Handleiding Okbaby Orion (pagina 7 van 51) (Alle talen)

773004

Verklein

Vergroot

Pagina terug

1/51

Pagina verder

8 9Front mounted child bicycle seat Okbaby Orion Front mounted child bicycle seat Okbaby Orion

ENGLISH

4) WARNING: Never park the bicycle leaving the child unattended in

the seat.

5) WARNING: Do not use the seat if any part is missing or broken.

6) WARNING: A front mounted seat can reduce the manoeuvrability of

the handlebar.

7) It is recommended to change the type of handlebar if the steering

angle for each side is less than 45 °.

Mounting and assembling the child seat

Illustration 1:

Holding the seat upside-down, insert the support arm (6).

Illustration 2:

After having lifted up the padding in the seating area, insert the short-

est two screws (10) in the holes.

Illustration 3:

Place the fixing plate (12) in correspondence with the screws (10) pro-

truding from the bottom of the seat. Attach the clamp using the two M6

hexagonal nuts with the toothed washer.

Illustration 4:

With the screws loosened, place the support arm in one of three pos-

sible positions, then tighten the nuts using the wrench (14) until they

are tightly fastened. Optimal torque is 8Nm.

Illustration 5A-5B

Choose the plastic reduction (11) which is adapted to the diameter of

the bicycle’s steerin tube and insert it in the fastening block (7). Each

reduction shows the reference diameters. Apply the covers (9) to the

U-shaped brackets (8). Choose one of the possible configurations based

on the type of bicycle frame you have, as shown in figure 5B. Insert

the ends of the U-shaped brackets (8) in the fastening block (7), in the

rotating pins (15) and then secure them with the 4 hexagonal nuts (16).

Apply the casings (17) to cover the protruding parts of the U-shaped

brackets (8).

Illustration 6:

Take the seat and insert the two ends of the support arm (6) into the

fastening block holes. Verify that the support arm is correctly inserted

and locked by the safety spring release: pulling the seat upwards, this

should not exit the fastening block.

In case the seat interferes with the handlebars or with pedalling, return

to the illustration 4 and adjust the support arm of the seat, moving it

forwards or backwards as required.

Illustration 7:

To remove the seat, hold the centre button of the fastening block (7)

and pull the seat upwards.

Illustration 8:

Insert each footrest (4) with the respective strap in the relative housing.

Illustration 9:

Pass the four hooks (18) in the housings provided and press down until

the catch snaps (19).

To adjust the height of the footrests:

• Push the catch (19) with a finger from the outside, while raising the

footrest with the other hand, then remove the footrest from its housing.

• Insert the footrest in the desired position.

Use of the seat:

Illustration 10:

Only mount the seat between the handlebars and the bicycle saddle.

Illustration 11:

Apart from the safety belts, the Orion child’s seat has a bumper bar

that prevents the child from getting up and moving around dangerously

while being carried. To open the bumper bar, push the button (20).

Take the bumper bar out of its housing by rotating it until it stops.

Illustration 12:

After having seated the child, close the bumper bar until the button

(20) is completely inserted in its housing. Check that the bumper bar is

blocked.

Illustration 13:

When the child is seated in the seat, secure his/her feet by passing the

strap under the bracket (21), and blocking the strap on the pin (22) in

the desired position. To release the child’s feet, pull the strap outwards

to release it from the pin (22).

Illustration 14:

The bumper bar is suitable for children who are a few months old

(weighing about 7 to 10 Kg). When the child weighs over 10kg, the

bumper bar could squeeze the child and it would therefore be necessary

to remove it. In this way the seat can be used up to a maximum child

weight of 15kg. To remove the bumper bar, exercise pressure with a

normal screwdriver, removing the cap blocking the pin.

Illustration 15:

At this point the pin can be extracted from the housing, releasing the

bumper bar.

Illustration 16:

Using light pressure, snap the two closing caps (13) into place to close

the openings that have been formed due to the absence of the bumper

bar.

Illustration 17:

If you want to replace the bumper bar, remove the closing caps (13) and

put the bumper bar back into place using the relative screw and nut,

tightening it with the wrench supplied (14).

Illustration 18:

Fasten the child with the seat belts by adjusting the length based on

the child’s height. The adjustment is achieved by sliding the buckles on

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Okbaby Orion Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Okbaby Orion

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info