474198
11
Verklein
Vergroot
Pagina terug
1/31
Pagina verder
Deleting all the hand transmitters programmed
for the operator:
Plug in the operator's mains plug and whilst
button pressed.
Menu stage 3: Setting/adjusting the top
end of-travel position
Keep button pressed for 3 seconds.
Number 3 appears in the display.
Wait a short while until the 3 starts flashing.
Press button . The operator causes the door
to travel in the OPEN direction as long as the
button is pressed. The position can be altered
to the CLOSE direction via button .
Once the desired OPEN end-of-travel position
has been reached, press button . The
operator stores the OPEN end-of-travel
position and "4" appears in the display.
Menu stage 4: Setting/adjusting the
bottom end-of-travel position
Wait a short while until "4" starts flashing.
Press button . The operator causes the door
to travel in the CLOSE direction as long as the
button is pressed. The position can be altered
to the OPEN direction via button .
Once the desired CLOSE end-of-travel
position has been reached, press button .
The operator stores the CLOSE end-of-travel
position and "5" appears in the display.
Press button twice until "0" appears.
18a Force-learning cycle
Attention: During this opening and closing
cycle the operator learns the force required to
open and close the door. A force limit does not
apply! The cycles must not be interrupted.
During these cycles "0" appears in the display.
- Press button . The operator causes the
door to open until the top end-of-travel
position has been reached.
- Now press button again. The operator
causes the door to close until the bottom end-
of-travel position has been reached.
- After approx. 2 seconds "0" goes out.
Menu stage 5: The opening force limit
If you have previously quit the setting menu,
press button for 3 seconds until "3"
appears. Then press button twice until "5"
appears.
After approx. 2 seconds the display flashes
showing the set value of the opening force
limit.
The force limit setting can be increased or
decreased via buttons and .
After setting the value, press button .
The display shows "6".
Menu stage 6: The closing force limit
After approx. 2 seconds the display starts
flashing and the set value for the closing force
limit is displayed.
The force limit setting can be increased or
decreased via buttons and .
After setting the value, press button . "0"
appears in the display.
Finally, check the force settings and, if
necessary, repeat the setting procedure.
The maximum force at the main closing edge
must not exceed 150N!
Caution! If the force setting is too high,
persons may be placed at risk of injury.
The factory setting is 4!
Programming the Operator
Control elements
The controls for programming the door
operator are protected by a transparent cover.
The transparent cover can be opened with a
screwdriver.
After the operator has been programmed, the
transparent cover must be closed again.
A - Numerical display shows the menu stage
as well as the selected value.
a - Point display, lights up to indicate "ready
for operation" and flashes on the hand
transmitter code learning completion.
B - Button during the setting/adjustment
phase serves as an "up" button and
outside the menu as a start button.
C - Button during the setting/adjustment
phase serves as a "down" button.
D - Button is used to call up the
setting/adjustment menu, to change the
menu stages and to store the settings.
Programming the control unit is menu-driven.
Pressing button calls up the menu guide.
The numbers displayed indicate the menu
stage. After approx. 2 seconds the display
flashes and the setting can be altered via
buttons and .
The selected setting is stored with button
And the programme jumps automatically to the
next menu stage. By repeatedly pressing
button menu stages can be skipped. To
quit the menu, press button until "0" is
shown again. Outside the menu, button can
be used to generate a start impulse.
Before programming
- Allow door to engage into the carriage.
- Pull out the mains plug. Point display (a)
lights up.
- Make sure that the aerial is correctly
positioned (see figure 13).
- Observe the hand transmitter instructions.
Menu stage 1: Programming the start
function for the hand transmitter
Briefly press button .
"1" is displayed.
As soon as the display flashes, press and keep
pressed for approx. 1 second the button of the
hand transmitter, with which you later wish to
start the operator.
As soon as the code has been read, the red
point display (a) flashes five times before
quitting.
Further hand transmitters (up to a maximum of
10) can be programmed.
Menu stage 2 : Programming the light
function for the hand transmitter
Press button .
"2" appears in the display.
Note: If no 4-minute light is to be programmed,
repress button . The display shows "0" -
programming is completed.
Press the second button on the hand
transmitter, with which the 4-minute light is to
be switched on.
As soon as the code has been read, the red
point display (a) flashes five times before
quitting.
After the code has been learned, briefly press
button .
"0" appears indicating that you have come to
the end of the menu.
1414
1515
1616
1818
1717
2121
1919
2020
Checking the force limit facility
- Place an obstruction (e. g. operator's
cardboard box) underneath the door's
cosing edge.
- Starting from the OPEN end-of-travel
position, actuate the door to close.
- The door travels towards the obstruction,
stops and travels back to the top end-of-
travel position.
- The point display (a) must switch off for
approx. 1 second. Then the operator
functions as normal again.
If the door springs have been changed or
altered, then the force learning cycle must be
repeated:
Proceed to menu stage 5 and keep button
Pressed for 3 seconds. "0" appears in the
display. Then complete the force learning cycle
as explained under point 18a.
Special settings
Menu stage 7: Light phases
Press button for 3 seconds.
"3" appears in the display.
Press button several times until menu
stage 6 is shown.
Keep button pressed again for 3 seconds
until "7" appears in the display.
Menu Light phase Warning
value phase
If the warning phase is set, the light flashes
before the door starts to move and during the
actual travel cycle. The factory setting is 1.
Menu stage 8: "Soft" start and "soft" stop ("soft"
runs)
Press button . "8" appears in the display.
These values correspond to the "soft" runs
measured in cm at the carriage.
Important note:
The factory setting of 4 must be adhered to.
The "soft" runs may only be altered on the
express permission of the door manufacturer.
Press button . "0" appears in the display.
0 60 s -
1 90 s -
2 120 s -
3 240 s -
4 0 s 3 s
5 90 s 3 s
6 240 s 3 s
7 0 s 10 s
8 90 s 10 s
9 240 s 10 s
Menu Start Stop Start Stop
Value Open Open Close Close
0 0 0 0 0
1 15 0 15 0
2 0 15 0 60
3 15 15 15 35
4 25 45 25 45
5 15 15 15 60
6 15 15 15 15
7 35 35 35 50
8 60 15 15 85
9 soft run only
Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!
GB
11

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Novoferm-Novomatic-553

Zoeken resetten

  • Motor novomatic 553 reageert omgekeerd ten opzichte van de drukknoppen.
    Hoe kan ik de motor resetten? Gesteld op 18-10-2022 om 19:30

    Reageer op deze vraag Misbruik melden
  • Hallo, wij zijn beide handzenders kwijt van onze garagedeur van het merk novaferm.
    Handmatige slot is stuk.
    Is er een manier om de garage deur toch te openen zonder te slopen.?

    Groet Gesteld op 25-9-2021 om 12:31

    Reageer op deze vraag Misbruik melden
  • Is het mogelijk dat, indien batterij van muurkastje dient vervangen te worden, de afstandsbediening ook niet meer werkt en de motor ontregeld is?? dank. Gesteld op 11-8-2021 om 15:15

    Reageer op deze vraag Misbruik melden
    • Als de motor niet meer reageert op de adstandsbediening haal dan de stekker eruit.Wacht 10 seconden en en sluit weer aan.Na een tweede keer drukken op de a.b.werkt de motor weer. Geantwoord op 12-8-2021 om 07:48

      Waardeer dit antwoord (2) Misbruik melden
  • Dien de lamp te vervangen van de Novomatic 553. Kan iemand me vertellen hoe ik dit het beste aanpak? Gesteld op 22-8-2020 om 15:23

    Reageer op deze vraag Misbruik melden
  • Ik heb de foutmeding nr 8 op het systeem tegen de muur , en mijn poord gaat niet meer automatisch open , kheb ook reeds een reset gedaan , maar dit helpt niet . Kunt U mij helpen aub.?
    Mvg
    Jan Gesteld op 26-2-2020 om 19:09

    Reageer op deze vraag Misbruik melden
  • We hebben twee afstandbedieningen bij onze novoterm 553.Beide batterijen vernieuwd.de deur opent zeer regelmatig niet meer.5/6 keer per week.Na stroom verwijderen (met een trapje stekker uit plafond en er weer in)werkt de deur weer.2 a 3 keer en dan zelfde probleem.Bekend bij iemand? BVD. Gesteld op 25-2-2019 om 12:46

    Reageer op deze vraag Misbruik melden
6
  • dank voor reactie.We hebben de 2 afstandbedieningen opnieuw ingeleerd.dat werkte al en daarna de riem extra aangespannen.Hij gaat weer normaal gelukkig. Geantwoord op 13-3-2019 om 12:33

    Waardeer dit antwoord (4) Misbruik melden
  • Wil externe led lamp aansluiten op novoferm 3 maar er zit continu stroom op aansluitblokje ?? Gesteld op 26-11-2018 om 21:43

    Reageer op deze vraag Misbruik melden
    • Ik heb een Novomatic 553 en heb een externe led lamp 220V 3watt aangesloten op de desbetreffende klem (light ext.) aangesloten en het heeft altijd gewerkt tot verleden week dat de lamp blijft branden, ik vermoedde dat het relais bleef hangen maar dat is niet zo en daarom denk ik nu dat het waarschijnlijk een IC is die het relais aanstuurt die defect is maar welke ic is het?? iemand een idee? ik ben op het net op zoek gegaan naar het schema maar niet gevonden?? help, alvast bedankt, greetz Geantwoord op 8-6-2020 om 21:10

      Waardeer dit antwoord Misbruik melden
  • Als je al het idee hebt dat er een IC defect is en je kan het zelf niet opsporen dan zou ik met de vingers van de print afblijven.. ;) Geantwoord op 22-7-2020 om 16:37

    Waardeer dit antwoord Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Novoferm Novomatic 553 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Novoferm Novomatic 553 in de taal/talen: Nederlands, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info