709108
51
Verklein
Vergroot
Pagina terug
1/144
Pagina verder
51
Diagnostic display
B-1200
Diagnostic display
Number State Diagnosis / Remedy
The operator starts up and
“0”goes out.
In normal operation, drive receives start signal via START input or
by drive unit.
Garage door has reached end
position OPEN.
Garage door has reached end
position CLOSE.
End position has not been
reached.
The display shows a “0” during
the next opening and closing
cycle and then goes out.
The operator is carrying out a learning cycle for the force limit.
Caution: During this travel cycle the operator does not monitor the
force. Make sure that no persons or objects are in the travel path
of the garage door.
The display continues to show a
“0”.
The force-learning cycle did not complete and must be repeated.
The door’s end-of-travel position may have too much pressure.
Set the door’s pressure to the correct level.
The door does not open or close. Interruption at STOP A or activation of an external safety device
(such as a pass-door).
The door does not close. Interruption at STOP B or activation of an external safety device
(such as a photoelectric sensor).
The door setting and learning
cycle did not complete correctly.
You must use menu stages 3 and 4 to complete the door settings
correctly and then complete the force-learning cycle.
There is a permanent impulse
signal at the start input.
Start signal is not detected or pulse duration (eg button jammed).
An error occurred in setting the
operator.
The travel path is too long.
Repeat setting procedure with menu stages 3 and 4.
Visual closing edge protection
OSE or electrical contact strip 8k2
has tripped.
Check the connection/wiring.
Error in learning cycle. Repeat position learning cycle with menu stages 3 and 4.
Reduce force when approaching the end-of travel positions.
The door does not open or close. An error occurred during the self-test. Disconnect the power
supply.
Motor standstill. The motor does not rotate. Call a specialist company to repair the
motor.
Electronic brake activated. The
garage light remains on.
The drive is pulled from the upper end position. Check the door
and the springs. Setting upper end lower.
The vacation lock is activated.
The door does not open.
The side switch for SafeControl/Signal 112 is active. A reset is
required.
51

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Novoferm Novomatic 823S B1200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Novoferm Novomatic 823S B1200 in de taal/talen: Nederlands, Duits, Engels, Frans, Deens als bijlage per email.

De handleiding is 6,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info