting a TV

LINE 1

MD/

TAPE

OUT

DOCK/

CDR

: Signal flow

CD receiver’s

rear panel

White

Red

White

Analog audio cable (RCA)

Connecting Other Components—Continued

The following diagram shows how to connect a portable audio device (e.g., MP3 player, MD player, CD player).

Connect the CD receiver’s LINE 2 IN jack on the front panel to the portable audio device’s output jack.

Depending on the type of output jack on the portable audio device, you may need to buy a suitable cable. The CD

receiver’s LINE 2 IN jack accepts a stereo miniplug.

Notes:

• Use a connecting cable that doesn’t have any attenuation resistors in it.

• If you connect a portable audio device’s headphone output to the CD receiver’s LINE 2 IN jack, turn down the volume

on the portable audio device before you connect it.

• When you connect a portable audio device to the CD receiver, make sure you connect it to the LINE 2 IN jack and

not the adjacent PHONES jack. If you connect to the PHONES jack by mistake, it may cause the PHONES output to

malfunction.

Connecting the Power Cord

Notes:

• Before connecting the power cord, connect all of your speakers and AV components.

• Turning on the CD receiver may cause a momentary power surge that might interfere with other electrical equipment

on the same circuit. If this is a problem, plug the CD receiver into a different branch circuit.

Plug the power cord into a suitable wall outlet.

The STANDBY indicator lights up.

Note:

To set the clock with the AccuClock function, the CD receiver must be able to receive RDS radio stations, which means

an FM antenna must be connected (see page 15).

Connecting a Portable Audio Device

: Signal flow

CD receiver’s front panel

Stereo miniplug cable

Portable audio device’s output jack

To wall outlet

Power cord

First Time Setup

RDS is only available in areas where RDS broadcasts are available.

To cancel this function while “Wait…” is displayed, press the INPUT button.

To use the AccuClock function, the CD receiver must be able to receive RDS radio stations, which means an FM antenna

must be connected. Be sure to connect an FM antenna before attempting to use this function (see page 15).

The very first time you turn on the CD receiver, the AccuClock function automatically sets the CD receiver’s clock based

on the CT (Clock Time) information present in an RDS radio broadcast. While the clock is being set, “Wait…” flashes

on the display, as shown. Note that it may take up to 5 minutes to set the clock.

When the clock has been set, the message “Clock Adjusted” scrolls across the display, then the day and time are dis-

played for a while, as shown.

The AccuClock function automatically updates the clock daily at 2 A.M., 3 A.M., and 2 P.M.

If for some reason the clock cannot be set automatically, see “Setting AccuClock to Use a Specific Station” on page 49

and “Setting the Clock Manually” on page 50.

Turning Off the AccuClock Function

If you don’t want AccuClock to automatically update the clock each day, you can turn it off as follows.

Note:

The AccuClock function cannot be turned off until the

clock has been set.

Setting the Clock with the AccuClock Function

YES/MODE

ENTER

TIMER

Press the [TIMER] button repeat-

edly until “Clock” appears on the

display.

Press [ENTER].

“*AccuClock*” appears on the display.

To turn off AccuClock, press the

[YES/MODE] button.

The asterisks disappear, indicating that

the AccuClock function is off. To turn

AccuClock back on again, press the

[YES/MODE] button so that the aster-

isks are displayed.

The asterisks indicate that the

AccuClock function is on.

Basic Operations

To turn on the CD receiver, press the [STANDBY/ON]

button on the CD receiver or remote controller. The

STANDBY indicator goes off.

Press the [STANDBY/ON] button again to set the CD

receiver to Standby. The STANDBY indicator lights up.

Tip:

When you start playback on (or turn on) an Onkyo RI

Dock, CD recorder, MD recorder, or cassette deck that’s

connected to the CD receiver with an

u cable and ana-

log audio cable, the CD receiver turns on automatically.

Similarly, when you set the CD receiver to On or

Standby, the other component will also be set to On or

Standby.

Turn the [VOLUME] control clockwise to increase the

volume or counterclockwise to decrease it.

You can also use remote controller’s VOLUME [q]/[w]

buttons.

You can select CD, DAB, FM, or a connected compo-

nent (TAPE, DOCK, LINE, DIGITAL) as the input

source.

To select the input source, press the remote controller’s

INPUT [t]/[1] buttons repeatedly. On the CD

receiver, press the [INPUT] button repeatedly. The input

sources are selected in the following order.

* Input Display can be changed (see page 28).

Turn down the volume, then connect your stereo head-

phones to the PHONES minijack.

You can adjust the volume and mute the sound, as

explained earlier.

The speakers output no sound while the headphones are

connected.

VOLUME

STANDBY/ON

INPUT

VOLUME

STANDBY/ON

INPUTPHONES

STANDBY indicator

Turning On the CD Receiver

Adjusting the Volume

Remote

controller

CD receiver

Remote

controller

CD receiver

Selecting the Input Source

Using Headphones

DIGITAL

DAB FM

LINE1LINE2

TAPE

DOCK

LINE1LINE2

TAPE

DOCK

• CR-725DAB

• CR-725

PHONES jack

Basic Operations—Continued

You can also use the [TONE] button and multi control on

the front panel to adjust the bass and treble.

To turn on the Super Bass function,

press the [S.BASS] button.

The S.BASS indicator lights up.

To turn off the Super Bass function, press the

[S.BASS] button again.

You can also use the [TONE] button on the

front panel. Press the [TONE] button for 3 seconds to

turn on the Super Bass function.

Note:

If you press the [

S.BASS] button while the Direct func-

tion is on, the Direct function will be turned off.

To turn the Direct function on or off, press

the [DIRECT] button on the CD receiver.

When the Direct function is off, the tone

controls can be used to adjust the sound.

When the Direct function is on, the tone

controls are bypassed, so you can enjoy a

pure sound, and the DIRECT indicator lights up.

On the remote controller, press the [TONE] button for 3

seconds to turn on the Direct function.

The [DIRECT] button’s indicator lights up, too.

To mute the output of the CD receiver, press the

remote controller’s [MUTING] button. The

MUTING indicator and the volume control

indicator flash on the display.

To unmute the CD receiver, press the [MUTING] button

again.

Tips:

While the CD receiver is muted:

• Turning the [VOLUME] control on the CD receiver or

pressing the VOLUME [

q]/[w] buttons on the remote

controller will unmute the CD receiver.

• If you turn the CD receiver off, the next time you turn

it on, the CD receiver will be unmuted.

MUTING

S.BASS

TONE

ENTER

DIRECT TONE

Adjusting the Bass and Treble

Remote

controller

Press the [TONE] button to select

“Bass”.

Use the Previous and Next

[7]/[6] buttons to adjust the

bass.

The default setting is “±0.” You can

adjust the bass and treble from –3 to +3.

Press [ENTER], and then use the

Previous and Next [7]/[6]

buttons to adjust the treble.

Notes:

• If you press no buttons for 8 seconds,

the previous display will appear auto-

matically.

• If you press the [TONE] button while

the Direct function is on, the Direct

function will be turned off.

Using the Super Bass Function

Remote

controller

Using the Direct Function

Muting the Sound

CD receiver

DIRECT indicator

Remote

controller

MUTING indicator

Basic Operations—Continued

You can choose what name is displayed when an input source is selected so that it matches the type of component that

you’ve connected to the MD/TAPE IN, DOCK/CDR IN, or OPTICAL DIGITAL IN (CR-725DAB only). When you

connect an Onkyo u-capable component, it’s important that you select the input source name that matches the type of

component for u to work properly.

You can also use the front panel controls.

1 Use the [INPUT] button to select the input source

whose name you want to change.

2 Push the multi control to select “Name Select?,” and

then push it again.

3 Turn the multi control to select the new input source

name.

4 Push the multi control to confirm your selection.

Input Source Name Abbreviations

Sometimes the input source name may be displayed as a

2-letter abbreviation, as per the following table.

Changing the Input Display

Use the INPUT [t]/[1] buttons

to select the input source whose

name you want to change.

CR-725DAB: TAPE, DOCK, DIGI-

TAL

CR-725: TAPE, DOCK

Press and hold the [MENU/NO]

button until “Name Select?”

appears on the display, and then

press [ENTER].

Use the Previous or Next

[7]/[6] button to select the

new input source name.

The input source names are selected in

the following orders:

MENU/NO

ENTER

INPUT

HOLD

MDTAPE VIDEO*

DAT*

DOCK CD-R

(CR-725DAB only)

* When you select an input source name,

you cannot select it as the recording com-

ponent at the set timer recording.

Press [ENTER] to confirm your

selection.

“Complete” appears on the display.

Full name Abbreviation

CDR CR

DAT DT

DIGITAL DG

GAME GM

DOCK DC

LINE LI

LINE1 L1

LINE2 L2

MD MD

PC PC

TAPE TP

VIDEO VD

DIGITAL CD-R/dig

GAME/dig PC/dig

Playing CDs

Selecting Tracks

To return to the beginning of the track

currently playing, turn the multi control

a little to the left.

Turn the multi control further to select

earlier tracks.

• While playback is stopped, turn the

multi control to the left to select the previous track.

Turn the multi control to the right to select subse-

quent tracks.

• On MP3 CDs, you can select MP3 files in other fold-

ers (see page 31).

Display

Disc tray

Press the Open/Close [0] button

to open the disc tray.

Tip:

Pressing the Open/Close [

0] button

while the CD receiver is on Standby will

turn on the CD receiver and open the disc

tray.

Place the CD on the tray with the

label-side facing up.

Place 8 cm CDs in the center of the tray.

To start playback, press the

Play/Pause [1/3] button.

The disc tray closes and playback starts.

To stop playback:

Press the Stop [2] button. Playback

stops automatically when the last track

has been played.

To pause playback:

Press the Play/Pause [1/3] button.

The Pause 3 indicator appears. To

resume playback, press the Play/Pause

[1/3] button again.

To remove the CD:

Press the Open/Close [0] button to open

the disc tray.

Tota l nu m b e r

of tracks

Total playing

time

“DISC TOTAL” lights up

while the disc informa-

tion is being displayed.

• Audio CD Display

Total number

of folders

Total number

of files

Disc name

• MP3 CD Display

CD receiver

Playing CDs—Continued

During playback or while playback is paused, press the remote controller’s [DISPLAY] button repeatedly to display the

following CD information.

Using the Remote Controller

To select:

Use the number buttons as

shown in the examples below to

select tracks.

Press to stop playback.

Press to pause playback.

To resume playback, press the Pause

[3] or Play [1] button.

Press:

Press to select tracks.

• Press the Previous [7] button to

locate the beginning of the currently

playing or paused track. Press it

repeatedly to select earlier tracks.

• Press the Next [6] button repeat-

edly to select subsequent tracks.

On MP3 CDs, you can select files in

other folders (see page 31).

Press to adjust the volume.

Press the VOLUME Up [q] button to turn

up the volume. Press the VOLUME

Down [w] button to turn it down.

Press to start playback.

Pressing this button while the CD

receiver is on Standby will turn on the

CD receiver and start playback.

Press to display more CD infor-

mation.

Tra ck # 8

Used to enter numbers over 10.

With MP3 CDs, you can select files in

the current folder with these buttons.

Track #10

Track #34

Press to fast forward or fast

reverse.

During playback or while playback is

paused, press and hold the Fast For-

ward [4] button to fast forward, or the

Reverse [5] button to fast reverse.

Displaying CD Information

The elapsed track time is displayed.

“REMAIN”

Lights up while the remaining track

time is being displayed.

“TOTAL REMAIN”

Lights up while the remaining disc

time is being displayed.

During random playback, or if the total

time is more than 99 minutes and 59

seconds, “– –:– –” is displayed.

Note:

See page 33 for details on dis-

playing MP3 information.

Playing CDs—Continued

On an MP3 CD, MP3 files may be organized in a hierar-

chically, with folders containing files and subfolders, as

shown below. On the CD receiver, there are two modes

for selecting MP3 files: Navigation mode and All Folder

mode. In Navigation mode, you can select MP3 files by

navigating through the folder hierarchy, moving in and

out of folders and subfolders. In All Folder mode, all

folders appear at the same level, making it easy to select

folders regardless of the hierarchy.

If you don’t select a specific MP3 file or folder for play-

back, all of the MP3 files on the CD will be played in

numerical order starting with file #1.

Selecting MP3 Files in Navigation Mode

With Navigation mode, you can select MP3 files by nav-

igating through the folder hierarchy. This mode can only

be used while playback is stopped.

If random mode or 1-folder mode is currently selected,

press the [YES/MODE] button to cancel it before pro-

ceeding.

You can also use the multi control for steps 2, 3, and 4.

Turn the multi control to select files and folders, and

push it for ENTER.

Selecting/Playing MP3 Files

File #1

File #10

Folder #3

Root Folder #1

Folder #2

File #13

Folder #4

File #14

File #18

File #11

File #12

FOLDER

MENU/NO

ENTER

While playback is stopped, press

the [FOLDER] button.

The CD receiver enters Navigation

mode and “Root” appears on the dis-

play.

Press [ENTER].

The name of the first folder one level

down from root appears on the display.

If the disc contains no folders, the name

of the first MP3 file is displayed.

Use the Previous and Next

[7]/[6] buttons to select

other folders and files at the

same level.

Folders that don’t contain MP3 files or

subfolders can’t be selected.

To access files or subfolders

inside another folder, select the

folder, and then press [ENTER].

Use the Previous and Next

[7]/[6] buttons to select the files

and subfolders within that folder.

To move up a level, press the

[MENU/NO] button.

To start playback, press the

[ENTER] or Play [1] button.

Playback will start with the specified

file or folder and continue until all of

the MP3 files on the disc have been

played.

Playing CDs—Continued

Selecting MP3 Files in All Folder Mode

With All Folder mode, you don’t have to navigate the

folder hierarchy because all folders that contain MP3

files appear at the same level.

If random playback is currently selected, press the

[YES/MODE] button to cancel it before proceeding.

You can also use the multi control for steps 2, 3, and 4.

Turn the multi control to select files and folders, and

push it for ENTER.

To select an MP3 file in another folder during playback,

press the [FOLDER] button, select the folder by using

the Previous and Next [7]/[6] buttons (or multi

control), and then press [ENTER] (or push the multi con-

trol). Now use the Previous and Next [7]/[6] but-

tons (or multi control) to select the MP3 files within that

folder.

■ Pausing Playback

To pause playback, press the Pause [3] button. To

resume playback, press it again.

■ Cancelling Navigation or All Folder Mode

To cancel Navigation mode or All Folder mode while

selecting MP3 files, press the Stop [2] button.

■ Selecting MP3 Folders and Files by Number

1 Press the [FOLDER] button for 2 seconds to enter

All Folder mode.

2 Use the number buttons as shown in the examples

below to enter folder numbers.

If playback is stopped, playback starts with the first

MP3 file in the specified folder. If playback is

already in progress, press [ENTER] to play the first

MP3 file in the specified folder.

3 Use the number buttons to enter the file number.

Playback starts.

If a folder contains more than 99 MP3 files, double-

digit file numbers must be preceded by zeros. For

example, to specify file #5, press [5]. To specify file

#32, press [>10], [0], [3], and [2].

HOLD

While playback is stopped, press

and hold the [FOLDER] button for

2 seconds.

The CD receiver enters All Folder

mode and the name of the first folder

appears on the display.

Use the Previous and Next

[7]/[6] buttons to select the

other folders.

You can select any folder that contains

MP3 files.

To play the first file in the selected

folder, go to Step 4.

To access the files inside the

folder, press the [FOLDER] but-

ton.

The name of the first MP3 file inside

the folder is displayed.

Use the Previous and Next

[7]/[6] buttons to select the

MP3 files within the folder.

To select another folder, press the

[FOLDER] button again, and then use

the Previous and Next [7]/[6]

buttons to select it.

FOLDER

ENTER

Number

buttons

To start playback, press the

[ENTER] or Play [1] button.

Playback will start with the specified

file or folder and continue until all of

the MP3 files on the disc have been

played.

To select: Press:

Folder #8

Used to enter numbers over 10.

Folder #10

Folder #34

Playing CDs—Continued

Playing the MP3 Files in Only One Folder

Normally, all of the MP3 files in all of the folders on the

disc are played. With 1-folder playback, only the MP3

files in the specified folder are played.

You can display various information about the MP3 file

currently playing, including ID3 tags such as title, artist

name, and album name.

Elapsed time:

The length of time that the current MP3 file has been

playing (default display). If the elapsed time is more than

99 minutes and 59 seconds, “– –:– –” is displayed.

File name:

Name of the current MP3 file.

Folder name:

Name of the current folder.

Title name:

Title of the current file (if ID3 tag present).

Artist name:

Name of the artist (if ID3 tag present).

Album name:

Name of the album (if ID3 tag present).

Sampling rate and bit rate:

Sampling rate and bit rate of the current MP3 file.

Notes:

• To display the disc name, press the [DISPLAY] button

while playback is stopped.

• If a file or folder name contains any characters that

cannot be displayed, an underscore will be displayed

in place of those characters. Alternatively, you can set

the CD receiver so that names containing such charac-

ters are displayed as “

File_n” or “Folder_n”,“n” being

the file or folder number (see page 36).

Press the [YES/MODE] button

repeatedly until the 1FOLDER

indicator appears.

Use the Previous and Next

[7]/[6] buttons to select the

folder.

You can select any folder that contains

MP3 files.

To start playback, press the

[ENTER] or Play [1] button.

Playback will start with the first MP3

file in the specified folder and continue

until all of the MP3 files in that folder

have been played.

Displaying MP3 Information

During playback, press the [DIS-

PLAY] button repeatedly to dis-

play the following MP3

information.

DISPLAY

YES/MODE

ENTER

1FOLDER indicator

Playing CDs—Continued

With memory playback, you can create a playlist of up

to 25 tracks.

Memory playback can be set only when the input source

is set to CD and playback is stopped.

Selecting Other Tracks During Memory Playback

To select other playlist tracks during memory playback,

use the remote controller’s Previous and Next

[7]/[6] buttons.

Checking What’s on the Playlist

To check what tracks are on the playlist, with playback

stopped, use the Fast Reverse and Fast Forward

[5]/[4] buttons to scroll through the playlist.

Removing Tracks from the Playlist

• While memory playback is stopped, press the

[CLEAR] button. Each press removes the last track

from the playlist.

• The playlist will be deleted when you cancel memory

playback, select random playback, press the

Open/Close [0] button to open the disc tray, or turn

off the CD receiver.

Cancelling Memory Playback

• To cancel Memory playback, press the [YES/MODE]

button repeatedly until the MEMORY indicator disap-

pears.

• Memory playback is cancelled when you press the

Open/Close [0] button to open the disc tray, or turn

off the CD receiver.

Memory Playback

Press the [YES/MODE] button

repeatedly until the MEMORY indi-

cator appears.

Use the Previous and Next

[7]/[6] buttons to select the

first track you want to add to the

playlist, and then press [ENTER].

Repeat this step to add additional tracks

to the playlist.

You can also use the number buttons on

the remote controller to select tracks.

On the front panel, you can also use the

multi control to add tracks to the playlist.

Turn the multi control to select a track,

and then push it for ENTER.

To select MP3 files for memory

playback:

In Navigation mode, use steps 1–4 on

page 31. In All Folder mode, use steps

1–4 on page 32.

YES/MODE

CLEAR

ENTER

Number buttons

(see page 30)

(These buttons do

nothing during

memory playback)

MEM

RY indicator

Playlist number

Track to be added

to the playlist

Total time of playlist

To remove tracks from the playlist:

Press the [CLEAR] button. Each press

removes the last track from the playlist.

Notes:

• If the total playing time is more than

99 minutes and 59 seconds, “– –:– –”

is displayed.

• You can add up to 25 tracks to the

playlist. If you try to add more, the

message “

Memory Full” appears.

To start memory playback, press

the Play [1] button.

On the CD receiver, press the Play/Pause

[1/3] button to start memory play-

back.

Track currently playing

Playing CDs—Continued

With random playback, all of the tracks on the disc are

played in random order.

Random playback can be set only when the input source

is set to CD and playback is stopped.

Cancelling Random Playback

• To cancel random playback, press the [SHUFFLE]

button repeatedly until the RANDOM indicator disap-

pears.

• Random playback is cancelled when you press the

Open/Close [0] button to open the disc tray, or turn

off the CD receiver.

With repeat playback, you can play an entire CD repeat-

edly, play one track repeatedly, or combine it with mem-

ory playback to play the playlist repeatedly, or random

playback to play all of the tracks on the disc in random

order repeatedly. With an MP3 CD, you can combine

repeat playback with 1-folder playback to play all of the

tracks in a specified folder repeatedly.

Repeat-1 playback can’t be combined with memory

playback, random playback, or 1-Folder playback.

Cancelling Repeat Playback

• To cancel repeat playback, press the [REPEAT] button

repeatedly until both the REPEAT and REPEAT 1

indicators disappear.

• Repeat playback is cancelled when you press the

Open/Close [0] button to open the disc tray, or turn

off the CD receiver.

Random Playback

Press the [SHUFFLE] button

repeatedly until the RANDOM indi-

cator appears.

To start random playback, press

the Play [1] button.

SHUFFLE

RANDOM indicator

Track currently playing

Repeat Playback

Press the [REPEAT] button repeat-

edly until the REPEAT or

REPEAT 1 indicator appears.

REPEAT

REPEAT or REPEAT 1 indicator

Playing CDs—Continued

With the MP3 preferences, you can change the way MP3

file information is displayed and the way MP3 CDs are

played.

The MP3 preferences can be set only when the input

source is set to CD and playback is stopped.

To cancel the procedure at any point, press the

[MENU/NO] button.

Preferences

Disc Name?

This preference determines whether or not the disc name

is displayed when an MP3 disc is loaded.

File Name?

This preference determines whether or not the file name

scrolls across the display when an MP3 file is selected.

In Navigation mode (see page 31), the file name scrolls

across the display regardless of this setting.

Folder Name?

This preference determines whether or not the folder

name scrolls across the display when an MP3 folder is

selected (in All Folder mode).

In Navigation mode (see page 31), the folder name

scrolls across the display regardless of this setting.

Bad Name?

This preference determines whether or not file and folder

names that contain undisplayable characters are replaced

with “File_n” or “Folder_n”, “n” being the file or folder

number. When set to “Not Replace”, displayable charac-

ters are displayed and underscore characters are used in

place of any undisplayable characters.

For ID3 tags, underscore characters are used in place of

undisplayable characters regardless of this preference.

ID3 Ver. 1?

This preference determines whether or not version

1.0/1.1 tags are read and displayed. When set to Not

Read, version 1.0/1.1 tags are not displayed.

ID3 Ver. 2?

This preference determines whether or not version

2.2/2.3/2.4 tags are read and displayed. When set to Not

Read, version 2.2/2.3/2.4 ID3 tags are not displayed.

Setting MP3 Preferences

Press the [MENU/NO] button

repeatedly until “Disc Name?”

appears.

Use the Previous and Next

[7]/[6] buttons to select the

preference you want to change.

The preferences are explained in the next

column.

Press [ENTER].

Use the Previous and Next

[7]/[6] buttons to select the

preference’s options.

Press [ENTER].

When the preference has been set, “Com-

plete” appears on the display.

MENU/NO

ENTER

Display (default)

Not Display

Scroll (default)

Not Scroll

Scroll (default)

Not Scroll

Replace

Not Replace (default)

Read (default)

Not Read

Read (default)

Not Read

Playing CDs—Continued

CD Extra?

This preference applies to CD Extra discs and deter-

mines whether music in the audio session or MP3 files in

the data session are played.

Joliet?

This preference applies to MP3 discs in Joliet format and

determines whether the CD receiver reads the SVD data

or treats the disc as an ISO 9660 disc. Normally, this

preference doesn’t need to be changed.

SVD (Supplementary Volume Descriptor) supports long

file and folder names and characters other than letters

and numbers. Some CD burning software refers to the

Joliet format as “Windows format”.

Hide Number?

This preference determines whether or not the numbers

at the beginning of file and folder names are hidden.

When you create an MP3 CD on a personal computer,

you cannot normally determine the playback order of the

files. However, if you number the MP3 files in order,

starting with 01, 02, 03, and so on, they will play in that

order. If you don’t want these numbers to appear on the

display, choose “Enable”.

The following table shows a few examples of numbered

file and folder names and how they will appear with the

“Disable” and “Enable” options.

Folder Key?

This preference determines how the [FOLDER] button

works.

Audio: Music in the audio session will be played

(default).

MP3: MP3 files will be played.

Use SVD: Reads in SVD data (default).

ISO9660: Will be read in as ISO9660 format.

Disable: The file and folder name, including

numbers, will be displayed as is

(default).

Enable: The file and folder name will be dis-

played but numbers will be hidden.

File/folder name

“Hide Number?” Option

Disable Enable

01 Pops 01 Pops Pops

10-Rock 10-Rock Rock

16_Jazz 16_Jazz Jazz

21th Century 21th Century 21th Century

05-07-20 Album 05-07-20 Album Album

All Folder: Pressing the [FOLDER] button once

selects All Folder mode.

Pressing and holding the [FOLDER]

button for 2 seconds selects Naviga-

tion mode.

Navigation (default):

Pressing the [FOLDER] button once

selects Navigation mode.

Pressing and holding the [FOLDER]

button for 2 seconds selects All

Folder mode.

Listening to the Radio

When tuned into a station, the Tuned indicator

appears. When tuned into a stereo FM station, the FM ST

indicator appears as well.

Tuning into weak stereo FM stations

If the signal from a stereo FM station is weak, it may be

impossible to get good reception. In this case, switch to

Manual Tuning mode and listen to the station in mono.

Adjusting the Antennas

Tuning into FM Radio Stations

YES/MODE

BAND

( TUN/

TUN )

AUTO

FM ST

Band Frequency

Press the [BAND] button repeat-

edly to select “FM”.

Press the [YES/MODE] button

repeatedly to select “Auto” or

“Manual”.

• Auto Tuning Mode

The AUTO indicator appears and ste-

reo radio reception is possible.

• Manual Tuning Mode

The AUTO indicator is not displayed

and radio reception will be in mono.

Use the Fast Reverse and Fast For-

ward [5]/[4] buttons to tune

into a station.

In Auto tuning mode, once a station is

found, tuning stops automatically.

The CD receiver changes FM frequency

in 0.05 MHz steps.

In Manual Tuning mode, the frequency

stops changing when you release the but-

ton. Press the button repeatedly to

change the frequency one step at a time.

AUTO indicator

Change the direction of the antenna to

achieve the best reception.

Affix the antenna with a thumbtack. (Do not

push the thumbtack through the antenna.)

Caution:

Be careful not to prick your finger!

Adjusting and installing the FM antenna

Choose a location for the FM antenna while listening to an FM station.

Listening to the Radio—Continued

Press the remote controller’s [DISPLAY] button repeatedly to display more radio information.

RDS is only available in areas where RDS broadcasts

are available.

What is RDS?

RDS stands for Radio Data System and is a method of

transmitting data in FM radio signals. It was developed

within the European Broadcasting Union (EBU) and

many European FM radio stations use it these days.

The CD receiver supports and displays the Program Ser-

vice Name (PS) and Radio Text (RT) types of RDS data.

The RDS indicator appears on the display when the CD

receiver is tuned to an FM station that supports RDS.

Notes:

• If the signal from an RDS station is weak, RDS data

may be displayed intermittently or not at all.

• The message “

Waiting…” may appear while the RT

data is being received.

*3 If the selected preset has no name, it will be skipped and the

next Program Service Name will be displayed.

Displaying Radio Information

DISPLAY

FM/DAB

Frequency

Preset name

*1 CR-725DAB only

*2 If the selected preset has no name, “No Name” appears

briefly and then the frequency is displayed. See “Naming

Presets” on page 46.

Receiving RDS

Frequency and preset number

Preset name

Program Service Name

Radio Text (if available)

Press the [DISPLAY] button repeatedly to dis-

play the following RDS information.

Listening to the Radio—Continued

Selecting DAB for the Very First Time

The very first time you select DAB, the Auto Tuning

function automatically scans the DAB Band III for the

multiplexes (i.e., stations) available in your area.

Once the scanning process is complete, the first station

that was detected is selected.

Using the Auto Tuning Function Manually

If a new DAB station is introduced, or you move to a new

area, you can run the Auto Tuning function again.

1 Press the [MENU/NO] button.

2 Use the Previous and Next [7]/[6] buttons to

select “Auto Tuning?” and then press [ENTER].

3 Use the Previous and Next [7]/[6] buttons to

select Worldwide or U.K., (see “Auto Tuning?” on

page 42), and then press [ENTER] to start the Auto

Tuning function.

The number of stations found and the scanning progress

are shown on the display.

To cancel Auto Tuning, press the [ENTER],

[MENU/NO] or [YES/MODE] button.

You can also use the front panel controls.

1 Push the multi control.

2 Turn the multi control to select “Auto Tuning?” and

then push it.

3 Turn the multi control to select Worldwide or U.K.,

and then push it to start the Auto Tuning function.

To cancel Auto Tuning, push the multi control.

Listening to DAB Digital Radio (CR-725DAB only)

Press the [BAND] button repeat-

edly to select “DAB”.

When tuned into a DAB station, the

Tuned indicator appears and the

DAB indicator as well.

On the front panel, press the [INPUT]

button repeatedly to select “DAB”.

BAND

MENU/NO

ENTER

Station name

Tuned indicator

DAB indicator

Listening to the Radio—Continued

Selecting DAB Stations

• You can also use the multi control to select DAB sta-

tions.

• Once a DAB station has been preset, these front panel

controls will select presets, in Preset mode. To use

them to select DAB stations, select DAB as the input

source, and then press the Stop [

] button for 3 sec-

onds until “Station Mode” appears on the display.

Displaying DAB Radio Information

Press the remote controller’s [DISPLAY] button repeat-

edly to display more information about the selected

DAB station.

You can also use the CD receiver’s [DISPLAY] button to

display this information.

1. DLS (Dynamic Label Segment)

When tuned to a station that’s broadcasting DLS text

data, the text will scroll across the display.

2. Program Type

Displays the type of program.

3. Bit Rate and Audio Mode

Displays the station’s bit rate and audio mode (ste-

reo, mono, or joint stereo).

4. Signal Quality

Displays the signal quality.

0–59: Poor reception

60–79: Good reception

80–100: Excellent reception

5. Multiplex Name

Displays the name of the current multiplex.

6. Multiplex Number and Frequency

Displays the number and frequency of the current

multiplex.

Use the Fast Reverse and Fast

Forward [5]/[4] buttons to

select the DAB stations.

If a secondary service is available, a

right angle bracket (>) is displayed.

Press the Fast Forward [4] button to

listen to the secondary service.

While the secondary service is selected,

a left angle bracket (<) is displayed.

Press the Fast Reverse [5] button to

return to the primary service.

When you select a station that you’ve

selected a lot in the past, the letter F

(short for Favorite) is displayed.

If you select a station that cannot be

received properly, a question mark (?)

is displayed.

DISPLAY

( TUN/

TUN )

“F”

“?”

(Scroll)

Listening to the Radio—Continued

DAB Setup

Use the following functions and settings to set up DAB

digital radio.

■ Preset Write?

Select this to preset the current DAB station. See “Pre-

setting FM/DAB Stations Manually” on page 44 for

more information.

■ Tuning Mode?

With this setting, you can sort the available stations

alphabetically, by multiplex, favorites, or active stations.

Use the Previous and Next [7]/[6] buttons to

select the following options, and then press [ENTER].

■ Trim Station?

With this function, you can delete all of the stations that

cannot be received properly.

■ Auto Tuning?

This setting determines which DAB bands are scanned

by the Auto Tuning function (see page 40).

■ DRC Setting?

With the DRC (Dynamic Range Control) setting, you

can reduce the dynamic range of DAB digital radio so

that you can still hear quiet parts even when listening at

low volume levels—ideal for listening to the radio late at

night when you don’t want to disturb anyone.

Use the Previous and Next [7]/[6] buttons to

select the following options, and then press [ENTER].

■ Tuning Aid?

With the Tuning Aid, you can adjust the position and

direction of the DAB antenna while monitoring the sig-

nal strength on the display. If the letter “B” appears on

the display, it means the signal strength is Bad. If the

letter “G” appears, it means the signal strength is Good.

To make the letter “G” appear, adjust the antenna to get

the best signal strength.

Use the Previous and Next [7]/[6] buttons to

select other multiplexes (Band III: 5A–13F or L-Band:

LA–LW).

Press the [MENU/NO] button.

Use the Previous and Next

[7]/[6] buttons to select the

item you want to set, and then

press [ENTER].

The items are explained below.

Alphabet (default):

Sort stations alphabetically.

Multiplex: Sort stations by multiplex.

Favorite: Sort stations by favorites. The stations

you select the most will appear at the

top of the list.

MENU/NO

Active St: Sort by active stations. Receivable sta-

tions appear at the top of the list. sta-

tions that cannot be received properly

appear at the bottom of the list.

UK: Band III (11B–12D).

Worldwide (default):

Band III (5A–13F) and L-Band (LA–LW).

0 (default): DRC off.

1: Large reduction in dynamic range.

1/2: Small reduction in dynamic range.

Multiplex Number

G (Good) or B (Bad)

Listening to the Radio—Continued

With the Auto Preset function, you can automatically preset all of the FM radio stations available in your area in one

go. Presets make it easy to select your favorite stations and eliminate the need to tune the radio manually each time you

want to change stations.

Note:

Depending on your location, a preset may be stored with

no station and you will hear only noise when you select

it. In this case, delete the preset (see page 48).

You can also use the front panel controls.

1 Press the [INPUT] button repeatedly until “FM”

appears.

2 Push the multi control, and then turn it to select

“AutoPreset?”

3 Push the multi control. The confirmation message

“AutoPreset??” appears.

4 To start the Auto Preset function, push the multi con-

trol.

After Storing Presets You Can:

• Select them (see page 45)

• Name them for easy identification (see page 46)

• Copy them (see page 47)

• Erase them (see page 48)

Presetting FM Stations Automatically (Auto Preset)

BAND

MENU/NO

ENTER

INPUT

Any existing presets will be deleted when the

Auto Preset function is run.

Auto Preset Caution!

Press the [BAND] or INPUT

[t]/[1] buttons repeatedly until

“FM” appears.

Make sure the FM antenna is positioned

to achieve the best possible reception.

Press the [MENU/NO] button, and

then use the Previous and Next

[7]/[6] buttons to select

“AutoPreset?”.

Press [ENTER].

The confirmation message “AutoPre-

set??” appears.

To cancel the Auto Preset function at this

point, press the [MENU/NO] button.

To start the Auto Preset function,

press [ENTER].

Up to 20 stations can be preset and pre-

sets are stored in frequency order.

Listening to the Radio—Continued

With the Preset Write function, you can manually preset individual FM, and DAB radio stations. Presets make it easy

to select your favorite stations and eliminate the need to tune the radio manually each time you want to change stations.

FM stations can also be preset automatically (see page 43).

You can also use the front panel controls.

1 Tune into the station you want to store as a preset

(see page 38).

2 Push the multi control, and then turn it to select “Pre-

set Write?”.

3 Push the multi control.

4 Turn the multi control to select a preset.

5 To store the station, push the multi control.

Note:

If the current FM station supports RDS and PS (Program

Service Name), the station’s name will be displayed

instead of the frequency. (See page 39 for more on

RDS.)

After Storing Presets You Can:

• Select them (see page 45)

• Name them for easy identification (see page 46)

• Copy them (see page 47)

• Erase them (see page 48)

Presetting FM/DAB Stations Manually

MENU/NO

ENTER

• You can store up to 40 FM and DAB stations as presets and

this can be any combination. For example, 27 FM and 13

DAB or 18 FM and 22 DAB.

• Although FM and DAB presets share the same numbers,

they’re selected independently. For example, preset #1 will

store DAB station when the DAB band is selected, and an FM

station when the FM band is selected.

• Stations can be stored to presets in any order. For example,

you could store preset #5 first, #1 second, and so on.

About Presets

Tune into the station that you want

to store as a preset.

Press the [MENU/NO] button, and

then use the Previous and Next

[7]/[6] buttons to select “Pre-

set Write?”.

Press [ENTER].

The preset number flashes.

To cancel the Preset Write function at

this point, press the [MENU/NO] button.

Use the Previous and Next [7]

/[6] buttons to select a preset.

To store the station, press

[ENTER].

If no station has yet been stored to the

selected preset, “Complete” appears and

the station is stored.

If a station has already been stored in the

selected preset, the message “Over-

write?” appears.

To overwrite the previously stored sta-

tion, press the [YES/MODE] button.

To not overwrite the previously stored

station, press the [MENU/NO] button.

If the message “Memory Full” appears,

all 40 presets have been stored and you’ll

need to erase some presets before you can

store any more stations (see page 48).

Repeat steps 1 to 5 to preset more radio

stations.

Listening to the Radio—Continued

You must store some presets before you can select them

(see pages 43 and 44).

You can also use the front panel controls.

1 Use the [INPUT] button to select “FM”, or “DAB”.

2 To select DAB stations, press the Stop [

] button for

3 seconds until “Preset Mode” appears on the dis-

play.

3 Turn the multi control to select a preset.

Selecting Preset Stations

Use the [BAND] or INPUT

[t]/[1] buttons to select “FM”

or “DAB”.

The preset you selected the last time you

listened to the radio will still be selected.

Use the Previous and Next

[7]/[6] buttons to select a

preset.

Press the Previous [7] button to select

the previous preset. Press the Next

[6] button to select the next preset.

INPUT

BAND

( PRESET/

PRESET )

Number

buttons

You can also use the number but-

tons as shown in the examples

below to select presets.

To select:

Press:

Preset #8

Used to enter numbers over 10.

Preset #10

Preset #22

Listening to the Radio—Continued

You can name presets for easy identification. The preset

name may contain of up to eight characters.

You can also use the front panel controls.

1 Select the preset you want to name (see page 45).

2 Push the multi control, and then turn it to select

“Name In?”

3 Push the multi control.

4 Turn the multi control to select a character, and then

push it.

5 Repeat step 4 to enter up to 8 characters.

Use the remote controller’s [DISPLAY] button to select

the character groups.

Available Characters

Naming Presets

Select the preset you want to

name (see page 45).

Press the [MENU/NO] button, and

then use the Previous and Next

[7]/[6] buttons to select

“Name In?”.

Press [ENTER].

Press the [DISPLAY] button

repeatedly to select one of the fol-

lowing character groups:

• “A” for uppercase letters.

• “a” for lowercase letters.

• “1” for numbers and symbols.

• Selecting letters:

Press the number buttons repeatedly

to select the available letters. For

example, press the [2] button repeat-

edly to select: A, B, or C.

• Selecting numbers and symbols:

Use the number buttons to select

numbers.

Press the [>10] button repeatedly to

select: (space) . / * - , ! ? & ’ ( )

Press the [0] button repeatedly to

select: 0 or (space)

ENTER

YES/MODE

DISPLAY

MENU/NO/

CLEAR

Number

buttons

Character group

Note:

Not all of the symbols can be entered by

using the number buttons. Use the Previ-

ous and Next [

7] or [6] buttons to

select from the full range of symbols.

When you’ve selected the charac-

ter you want, press [ENTER], and

then choose the next character.

• Editing characters:

To change or delete a character

you’ve already entered, use the Fast

Reverse and Fast Forward

[5]/[4] buttons to select it, and

then select another character, or press

the [CLEAR] button to delete it.

• Inserting a new character:

To insert a new character, use the Fast

Reverse and Fast Forward

[5]/[4] buttons to select the

character immediately after the inser-

tion point. That character flashes.

Use the Previous and Next [

7] or

[

6] buttons to select “ ”, press

[ENTER], and then select the new

character.

To cancel the Name In function, press

and hold the [MENU/NO] button for 2

seconds.

When you’ve finished entering the

name, press the [YES/MODE] but-

ton.

The preset is named and “Complete”

appears on the display.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

a b c d e f g h i j k l m n o p q r s t u v w x y z

0 1 2 3 4 5 6 7 8 9

_@'<>#$%&* =;:+-/()?

! ’ ” , . (space) (insert)

Listening to the Radio—Continued

With the Preset Copy function, you can organize your

presets in the order you want. When you copy a preset,

its name is also copied.

You can also use the front panel controls.

1 Select the preset you want to copy (see page 45).

2 Push the multi control, and then turn it to select “Pre-

setCopy?”.

3 Push the multi control.

4 Turn the multi control to select the destination pre-

set.

5 To copy the preset, push the multi control.

Tip:

If you favorite station is stored in preset #5 and you want

to make it preset #1, copy preset #5 to preset #1. To keep

the station that’s already stored in preset #1, you may

want to copy it to an unused preset first.

Copying Presets

Select the preset you want to copy

(see page 45).

Press the [MENU/NO] button, and

then use the Previous and Next

[7]/[6] buttons to select “Pre-

setCopy?”.

Press [ENTER].

The number of the preset to be copied

flashes.

Use the Previous and Next

[7]/[6] buttons to select the

destination preset.

The number of the destination preset

flashes.

MENU/NO

ENTER

To copy the preset, press

[ENTER].

If no station has yet been stored in the

destination preset, the station is copied

and “Complete” appears.

If a station has already been stored in the

destination preset, the message “Over-

write?” appears.

To overwrite the previously stored sta-

tion, press [ENTER].

To not overwrite the previously stored

station, press the [MENU/NO] button.

Listening to the Radio—Continued

You can also use the front panel controls.

1 Select the preset whose name you want to erase (see

page 45).

2 Push the multi control, and then turn it to select

“NameErase?”.

3 To erase the preset’s name, push the multi control.

You can also use the front panel controls.

1 Select the preset you want to erase (see page 45).

2 Push the multi control, and then turn the multi con-

trol to select “PresetErase?”.

3 Push the multi control. The confirmation message

“Erase OK?” appears.

4 To erase the preset, push the multi control.

Erasing a Preset’s Name

Select the preset whose name you

want to erase (see page 45).

Press the [MENU/NO] button, and

then use the Previous and Next

[7]/[6] buttons to select

“NameErase?”.

To erase the preset’s name, press

the [YES/MODE] button.

The preset’s name is erased and “Com-

plete” appears on the display.

MENU/NO

YES/MODE

Erasing Presets

Select the preset you want to

erase (see page 45).

Press the [MENU/NO] button, and

then use the Previous and Next

[7]/[6] buttons to select

“PresetErase?”.

Press [ENTER].

A message requesting confirmation

appears.

To cancel the Preset Erase function at

this point, press the [MENU/NO] button.

To erase the preset, press

[ENTER].

The preset is erased and “Complete”

appears on the display.

MENU/NO

ENTER

Setting the Clock

RDS is only available in areas where RDS broadcasts are available.

The AccuClock function normally uses the FM station with the strongest signal to set the clock. However, if the clock

cannot be set properly using that station, you can specify which FM station the AccuClock function should use. This

must be an FM station that supports RDS CT (Clock Time) information.

Setting AccuClock to Use a Specific Station

Remote

controller

Press the [TIMER] button.

“Clock” appears on the display.

If the clock has already been set, a timer

option appears instead, in which case

you’ll need to press the [TIMER] button

repeatedly until “Clock” appears.

Press [ENTER].

“AccuClock”or “*AccuClock*” appears

on the display.

If “ManualAdjust” appears, use the Pre-

vious and Next [7]/[6] buttons to

select “AccuClock” or “*AccuClock*”.

Press [ENTER].

The frequency flashes on the display.

Use the Fast Reverse and Fast For-

ward [5]/[4] buttons to tune

into the FM station.

Tip:

If you press the [YES/MODE] button

instead of using the Fast Reverse and

Fast Forward [

5]/[4] buttons, the

CD receiver will automatically search for

a suitable station.

The RDS indicator appears when tuned

into a station that supports RDS.

The RDS indicator will flash while the

CD receiver searches for a station and

light up continuously when a station is

found.

When you’ve selected the station,

press [ENTER].

While the clock is being set, “Wait”

flashes on the display. It may take a few

minutes to set the clock. When the clock

has been set, the message “Clock

Adjusted” scrolls across the display, then

the day and time are displayed for a

while.

Notes:

• If the clock is not set correctly, specify

another FM station and try again or set

the clock manually (see page 50).

• The AccuClock function automati-

cally updates the clock every day. If

you don’t want it to, you can turn off

the AccuClock function (see page 25).

Setting the Clock—Continued

The time can be displayed in either 12- or 24-hour for-

mat.

Displaying the Day and Time

To display the day and time, press the remote controller’s

[CLOCK CALL] button.

If the CD receiver is on Standby, the time is displayed for

8 seconds.

Using the 12- or 24-hour Format

To change the time format between 12-hour and 24-hour,

while the time is shown on the display, press the [DIS-

PLAY] button.

Displaying the Time in Standby Mode

To set the CD receiver so that the time is displayed while

its on Standby, turn on the CD receiver, and then press

and hold its [STANDBY/ON] button for 2 seconds.

Note that having the time displayed in Standby mode

will consume a little more power.

Setting the Clock Manually

Press the [TIMER] button repeat-

edly until “Clock” appears.

Press [ENTER].

Use the Previous and Next [7]/

[6] buttons to select “Manual-

Adjust”.

Press [ENTER].

Use the Previous and Next [7]/

[6] buttons to select the day of

the week.

You can select: SUN, MON, TUE, WED,

THU, FRI, or SAT.

Press [ENTER].

To cancel the Manual Adjust function at

this point, press the [MENU/NO] button.

TIMER

STANDBY/ON

ENTER

DISPLAY

MENU/NO

CLOCK

CALL

Number

buttons

Use the Previous and Next [7]/

[6] buttons to set the time.

You can also use the remote controller’s

number buttons to enter the time.

For the 12-hour format, use the remote

controller’s [>10] button to select AM or

PM.

Press [ENTER].

The clock is set and the second dot starts

flashing.

Using the Timers

The CD receiver has five timers: four programmable tim-

ers for automated playback or recording, and a sleep timer

for turning the CD receiver off after a specified period.

The timers can be used with other Onkyo components

that are connected to the CD receiver via u (see pages

19 to 23 for hookup details).

The various settings for the four programmable timers

are explained here. For details on the sleep timer, see

page 55.

Timer Types

Each timer can be programmed for playback (Play) or

recording (Rec).

■ Play

Play mode can be used to start playback at a specified

time on the CD receiver or another Onkyo component

that’s connected to the CD receiver with an u cable.

You could use a Play timer to turn on the CD receiver

every morning, just like a radio alarm.

■ Rec

Rec mode can be used to start playback on one compo-

nent and start recording on another component at a spec-

ified time. The recording component (e.g., Onkyo

cassette deck or MD recorder) must be connected to the

CD receiver with an u cable. You could use a Rec

timer to record your favorite radio show every day.

Playback and Recording Components

The playback component can be the CD receiver (FM,

DAB or CD), an Onkyo component (MD recorder, cas-

sette deck, etc) that’s connected to the CD receiver with

an u cable, or a component that’s connected to one of

the CD receiver’s inputs, perhaps one with its own built-

in timer.

The recording component can be an Onkyo MD recorder

or cassette deck that’s connected to the CD receiver with

an u cable.

Repeat Timers

Each timer can be programmed to work just once

(Once), every week (Every), every day (Every Day), or

on a range of days (Days Set).

■ Once

The timer will work just once.

■ Every

The timer will work every week on the specified day and

time.

•Everyday

The timer will work every day.

• Days Set

The timer will work on the specified range of days. With

this setting, you could set up a morning alarm for Mon-

day to Friday.

Timer Examples

The following examples highlight some of the ways in

which you can use the timers.

Timer Priority

If two or more timers are set to the same On time, the

lowest numbered timer has priority. For example:

If two or more timers overlap, the timer with the earliest

start time has priority. For example:

If the On and Off times of two timers are the same, the

timer with the earliest start time has priority and the

other timer will fail. For example:

Timer Indicators

When a timer has been set, the TIMER indica-

tor and the number of the timer appear on the

display. If the timer has been set to perform

recording, an underscore character appears

underneath the timer’s number.

Notes:

• The timers work only if the CD receiver is on Standby.

If it’s on when a timer is supposed to start playback or

recording, nothing will happen.

• While timed playback or recording is in progress, the

timer’s Off time cannot be changed.

• To use timed playback or recording with an external

component, make sure it’s properly connected to the

CD receiver. Also, for u to work properly, make

sure that the Input Display on the CD receiver is set to

match the type of component you’ve connected to the

MD/TAPE IN, DOCK/CDR IN, or OPTICAL DIGI-

TAL IN (CR-725DAB only) (see page 28).

About the Timers

Timer 1: To wake up to your favorite radio station

(preset #1) every morning, set as follows:

Play

➔FM 1➔Every➔Every Day➔On

7:00

➔Off 7:30

If you want a radio alarm only on weekdays,

select “Days Set” instead of “Every Day”

and specify “MON–FRI.”

Timer 2: To record a one-off radio show (preset #2) to

a cassette deck this Sunday, set as follows:

Rec

➔FM 2➔TAPE➔Once➔SUN➔On

21:00

➔Off 22:00

(You need an u-capable Onkyo cassette

recorder or MD recorder to do the record-

ing.)

Timer 3: To record an FM radio show to a MiniDisc

recorder every day from Monday to Friday,

set as follows:

Rec

➔FM 1➔MD➔Every➔Days

Set

➔MON➔ FRI➔On 15:00➔Off 15:30

Timer 1: 07:00 – 13:00 (This timer has priority.)

Timer 2: 07:00 – 12:30

Timer 1: 9:00 – 10:00

Timer 2: 8:00 – 10:00 (This timer has priority.)

Timer 1: 0:00 – 1:00 (This timer has priority.)

Timer 2: 1:00 – 2:00

Using the Timers—Continued

Notes:

• You must set the clock before you can program the

timers.

• Before programming a timer to turn on the radio, you

must preset the station you want to use. (See pages 43

and 44.)

• If you don’t operate any buttons for 60 seconds while

programming a timer, the procedure will be cancelled

and the previous display will reappear.

Programming the Timers

Press the [TIMER] button repeat-

edly to select Timer 1, 2, 3, or 4,

and then press [ENTER].

If “Clock” appears, you need to set the

clock (see pages 25, 49, and 50).

Use the Previous and Next [7]/

[6] buttons to select “Play” or

“Rec”, and then press [ENTER].

If you can’t select “Rec”, make sure that

your Onkyo cassette deck or MD

recorder is properly connected to the

MD/TAPE jacks (pages 19 and 20) and

the Input Display is set accordingly

(page 28).

TIMER

STANDBY/ON

ENTER

Number buttons

Use the Previous and Next [7]/

[6] buttons to select the source,

and then press [ENTER].

You can select the following sources:

CR-725DAB

FM, TAPE, DOCK, LINE1, LINE2,

DIGITAL, CD, or DAB.

CR-725

FM, TAPE, DOCK, LINE1, LINE2, or

CD.

If you selected Rec, CD cannot be

selected as the source.

If you selected “FM” or “DAB”, use

the Previous and Next [7]/[6]

buttons to select the radio preset,

and then press [ENTER].

If you selected “Rec”, make sure

the name of the connected

recorder is flashing on the display,

and then press [ENTER].

Use the Previous and Next [7]/

[6] buttons to select “Once” or

“Every”, and then press [ENTER].

Select “Once” for on-off operation.

Select “Every” to perform the same oper-

ation every week.

Using the Timers—Continued

To return to step 1 and start timer programming all over

again, press the [MENU/NO] button at any point in this

procedure.

If you selected “Once”, use the

Previous and Next [7]/[6]

buttons to select the day, and then

press [ENTER].

You can select: SUN, MON, TUE, WED,

THU, FRI, or SAT.

Go to step 10.

If you selected “Every”, use the

Previous and Next [7]/[6]

buttons to select the day, “Every-

day” or “Days Set”, and then press

[ENTER].

You can select the following:

If you selected “Days Set”, use the

Previous and Next [7]/[6]

buttons to select the first day, and

then press [ENTER].

Use the Previous and Next [7]/

[6] buttons again to select the

last day, and then press [ENTER].

You can select only consecutive days.

Use the Previous and Next [7]/

[6] buttons to specify the On

time, and then press [ENTER].

You can also use the remote controller’s

number buttons to enter the time. For

example, to enter 7:29, press [7], [2], and

[9].

Notes:

• Once the On time is set, the Off time is

automatically set to one hour later.

• To ensure that the first few seconds of

a program are recorded when using

timer recording, set the On time

slightly ahead of the program’s start

time (about 1 minute).

SUN

TUE

MON

Days Set Everyday

WED THU

SAT

FRI

Use the Previous and Next [7]/

[6] buttons to specify the Off

time, and then press [ENTER].

If you selected “Play” in step 2,

Use the Previous and Next [7]/

[6] buttons to specify the CD

receiver’s volume level, and then

press [ENTER].

The default setting is “10”.

If you want to use your normal volume

level setting for the timer, press the Pre-

vious [7] button repeatedly until

“TimerVol.Off” appears on the display.

In this case, the timer will use the volume

level that was set before the CD receiver

was set to Standby.

TIMER indicator 1, 2, 3, or 4 will

stop flashing and light up.

Press the [STANDBY/ON] button

to set the CD receiver to Standby.

Notes:

• Be sure to set the CD receiver to

Standby, otherwise the timed opera-

tion will not work.

• While a timed operation is in progress,

you can cancel it by pressing the

[TIMER] or [SLEEP] button.

• While timed recording is in progress,

the output of the CD receiver is muted.

To hear what’s being recorded, press

the [MUTING] button. Press it again

to mute the CD receiver.

• Memory, random, and 1-Folder play-

back cannot be used with the timers.

Remote

controller

CD receiver

TIMER indicator

Number of

programmed

timer

Underscore indicates

timer programmed for

recording

Using the Timers—Continued

Once a timer has been programmed, you can turn it on or

off as necessary. For example, while you’re on holiday,

you may want to turn off the timer you use as an early-

morning alarm.

Turning Timers On and Off

Press the [TIMER] button repeat-

edly to select Timer 1, 2, 3, or 4.

When a timer has been programmed, its

number appears on the display.

Use the Previous and Next [7]/

[6] buttons to select “Timer On”

or “Timer Off”.

After a few moments, the previous dis-

play reappears.

TIMER

ENTER

MENU/NO

Checking Timer Settings

Press the [TIMER] button repeat-

edly to select Timer 1, 2, 3, or 4,

and then press [ENTER].

Press [ENTER] repeatedly to see

all of the timer’s settings.

Notes:

• You can change the settings by using

the Previous and Next [7]/[6]

buttons.

• If you change the settings of a timer

that is off, that timer will be turned on.

If you don’t change any settings, the pre-

vious display reappears.

To return to the previous display at any

point in this procedure, press the

[MENU/NO] button.

Using the Timers—Continued

With the sleep timer, you can set the CD receiver so that

it automatically turns off after a specified period.

Checking the Remaining Sleep Time

To check the remaining sleep time, press the [SLEEP]

button.

Note that if you press the [SLEEP] button while the sleep

time is being displayed, you’ll shorten the sleep time by

10 minutes.

Canceling the Sleep Timer

To cancel the sleep timer, press the [SLEEP] button

repeatedly until the SLEEP indicator disappears.

Using the Sleep Timer

Press the [SLEEP] button repeat-

edly to select the required sleep

time.

With the [SLEEP] button, you can set the

sleep time from 90 to 10 minutes in 10

minute increments.

Use the Previous and Next [7]/[6]

buttons to set the sleep time in 1 minute

increments from 99 to 1.

When the sleep timer has been set, the

SLEEP indicator appears on the display,

as shown. The sleep time appears on the

display for about 8 seconds, then the pre-

vious display reappears.

Note:

The sleep timer will be ignored while

dubbing a CD to an Onkyo cassette deck

or MD recorder is in progress. The CD

receiver will automatically switch to

Standby when the dubbing is complete.

SLEEP

SLEEP indicator

Troubleshooting

If you have any trouble using the CD receiver, look for a solution in this section.

Can’t turn on the CD receiver.

• Make sure that the power cord is properly plugged into the wall outlet (see page 24).

• Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.

The CD receiver turns off unexpectedly.

• If the sleep timer has been set and the TIMER indicator is shown on the display, the CD receiver will turn off auto-

matically after a specified period.

• When timed playback or recording finishes, the CD receiver automatically switches to Standby mode.

• If the STANDBY indicator is flashing, the built-in amplifier protection circuit has been activated. This can happen if

there’s a short between the positive and negative wires of a speaker cable.

There’s no sound.

• Make sure the CD receiver’s volume control is not set to minimum (see page 26).

• Make sure the correct input source is selected (see page 26).

• Make sure the CD receiver is not muted (see page 27).

• Make sure the speakers are connected correctly (see page 17).

• Check all connections and correct as necessary (see pages 15 to 24).

• While headphones are connected, the speakers output no sound (see page 26).

The sound quality is not good.

• Make sure the speaker cables are connected with the correct polarity (see page 17).

• Make sure all audio connecting plugs are pushed in all the way (see page 18).

• The sound quality can be affected by strong magnetic fields, such as that from a TV. Try moving any such devices

away from the CD receiver.

• If you have any devices that emit high-intensity radio waves near the CD receiver, such as a cellular phone that’s being

used to make a call, the CD receiver may output noise.

• The CD receiver’s precision drive mechanism may emit a faint hissing sound while reading discs during playback or

when searching for tracks. You may be able to hear this noise in extremely quiet environments.

Audio output is intermittent when the CD receiver is subjected to vibration.

• The CD receiver is not a portable device. Use it in a location that’s not subject to shock or vibration.

Headphone output is intermittent or there’s no sound.

• This may be due to dirty contacts. Clean the headphones plug. See your headphones’ instruction manual for cleaning

information. Also, make sure that the headphones cable is not broken or damaged.

If you can’t resolve the issue yourself, try resetting the CD receiver before contacting your Onkyo dealer.

Note that resetting the CD receiver will delete your radio presets and custom settings.

To reset the CD receiver to its factory defaults, turn it

on and, while holding down the [2] button, press the

[STANDBY/ON] button.

“Clear” will appear on the display and the CD receiver

will enter Standby mode.

STANDBY/ON

HOLD

Power

Audio

Troubleshooting—Continued

Audio performance

• Audio performance will be at its best about 10 to 30 minutes after the CD receiver has been turned on and had time

to warm up.

• Using cable ties to bundle audio cables with speaker or power cables may degrade the sound quality, so don’t do it.

Playback jumps.

• The CD receiver is being subjected to vibration or the disc is scratched or dirty (see page 14).

Can’t add tracks to the playlist for memory playback.

• Make sure there’s a disc in the CD receiver. Also, you can only add valid track numbers. For example, if the CD

contains 11 tracks, you cannot add track #12.

The disc will not play.

• Make sure the disc has been loaded correctly, with the label-side facing up.

• Check to see if the surface of the disc is dirty (see page 14).

• If condensation is suspected, turn on the CD receiver and leave it for 1 hour before playing any discs.

• Some CD-R/RW discs may not be playable (see page 13).

It takes a long time for playback to start.

• It may take the CD receiver a while to read CDs that contain many tracks or files.

Can’t play MP3 discs.

• Use only ISO 9660 Level 1 or Level 2 format discs (see page 13).

• The disc has not been finalized. Finalize the disc.

• MP3 files without a “.mp3” or “.MP3” filename extension are not recognized.

Reception is noisy, stereo FM reception suffers from hiss, the Auto Preset function doesn’t preset all stations, or

the ST indicator doesn’t light up when tuned to a stereo FM station.

• Check the antenna connections (see page 15).

• Change the position of the antenna (see page 38).

• Move the CD receiver away from a nearby TV or computer.

• Cars or airplanes can cause noisy interference.

• The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna.

• Try setting FM mode to mono (see page 38).

• Move power cords and speaker cables as far away as possible from the tuner’s antenna.

• If none of the above improves the reception, install an outdoor antenna (see page 16).

If a power outage occurs or the power cable is disconnected:

• If the preset stations are lost, preset them again (see pages 43, 44).

• The clock and timer settings will be lost. Set the clock and timers again (see pages 49, 50).

Can’t adjust the frequency of the radio.

• Use the Fast Reverse and Fast Forward [5]/[4] buttons to change the frequency of the radio (see page 38).

RDS doesn’t work.

• The FM station you are tuned to doesn’t support RDS.

• Install an outdoor FM antenna (see page 16).

• Change the position or direction of your outdoor FM antenna (see pages 16, 38).

• Move the FM antenna as far away as possible from fluorescent lights (see page 38).

CD Playback

Tuner

Troubleshooting—Continued

The remote controller doesn’t work properly.

• Make sure the batteries have been installed with the correct polarity (+/–) (see page 5).

• Replace both batteries with new ones. (Do not mix different types of batteries or new and old batteries.)

• The remote controller is too far away from the CD receiver, or there’s an obstacle between them (see page 11).

• The CD receiver’s remote control sensor is being subjected to bright light (inverter-type fluorescent light or sunlight).

• The CD receiver is located behind the glass doors of a audio rack or cabinet.

Interactive control with other Onkyo u-capable components is not working.

• Make sure the u cables and analog audio cables are connected correctly (see pages 19 to 23). Connecting only an

u cable won’t work.

• Make sure the Input Display matches the type of device that you’ve connected to the CD receiver (see page 28).

• When recording an MP3 CD to an Onkyo recording component, recording will start without performing a peak search

when the [CD DUBBING] button is pressed on the recording component. This is not a malfunction.

No sound is heard from a connected component.

• Make sure the optical digital audio cable is not bent or damaged. (CR-725DAB)

• On the external component, set the digital output format to PCM, as the CD receiver supports only PCM signals. (CR-

725DAB)

• Make sure the correct input source is selected (see page 26).

• Make sure the analog audio cable is connected correctly (see pages 19 to 24).

• Make sure that all audio connecting plugs are pushed in all the way (see page 18).

No sound is heard from your turntable.

• Make sure the turntable has a built-in phono equalizer.

• If the turntable doesn’t have a phono equalizer built-in, you must provide one.

Timer playback or recording doesn’t work.

• Make sure the clock has been set correctly (see pages 49, 50).

• Timed operation will fail if the CD receiver is on at the specified On time, so make sure it’s set to Standby (see

page 53).

• The timer may overlap with another timer. If you program several timers, make sure they don’t overlap (see page 51).

• If you press the [SLEEP] or [TIMER] button while a timed operation is in progress, the timer will be cancelled.

• Make sure the u cables and analog audio cables are connected correctly (see pages 19 to 23).

• If you’re using an Onkyo component for timed playback or recording, you must set the Input Display to match that

component (see page 28).

The time is not displayed in Standby mode.

• Set the CD receiver so that the time is displayed in Standby mode (see page 50).

Remote Controller

External Components

Timers

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s

malfunction. Before you record important data, make sure that the material will be recorded correctly.

The CD receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe

interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this

should happen, unplug the power cord, wait at least 5 seconds, and then plug it again.

Specifications

Specifications and features are subject to change without notice.

General

Power Supply: CR-725: AC 220-230 V, 50/60 Hz

CR-725DAB: AC 230 V, 50 Hz

Power Consumption: 42 W

Stand-by Power Consumption: 0.38 W

Dimensions (W × H × D): 205 × 116 × 338 mm (8-1/16" × 4-9/16" × 13-5/16")

Weight: CR-725: 5.1 kg (11.2 lbs.)

CR-725DAB: 5.2 kg (11.5 lbs.)

Audio Inputs

Digital Inputs: CR-725DAB: 1 (optical)

Analog Inputs: 4 (LINE1, LINE2, MD/TAPE, DOCK/CDR)

Audio Outputs

Analog Outputs: 2 (MD/TAPE, DOCK/CDR)

Subwoofer Pre Outputs: 1

Speaker Outputs: 2

Phones: 1

Amplifier Section

Power Output:

50 W + 50 W (4 Ω, 1 kHz, 1% THD)

THD (Total Harmonic Distortion): 0.5% (Power Rated) 0.08% (1 kHz, 1 W)

Damping Factor:

50 (Front, 1 kHz, 8 Ω)

Input Sensitivity and Impedance:

150 mV/50 kΩ (LINE)

Output Level and Impedance:

150 mV/2.2 kΩ (REC OUT)

Frequency Response: 10 Hz–60 kHz/+1/–3dB (LINE1)

Tone Control: ±6 dB, 80 Hz (BASS)

±8 dB, 10 kHz (TREBLE)

+8 dB, 80 Hz (S.BASS)

Signal to Noise Ratio: 100 dB (LINE1, IHF-A)

Speaker Impedance:

4 Ω–16 Ω

Tuner Section

Tuning Frequency Range: 87.50 MHz–108.00 MHz

Usable Sensitivity: Stereo: 22.2 dBf (IHF) Mono: 15.2 dBf (IHF)

Signal to Noise Ratio: Stereo: 67 dB (IHF-A) Mono: 73 dB (IHF-A)

THD (Total Harmonic Distortion): Stereo: 0.5% (1 kHz) Mono: 0.3% (1 kHz)

Stereo Separation: 40 dB (1 kHz)

DAB (CR-725DAB only)

Tuning Frequency Range: 174.928–239.200 MHz

Frequency Response: 20 Hz–20 kHz

Signal to Noise Ratio: 94 dB

THD (Total Harmonic Distortion): 0.09%

Frequency Response: 4 Hz–20 kHz

Audio Dynamic Range: 96 dB

THD (Total Harmonic Distortion): 0.005%

Wow and Flutter: Below threshold of measurability

Audio Output/Impedance (Analog):

1.3 V (rms)/1 kΩ

SN 29344774

Y0804-1

http://www.onkyo.com/

HOMEPAGE

Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/

ONKYO EUROPE UK Office

Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ

UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452

ONKYO CHINA LIMITED

Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,

N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039

http://www.ch.onkyo.com/

* 2 9 3 4 4 7 7 4 *

Onkyo CS-725 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Onkyo CS-725

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info